Résumé du contenu de la page N° 1
VHF 100/200 Series Radio Installation Instructions
These installation instructions are for the following VHF radios and handsets:
North American Models International Models
VHF 100 VHF 100i
VHF 200 VHF 200i
GHS 10 GHS 10i
®
Compare the contents of this package with the packing list on the box. If any pieces are missing, contact your Garmin dealer immediately.
Before you begin the installation:
• Read these instructions thoroughly.
• Gather the appropriate fasteners and tools.
• Verify that all
Résumé du contenu de la page N° 2
Installing your VHF 100/200 Series Radio 1. Select a location (page 2). 2. Mount the radio (page 2). 3. Connect the radio to power (page 4). 4. Connect the radio to an antenna (page 5). 5 Mount the microphone hangar (page 5). Although they are not necessary to use your radio, these instructions cover the following additional installation options. • Connecting the radio to a chartplotter (page 5) • Connecting the radio to a hailer horn (page 7) • Connecting the radio to an external speaker (page
Résumé du contenu de la page N° 3
Flush Mounting the VHF 100/200 Series Radio In addition to the four included 4.2 × 25 mm, panhead mounting screws, flush mounting the VHF 100/200 series radio requires the following tools (not included): • Phillips screwdriver • Drill and 9/64 in. (3.5 mm) drill bit for mounting holes • 3/8 in. (10 mm) drill bit for a starter hole • Jigsaw • Scissors and tape • Center punch and hammer • File and sandpaper • Anti-seize lubricant (optional) Note: Ensure that the surface on which you mount the VH
Résumé du contenu de la page N° 4
+ - Step 3: Connect the VHF 100/200 Series Radio to Power The VHF 100/200 series radios have a power-cable wiring harness that connects to power and provides interface capabilities for connecting external devices. Notes: • The replacement fuse on the power cable wiring harness is a 10 A, slow-blow fuse. • If it is necessary to extend the power wires, use 18 AWG wire. • If your boat has an electrical system, you might be able to wire the radio directly to an unused holder on your current fuse bl
Résumé du contenu de la page N° 5
Step 4: Connect the VHF 100/200 Series Radio to an Antenna Connect a marine VHF antenna to the radio using the antenna port on the rear panel of the radio. Mount the antenna according to the installation instructions provided with the antenna. Antenna port Step 5: Mounting the Microphone Hanger Drill the mounting holes using a 1/8 in. (3 mm) drill bit. Use three of the included 3.5 × 20 mm, panhead mounting screws to mount the microphone hanger in a convenient location near the radio. Connecti
Résumé du contenu de la page N° 6
Connecting a VHF 200 Series Radio to a NMEA 2000 network The VHF 200 and VHF 200i radios can be connected to your existing NMEA 2000 network, or you can build a basic NMEA 2000 network to connect to another NMEA 2000-compatible device, such as a chartplotter. For more information on NMEA 2000 and to purchase required connectors, visit www.garmin.com. Note: The VHF 100 and VHF 100i radios cannot be connected to a NMEA 2000 network. See page 5 to connect your radio to a NMEA 0183 network. To
Résumé du contenu de la page N° 7
4. Add additional T-connectors for each device you want to add to the NMEA 2000 network, and connect each device to a T-connector with a drop cable. 5. Connect terminators (not included) to each end of the combined T-connectors. Ignition or in-line switch Fuse NMEA 000 device + - Drop cable 1 Vdc battery Power cable T-connectors Female Male terminator terminator Creating a Basic NMEA 2000 Network NMEA 2000 PGN information Use this table to determine the approved NMEA 2000 PGN information
Résumé du contenu de la page N° 8
Connecting the VHF 100/200 Series Radio to an External Speaker (Optional) The radio can be connected to an external speaker that allows you to hear your radio at a remote location. To mount the external speaker, refer to the installation instructions that came with the speaker. To connect the VHF 100 series radio to an external speaker: 1. Connect the yellow wire on the wiring harness (located on the rear panel of the radio) to the positive (+) connection on the external speaker. 2. Connect th
Résumé du contenu de la page N° 9
9 /6 in. (.5 mm) drill bit Recommended clearance for sun cover Recommended clearance for sun cover handle Pilot hole 1 3 /4 in. (82.4 mm) Recommended clearance for DISTRESS key door 15 6 /32 in. (164 mm) VHF 100/200 Series Flush-Mount Template VHF 100/00 Series Radio Installation Instructions
Résumé du contenu de la page N° 10
© 2010 Garmin Ltd. or its subsidiaries Garmin International, Inc. st 1200 East 151 Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK Garmin Corporation nd No. 68, Jangshu 2 Road, Sijhih, Taipei County, Taiwan www.garmin.com May 2010 190-01019-02 Rev. G Printed in China
