Instruction d'utilisation RODE Microphones NT55

Résumé du contenu de la page N° 1

NT55
Instruction Manual
( )
EMC, LVD

Résumé du contenu de la page N° 2

N NT T5 55 5 N NT T5 55 5 The NT55 is complemented with a I want to thank you for purchasing a NT55. diverse range of accessories to better facilitate positioning and attachment. For Please take the time to read this manual more details of these accessories and any as it contains information that will help additions to the range visit our website: you achieve the best results from your www.rodemic.com microphone, as well as help you get If you have any questions or comments, many ye

Résumé du contenu de la page N° 3

N NT T5 55 5 N NT T5 55 5 Specifications Specifications cont. Acoustic Principle: Externally polarised 1/2” (13 mm) Output Impedance: pressure gradient condenser. 100 Ω Directional Pattern: Signal/Noise ratio DIN/IEC 651: 0 79 dB (1 kHz rel 1 Pa; per IEC651, +5.0 0.0 -2.0 IEC268-15) -4.0 -6.0 -8.0 -10.0 -12.0 -14.0 Equivalent Noise: -16.0 -18.0 -20.0 -22.0 15 dB SPL (per IEC651, -24.0 -25.0 90 270 dB rel. 1V/Pa IEC268 -15) 500 Hz 1000 Hz 4000 Hz Maximum SPL: 136 dB (@ 1% THD into 1 k

Résumé du contenu de la page N° 4

�� N NT T5 55 5 N NT T5 55 5 Powering your NT55 Specifications cont. The NT55 is designed to operate Dimensions: from phantom power to the P48 ���������������� standard, between 44 V and 52 V and P24 standard, between 20 V and 28 V, applied with positive polarity to pin 2 and pin 3 of the output XLR connector. �������������� The NT55 will operate satisfactorily into a load impedance as low as 1 k Ω. If a Features load below this is used, the output signal level will be reduced. The

Résumé du contenu de la page N° 5

N NT T5 55 5 N NT T5 55 5 of the NT55, align the slot on the XLR connector to the groove on the inside of NT55 body and insert (see fig 4). Ensure that the connector can not be removed without depressing the release button. (See fig. 5). fig. 2 fig. 3 NT55 Controls You will notice the holder is quite firm. This is intended to stop the mic from coming loose. Ensure Now that you have the NT55 you leave the high-pass filter and securely fastened to a mic stand Pad controls facing upw

Résumé du contenu de la page N° 6

N NT T5 55 5 N NT T5 55 5 as attenuation. The 3-position Changing capsules variable High-Pass Filter enables you to step from a flat response to The NT55 capsules are designed 75 or 150 Hz cut. to be user friendly and switching Use the high pass filter when you between capsules is easy. wish to remove low frequency noise that is not part of your First make sure that the mic is intended sound source. disconnected from all power by removing the XLR. Once this is Remember however th

Résumé du contenu de la page N° 7

N NT T5 55 5 N NT T5 55 5 Accessories Warranty Service has a full line of * The NT55 is warranted accessories such as wind shields, for 1 year from the date of boom poles etc., so contact your purchase. You can extend that to a local dealer or visit the RØDE full ten years if you can register on website for more details - www. line at www.rodemic.com. rodemic.com. The warranty covers parts and labour that may be required to repair the microphone during the warranty period. The wa

Résumé du contenu de la page N° 8

International: Microphones. Unit 2/107 Carnarvon Street Silverwater NSW 2128 Australia Ph: 61 2 9648 5855 Fax: 61 2 9648 2455 USA: P.O. Box 3279 Torrance, CA 90510-3279 Ph: 877 328 7456 (Toll Free Within the US) Ph: 310 328 7456 Fax: 310 328 7180 Technical Support: For information and technical support questions contact: support@rodemic.com In the Unites States and Puerto Rico, contact: support@rodemic.com or call 877 328 7456 toll free or 310 328 7456 In Australia, contact: support@rodem