Résumé du contenu de la page N° 1
59CL-4 & 59CLF-4
UNDERMOUNT
MOWER
Tested. Proven. Unbeatable.
29929
Rev. 3/28/2008
OPERATOR'S MANUAL
Résumé du contenu de la page N° 2
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration online at the Woods Dealer Website or complete the mail-in form included with the Operator’s Manual. If using the mail-in form, the dealer is to
Résumé du contenu de la page N° 3
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 OPERATION & SERVICE . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 4
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Make sure all safety decals are installed. Safety is a primary concern in the design and Replace if damaged. (See Safety Decals section for manufacture of our products. Unfortunately, our location.) efforts to provide safe equipment can be wiped Make sure shields and guards are properly out by an operator’s single careless act. installed and in good condition. Replace if damaged. In addition to the design and configuration of Insp
Résumé du contenu de la page N° 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Use extreme care and reduce ground speed on system leak down, hydraulic system failures, slopes and rough terrain. mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpect- Watch for hidden hazards on the terrain during edly and cause severe injury or death. Follow Oper- operation. ator's Manual instructions for working underneath Stop power unit and equipment immediately and blocking requi
Résumé du contenu de la page N° 6
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 1 - PN 19007 3 - SERIAL NUMBER PLATE MODEL NO. SERIAL NO. 2 - PN 53425 Woods Equipment Company Oregon, Illinois, U.S.A. DANGER BE CAREFUL! Use a clean, damp cloth to clean safety decals. ROTATING BLADES AND THROWN OBJECTS Avoid spraying too close to decals when using Do not put hands or feet under or into mower when a pressure washer; high-pressure water can engine is running. e
Résumé du contenu de la page N° 7
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 4 - PN 18877 5 - PN 18868 DANGER WARNING SHIELD MISSING TO AVOID SERIOUS Do not operate. Put shield on. INJURY OR DEATH: 18868-B Read Operator's Manual (available from dealer) and follow all safety precautions. Keep all shields in place and in good condition. 6 - PN 18869 DANGER Operate mower from tractor seat only. Lower mower, stop engine and remove SHIELD MISSING key bef
Résumé du contenu de la page N° 8
OPERATION & SERVICE necessary to make the belt run true. The side adjust- MOWING GRASS ment holes are also for additional belt takeup in case Woods mowers are equipped with suction-type blades belt adjustment is used on the idlers. It is very impor- which make them ideal for finish mowing large areas of tant to run the belt as much in line as possible at all lawn. times. The machine should be run level when mowing, and the uncut area kept to the left side (right side on left- Lubrication hand m
Résumé du contenu de la page N° 9
MOWER SPINDLE ASSEMBLIES CLEANING Mower spindles are equipped with two tapered roller After Each Use bearings. The proper adjustment is held by a spring ● Remove large debris such as clumps of dirt, grass, pin. It is not intended that these bearings be adjusted crop residue, etc. from machine. during their useful life. When difficulty is experienced ● Inspect machine and replace worn or damaged with the mower spindle assembly, time and trouble will parts. be saved by buying a completely new spin
Résumé du contenu de la page N° 10
ASSEMBLY Assembly of this mower is the responsibility of the Woods dealer. It should be delivered to the owner com- pletely assembled, lubricated, and adjusted for normal cutting conditions. Refer to mower frame assembly illustrations and parts list. Lay out parts and hardware on a clean surface to aid in assembly. AW ARNING ■ Keep all persons away from the operator con- trol area while performing adjustments, service or maintenance. Figure 1. Photo of Mounting Plate Supplied in 10570 A
