Instruction d'utilisation Ranger RCI-6300F25/150

Résumé du contenu de la page N° 1

Table of Contents

PAGE
Chapter 1 Specifications ........….............................................. 2

Chapter 2 Installation .......….................................................. 3

Installing the Radio................................................................. 3
Ignition Noise Interference ...................................................... 4
Antenna ….............................................................................. 4
RCI-6300F25/150
Ex

Résumé du contenu de la page N° 2

Chapter 1 Specifications Chapter 2 Installation GENERAL Installing the Radio Model RCI-6300F25 RCI-6300F150 Choose a convenient location for operation that does not interfere with Frequency Range : 1. 28.245 ~ 28.685 MHz 1. 28.245 ~ 28.685 MHz drive or passenger. This radio is supplied with a universal mounting 2. 28.695 ~ 29.135 MHz 2. 28.695 ~ 29.135 MHz bracket. When mounting the bracket and radio to your car, make sure it is 3. 29.145 ~ 29.585 MHz 3. 29.145 ~ 29.585 MH

Résumé du contenu de la page N° 3

Installation (Continued) Chapter 3 Operation Controls and Indicators 4. Mount the microphone bracket near the radio in an easily accessible Front Panel spot using the two screws provided. 11 12 13 14 15 16 17 18 19 20 Ignition Noise Interference With weak signals, you may experience interference of the signal by background noise. This radio has NB and ANL controls which will help Ranger reduce background noise from sources such as your ignition system. However, backg

Résumé du contenu de la page N° 4

Operation (Continued) Operation (Continued) 5. MODE SWITCH: This switch allows you to select one of three position, the Standing Wave Ratio (SWR) of your antenna. There are no following operating modes: PA/FM/AM. adjustments because the SWR circuit this radio calibrates itself automatically. 6. Fr. POOL: The Frequency Pool allow the user to select the desired 17. NB/ANL SWITCH: In the NB/ANL position, the RF Noise Blanker and segments of frequencies. the automatic Noise Lim

Résumé du contenu de la page N° 5

Operation (Continued) Operation (Continued) Rear Panel Operation A. Microphone 34 The receiver and transmitter are controlled by the push-to-talk switch on the microphone. Press the switch and the transmitter is activated, release ANT. switch to receive. When transmitting hold the microphone two inches PA.SP. EXT.SP. from the mouth and speak clearly in a normal “voice”. The transceiver _ + POWER comes complete with low-impedance dynamic microphone. For be

Résumé du contenu de la page N° 6

Operation (Continued) Memo B. Procedure to Receive 1. Be sure that power source, microphone and antenna are connected to the proper connectors before going to the next step. 2. Turn unit on by turning VOL knob clockwise. 3. Set the VOL for a comfortable listening level. 4. Set MODE switch to the desired operation mode. 5. Listen to the background noise from the speaker. Turn the SQ knob slowly clockwise until the noise just disappear. This SQ is now properly a

Résumé du contenu de la page N° 7

Ranger Communications Limited Warranty Ranger Communication, Inc. (Ranger) warrants to the original purchaser only this product against defects in material or workmanship, as noted below. Effective December 1, 2001, the following Ranger Communications, Inc.'s products are covered by a two (2) year limited warranty: 1. Amateur Radio Products: RCI-2950DX, RCI-2970DX, RCI-2980WX, RCI- 2985DX, RCI-2990DX, RCI-2995DX, RCI-6300FHP, RCI-6300FTB, RCI- 6900FHP, RCI-6900FTB.