Résumé du contenu de la page N° 1
Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR’S MANUAL
22-inch Rotary Mower — Model 038
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state
Résumé du contenu de la page N° 2
This Operator’s Manual is an important part of your new lawn mower. It will help you assemble, prepare, and maintain the unit for best performance. Please read and understand what it says. Table of Contents Slope Gauge ....................................................... 3 Troubleshooting ................................................ 16 Safe Operation Practices ................................... 4 Safety Labels .................................................... 17 Setup and Adjustmen
Résumé du contenu de la page N° 3
����������������������������������������������� ������������������������������������������������� ���������������������������� ��������������� ��� Use this page as a guide to determine slopes where you may not operate safely. Do not operate your lawn mower on such slopes. 1 Slope Gauge WARNING Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. If operating a walk- behi
Résumé du contenu de la page N° 4
WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm. 2 DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects
Résumé du contenu de la page N° 5
19. Shut the engine off and wait until the blade comes to a 7. Extinguish all cigarettes, cigars, pipes and other sources complete stop before removing the grass catcher or unclog- of ignition. ging the chute. 8. Never fuel machine indoor because flammable vapors will The cutting blade continues to rotate for a few seconds after accumulate in the area. the engine is shut off. Never place any part of the body in 9. Never remove gas cap or add fuel while engine is hot or 2 the blade area u
Résumé du contenu de la page N° 6
Loose Parts Carton contents include: wheels, handles (upper & lower), blade control handle, and a hardware pack. Be certain to remove all loose parts before discarding the carton. For convenience of assembly, identify and separate the pieces in the hardware pack according to Figure 3-1 below. A set of adjustable wrenches will be needed for assembly. 3 Setup and Adjustment Reference to right, left, front, or back of the Qty. 2 lawn mower is from the operating position only, unless otherwise
Résumé du contenu de la page N° 7
Spark Plug Wire Disconnect spark plug wire from the spark plug and ground it against the engine. If engine is equipped with a rubber boot, attach rubber boot to a bolt on the engine. 3 This will prevent the engine from firing during assembly. Lower the Discharge Setup and Chute Adjustment 1. For shipping purposes, the chute deflector on your mower is held in an upright position by a retainer. Push chute deflector up towards engine. Holding deflector in this position, remove the retainer
Résumé du contenu de la page N° 8
Attach the Blade Control Handle If the blade control handle became displaced either during 3 shipping or during assembly, reassemble it now. If the blade control handle is firmly in place, you may proceed to the next step. Setup and 1. Insert the curved end of the blade control handle into the right hole, Step A Figure 3-6. Squeeze the handle Adjustment in and insert the straight end of the blade control handle into the left hole of the upper handle, Step B Figure 3-6. 2. Squeeze the bl
Résumé du contenu de la page N° 9
Attach the Recoil Starter NOTE: Use the hardware in Group 5 to secure the recoil starter. 3 1. Loosely attach the rope guide to the outside of the upper handle and thread the wing nut only a few turns, Figure 3-10. Do not tighten. Setup and 2. Depress the blade control handle. Adjustment 3. Pull the recoil starter out of the engine. 4. Slip the rope through the rope guide as shown in Figure 3-10. Tighten the wing nut to secure the rope guide. Reattach the Spark Plug Wire Figure 3-8: Sec
Résumé du contenu de la page N° 10
Adjustments Always stop engine, disconnect Handle Height spark plug, and ground against For convenience of operating, you may adjust the handle 3 height as follows: engine before performing adjustments. 1. Remove the starter rope from the rope guide. 2. Remove the star knobs shown in Figure 3-12 and Cutting Height Setup and remove the lower handles. Each wheel has a height adjustment lever to change the 3. Position each handle bracket stud into the appropriate Adjustment cutting height
Résumé du contenu de la page N° 11
NOTES 11
Résumé du contenu de la page N° 12
Know Your Lawn Mower Blade Control Handle 4 Operating Recoil Starter Your Lawn Mower Cutting Height Adjustment Levers (one at each wheel) WARNING Chute Deflector This blade control is a safety device. Do not bypass its operations. Figure 4-1: The main components on the mower. Use extreme care Now that you have assembled your lawn mower, it’s important to become acquainted with its controls and features. when handling gasoline. Gasoline is Blade Control Handle Gas and Oil Fill-Up extr
Résumé du contenu de la page N° 13
WARNING: The operation of any lawn Using Your Lawn Mower mower can result in foreign objects being Be sure the lawn is clear of stones, sticks, wire, or other thrown into the eyes, which can damage objects which could damage the lawn mower or the your eyes severely. Always wear safety glasses engine. Such objects could be accidently thrown by the while operating the mower or while performing any 4 mower in any direction and cause serious personal injury adjustments or repairs on it. to t
Résumé du contenu de la page N° 14
General Cleaning the Mower Clean underside of the mower deck after each use to Recommendations prevent build-up of grass clippings or other debris. • Always observe safety rules when performing 5 maintenance work. WARNING: Never tip the mower more than 90º in any direction and do not leave the mower • The warranty on this lawn mower does not cover tipped for any length of time. Oil can drain into the items that have been subjected to operator abuse Maintaining upper part of the engine c
Résumé du contenu de la page N° 15
3. Remove blade and adapter from the crankshaft, Off-Season Storage Figure 5-2. The following steps should be taken to prepare your lawn 4. The blade can be sharpened with a file or on a grind- mower for storage. ing wheel. Do not attempt to sharpen the blade while • Clean and lubricate mower thoroughly as described in 5 it is still on the mower. When sharpening the blade, the lubrication instructions. follow the original angle of grind. Grind each cutting • Do not use a pressure washer or
Résumé du contenu de la page N° 16
Remedy Cause Problem Engine fails to start 1. Blade control disengaged. 1. Engage blade control. 6 2. Spark plug wire disconnected. 2. Connect wire to spark plug. 3. Fuel tank empty or stale fuel. 3. Fill tank with clean, fresh gasoline. 4. Engine not choked. 4. Choke engine as instructed in the “Operating Your Lawn Mower” section. Trouble 5. Clean, adjust gap, or replace. 5. Faulty spark plug. 6. Clean fuel line. 6. Blocked fuel line. Shooting 7. Wait a few minutes to restart, but do 7. Engi
Résumé du contenu de la page N° 17
7 Safety Labels � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Résumé du contenu de la page N° 18
3 5 31 4 32 34 33 35 2 1 6 27 7 30 28 29 27 8 9 26 15 22 17 23 21 14 25 16 17 18 14 24 18 15 14 19 16 20 10 12 11 13 18
Résumé du contenu de la page N° 19
8 1 710-1205 Eye Bolt 2 720-0279 Wing Nut 3 747-1161A Blade Control Handle Parts List 4 749-1092A Upper Handle 5 746-0957 Blade Control Cable - 37.25 inch 746-0946 Blade Control Cable - 48.25 inch 746-1130 Blade Control Cable - 40.00 inch 6 749-04037 Lower Handle 7 725-0157 Cable Tie 8 787-01097 Deck Assembly 22-inch 9 710-0654A TT Screw 3/8-16 x 1.0 10 748-0376C Blade Adapter To order replacement parts, call 1-800-800-7310 11 742-0642A Standard Blade 22-inch or visit us on the web at 12 736-
Résumé du contenu de la page N° 20
MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by MTD LLC with respect e. MTD does not extend any warranty for products sold or exported to new merchandise purchased and used in the United States, its outside of the United States, its possessions and territories, except possessions and territories. those sold through MTD’s authorized channels of export distribution. “MTD” warrants this product against defects in material and workman- f. Replacement parts tha
