Résumé du contenu de la page N° 1
IMPORTANT MANUAL Do Not Throw Away
00993-poulan_pro
02478
OWNER'S MANUAL
WARNING:
Read this Owner's Man u al and follow all Warn-
MODEL:
ings and Safety Instructions. Fail ure to do so
can re sult in serious in ju ry.
PD18H42STB
LAWN TRACTOR
ALWAYS WEAR EYE PROTECTION DURING OPERATION
187080 04.17.03 TR
Printed in U.S.A.
Résumé du contenu de la page N° 2
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS . FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. DO NOT: I. GENERAL OPERATION Do not turn on slopes unless necessary, and then, Read, understand, and follow all instructions in the manual and on the machine before starting. turn slowly and gradually downhill, if possible. Only al
Résumé du contenu de la page N° 3
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS Be sure the area is clear of other people before mowing. Stop WARNING: In order to prevent ac ci - machine if anyone enters the area. den tal starting when setting up, trans- Never carry passengers or children even with the blades port ing, ad just ing or making repairs, off. al ways dis con nect spark plug wire Do not mow in reverse unless absolutely necessary. Al ways and place wire where it can not contact look
Résumé du contenu de la page N° 4
CONGRATULATIONS on your purchase of a new tractor. PRODUCT SPECIFICATIONS It has been designed, engineered and manu factured to giv e Gasoline Capacity 2.0 Gallons you the best possible dependability and performance. and Type: Unleaded Regular Should you experience any problem you cannot easily rem- Oil Type(API-SF-SJ): SAE 10W30 (above 32°F) edy, please contact your nearest authorized service center/ SAE 5W-30 (below 32°F) department. We have competent, well-trained tech ni cians Oil
Résumé du contenu de la page N° 5
UNASSEMBLED PARTS Seat Steering Wheel (1) Washer 17/32 x 1-3/16 x 12 Gauge Steering Wheel Insert (1) Knob Gauge Wheel (4) Steering Adjusting (4) Wheels Extension Bar Shaft Steering Sleeve (4) Locknut 3/8-16 (4) Clevis Pins (4) Retainer Springs (double loop) (1) Large Flat (4) Washers Washer Steering Adapter 3/8 x 3/4 x 14 Ga. (4) Shoulder Bolt Slope Sheet (1) Locknut 1/2-20 (1) Oil Drain Tube (1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut 1/4-28 (2) Mulch Blades (2) Key
Résumé du contenu de la page N° 6
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY INSERT A socket wrench set will make assembly easier. Stan dard 1/2 HEX NUT wrench sizes are listed. Utility knife Pliers LARGE FLAT WASHER (1) 3/4" wrenc
Résumé du contenu de la page N° 7
ASSEMBLY Roll tractor forward off skid. SEAT Remove banding holding the defl ector shield up against tractor. TO DRIVE TRACT OR OFF SKID (See Op- er a tion section for location and function of SEAT PAN con trols) W ARNING: Before start ing, read, un der stand and fol low SHOULDER all in struc tions in the Op era tion section of this manu al. Be BOLT sure tractor is in a well-ventilated area. Be sure the area in 02466 front of tractor is clear of other peo ple and objects.
