Instruction d'utilisation Wright Manufacturing Roll Over Protective Structure 98210001

Résumé du contenu de la page N° 1

INSTALLATION & OPERATION MANUAL

Roll Over Protective Structure (ROPS)
Model 98210001

Wright Manufacturing, Inc.
2-Post folding ROPS assembly and mounting hardware


IMPORTANT!
READ INSTRUCTIONS CAREFULLY BEFORE OPERATION

Résumé du contenu de la page N° 2

PRINTED IN U.S.A. FORM NO. 98210012 07/02/07 INSTALLATION INSTRUCTIONS FOR ROLL-OVER PROTECTION SYSTEM (ROPS) This manual contains assembly, operating, maintenance and safety instructions for your ROPS. Before Installing the ROPS or operating a machine equipped with a ROPS, carefully read these instructions completely. The ROPS will reduce the risk of serious or fatal injury in the unlikely event of a tip over although the system cannot protect the operator from all possible

Résumé du contenu de la page N° 3

Parts list ITEM QTY PART NO. DESCRIPTION 1 1 98210002 WZ ROPS LEG WELDMENT, LH 2 1 98210003 WZ ROPS LEG WELDMENT, RH 3 1 98210004 WZ ROPS CENTER WELDMENT 4 1 98210005 WZ ROPS HARDWARE KIT 5 1 98210006 WZ ROPS SEAT BELT RETRACTOR 6 1 98210007 WZ ROPS SEAT BELT BUCKLE 7 8 11990093 HHCS, 7/16-14NC x 1.25 LG GR 5 8 8 12990009 HEX NYLOCK NUT, 7/16-14NC GR 5 9 4 13990002 FLAT WASHER, 7/16 10 2 3-10131 HHCS, 1/2-13NC x 3.00 LG GR 5 11 2 98210008 WZ ROPS LOCKING PIN 12 2 98210009 WZ ROPS

Résumé du contenu de la page N° 4

Machine Preparation 1. Park machine on a level surface and set brake. 2. Remove ROPS and hardware from shipping box and identify all parts using the parts list noted above. Lower ROPS Leg Tube Installation 3. Jack and secure rear of mower and remove rear tires. 4. Remove left side rear fuel tank bracket bolts. Support tank. 5. Place LH leg weldment against LH machine frame mounting location. 6. Secure using (3) 7/16-14NC x 1.25” long hex head bolts, (3) 7/16-14NC nylock hex nuts,

Résumé du contenu de la page N° 5

Upper ROPS Hoop Installation 10. Install upper roll bar hoop assembly. Secure each side of hoop with (1) ½-13NC x 3.00” long hex head bolt, (1) pin retainer washer and (1) ½-13NC center locking hex nut, into the upper mount hole of the hoop bracket. Tighten only until the nut makes contact with the hoop bracket. Do not over tighten. Hoop should pivot freely up and down. See Figure 3. 11. Install (1) EPDM washer onto each hitch pin. Position the top hoop into the up-right posi

Résumé du contenu de la page N° 6

13. Torque 7/16” lower leg mounting hardware to 59 ft-lbs and 3/8” hardware to 37 ft lbs. Seatbelt Installation 14. Secure retractable seat belt using (2) 7/16-14NC x 1.25” long hex head bolts, (4)7/16” flat washers and (2) 7/16-14NC nylock hex nuts. See figures 7 and 8. Figure 7 Figure 8 Wright Manufacturing, Inc. 4600X Wedgewood Boulevard Frederick, MD 21703 http://www.wrightmfg.com