Résumé du contenu de la page N° 8
ASSEMBLY IMPORTANT: FOR SHIPPING PURPOSES, THE MULCHER CHECK DECK LEVELNESS PLA TE WAS PREA TT ACHED TO Y OUR MOWER. THE MULCHER PLATE MUST ONLY BE USED WITH THE MULCHING BLADES For best cutting results, mower housing should be properly THAT CAME PACKED SEPARATELY IN THE CARTON. leveled. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. YOUR MOWER CAME FACTORY EQUIPPED WITH HIGH PERFORMANCE BLADES, WHICH ARE THE BEST BLADES FOR BAGGING AND DISCHARGING. TO
Résumé du contenu de la page N° 9
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. FAST IGNITION REVERSE NEUTRAL HIGH LOW SLOW CHOKE P LIGHTS ON ENGINE ON ENGINE START PARKING BRAKE ENGINE OFF PARKING BRAKE PARKING BRAKE LOCKED UNLOCKED FUEL OIL PRESSURE BATTERY REVERSE FORWARD OVER TEMP MOWER HEIGHT MOWER LIFT LIGHT 15 15 15 ATTACHMENT ATTACHMENT SLOPE HAZARDS CLUTCH ENGAGED CLUTCH DISENGAGED DANGER, KEEP HANDS KEEP AREA CLEAR AND FEET AWAY
Résumé du contenu de la page N° 10
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. IGNITION LIGHT AT TACHMENT SWITCH SWITCH CLUTCH LEVER AMMETER POSITION LIFT LEVER THROTTLE/ PLUNGER CHOKE CONTROL ATTACHMENT LIFT LEVER CLUTCH/ BRAKE PEDAL HEIGHT ADJUSTMENT KNOB PARKING BRAKE MOTION CONTROL FREE WHEEL LEVE
Résumé du contenu de la page N° 11
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per forming an y adjustments or repairs. We rec om mend a wide vision safety mask over spec- tacles or stan dard safety glasses. Never use choke to stop engine. HOW TO USE YOUR TRACTOR IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY T
Résumé du contenu de la page N° 12
OPERATION TO ADJUST GAUGE WHEELS (See Fig. 7) "ENGAGED" PO SI TION Gauge wheels are properly adjusted when they are slightly ATTACHMENT LIFT LEVER off the ground when mower is at the desired cutting height HIGH PO SI TION in operating position. Gauge wheels then keep the deck AT TACHMENT in proper position to help prevent scalping in most terrain CLUTCH LEVER conditions. LOW "DIS EN GAGED" POSITION PO SI TION NOTE:Adjust gauge wheels with tractor on a fl at level surface. Adjust mowe
Résumé du contenu de la page N° 13
OPERATION Transmission Engaged IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GAS O LINE TO HELP INSURE GOOD COLD WEATHER START ING. CAUTION: Alcohol blended fuels (called gas o hol or using ethanol or methanol) can at- tract moisture which leads to sep a ra tion and forma tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before stor a
Résumé du contenu de la page N° 14
OPERATION AUTOMATIC TRANSMISSION WARM UP Slowly move motion control lever forward, after the Before driving the unit in cold weather, the trans mis sion tractor moves approximately fi ve (5) feet, slowly move should be warmed up as follows: motion control lever to reverse position. After the trac- tor moves approximately fi ve (5) feet return the mo- Be sure the tractor is on level ground. tion control lever to the neutral (N) position. Repeat Place the motion control lever i
Résumé du contenu de la page N° 15
OPERATION MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN MAX 1/3 AFTER EACH USE. The spe cial mulch ing blade will recut the grass clip- pings man y times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biode- grade quick ly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will
Résumé du contenu de la page N° 16
maint_sch-tractore.new1 MAINTENANCE MAINTENANCESCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES Check Brake Operation Check Tire Pressure Check Operator Presence and Interlock Systems T Check for Loose Fasteners R 5 A Sharpen/Replace Mower Blades 3 C Lubrication Chart T Check Battery Level 4 0 Clean Battery and Terminals R Check Transaxle Cooling Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (without oil filter) 1,2 E Clean Air
Résumé du contenu de la page N° 17
MAINTENANCE MANDREL TRACTOR TRAILING ASSEMBLY EDGE UP Always observe safety rules when performing any main- BLADE te nance. CEN TER HOLE BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. FLAT WASHER (See “TO ADJUST BRAKE” in the Service and Ad just ments LOCK WASHER section of this manual). STAR TIRES BLADE BOLT (GRADE 8)* Maintain proper air pressure in all tires (See “PROD UCT *A GRADE 8 HEAT TREA
Résumé du contenu de la page N° 18
MAINTENANCE TO CLEAN BATTERY AND TERMINALS Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. TO CHANGE ENGINE OIL (See Figs. 14 and 15) Disconnect BLACK battery cable fi rst then RED bat- Determine temperature range expected before oil change. ter y cable and remove battery from tractor. All oil must meet API service classifi cation SF-SJ.
Résumé du contenu de la page N° 19
MAINTENANCE NOTE: Operating the engine with a blocked grass screen, MUFFLER dirty or plugged cooling fi ns, and/or cooling shrouds re moved Inspect and replace corroded muffl er and spark arrester will cause engine damage due to overheating. (if equipped) as it could create a fi re hazard and/or dam- age. ENGINE OIL FILTER Replace the engine oil fi lter every season or every other SPARK PLUGS oil change if the tractor is used more than 100 hours in Replace spark plugs at the beginning of ea
Résumé du contenu de la page N° 20
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR AD JUST - MENTS Depress clutch/brake pedal fully and set parking brake. Place motion control lever in neutral (N) position. Place attachment clutch in “DISENGAGED” position. Turn ignition key to “STOP” and remove key. Make sure the blades and all moving parts have completely stopped. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. IMPOR