Résumé du contenu de la page N° 11
cal push arms (31 and 40) and attachment brackets Belt Assembly & Adjustment (32) and (39). First put belt on bottom groove, right hand side of the center sheave. Then thread it to the left, around the left Idler Bracket Assembly (See Figure 9 & hand sheave. page 16) Remove the cap screws from the PTO bearing plate. Bolt the idler bracket assembly (36, 37, 38 and 45) to the tractor using 3/8 x 1-1/2" cap screws and lock washers. Sheave for Belt Pulley Shaft (See page 16) Remove paint from bore
Résumé du contenu de la page N° 12
It is assumed that the mower is adjusted to run approx- imately level. If the front of the mower is down, the idlers will have to be raised. If the back of the mower is down, the idlers will have to be down further. Belts must be in proper alignment with sheave grooves as shown in Figure 6 through Figure 8. PTO Pulleys PTO Pulleys must be moved in or out to cause the belt to be in alignment with the idlers. Belt Tension Run belts very tight. Slipping will heat and ruin a belt but tension is not
Résumé du contenu de la page N° 13
Wrong: Outer edge of belt appears to be in line. long slots. Remove side shields. Leave side skids on. If optional front roller has been installed, it must be removed. On mowers with bent-down front frame, remove center baffle and drill two 7/16 diameter holes in front of mower at the dimensions shown on page 21. Attach slotted angles (2) to leaf mulcher as shown in drawing. Place leaf mulcher over blades on mower. Attach angles (2) to mower side shields to side frame angle on Figure 8. Incorre
Résumé du contenu de la page N° 14
Figure 10. 59CL-4 Lift Assembly & Caster Assembly Photo 14 Assembly 29929 (Rev. 3/28/2008)
Résumé du contenu de la page N° 15
DEALER CHECK LISTS PRE-DELIVERY CHECK LIST DELIVERY CHECK (DEALER’S RESPONSIBILITY) (DEALER’S RESPONSIBILITY) Inspect the equipment thoroughly after assembly to ___ Instruct customer how to lubricate and explain importance of lubrication. ensure it is set up properly before delivering it to the customer. The following check lists are a reminder of ___ Point out the safety decals. Explain their meaning points to inspect. Check off each item as it is found sat- and the need to keep them in place a
Résumé du contenu de la page N° 16
59CL-4 & 59CLF-4 MAIN ASSEMBLY 53 - COMPLETE DECAL SET 61 - FRENCH SAFETY DECAL SET 29929 (Rev. 3/28/2008) 16 Parts
Résumé du contenu de la page N° 17
59CL-4 & 59CLF-4 MAIN ASSEMBLY NOTE: Mower frames sold after 1976 the front side of mower is formed down. Before they had a bolt-on front shield. Key For Number Used Columns A Serial Number 100 through 306 (59CL-1) C Serial Number 479 through 822 (59CL-3 & 59CLF-3) B Serial Number 307 through 478 (59CL-2) D Serial Number 823 and up (59CL-4 & 59CLF-4) REF PART A B C D DESCRIPTION REF PART A B C D DESCRIPTION 41 3493 - - 1 1 PTO Sheave, 1BK 6.1H 1 9700 1 1 1 1 Frame shipping unit 41A 1505 1 1 - -
Résumé du contenu de la page N° 18
59CL-4 & 59CLF-4 MAIN ASSEMBLY CONTINUED REF PART A B C D DESCRIPTION REF PART A B C D DESCRIPTION 95 12169 * 4 4 4 4 3/8 NC x 1-1/4 HHCS, GR5 85 738 * 4 4 - - 5/8 NC x 1-1/2 HHCS GR5 96 13258 - - 2 2 5/8 x 1-3/8 x 5/8 Flat washer 86 614 * 3 3 3 3 5/8 NC x 1-3/4 HHCS GR5 97 11900 * - - - 3 1/2 NC Flange lock nut 87 230 * 8 8 4 4 5/8 NC Hex nut 88 6239 * 1 1 1 1 5/8 Lock nut * Obtain locally 89 1286 * 8 8 12 12 5/8 Lock washer ** The 6760 casters may be used on “A”, “B”, & “C” 90 692 * 13 13 13
Résumé du contenu de la page N° 19
SPINDLE ASSEMBLY REF PART QTY DESCRIPTION 1 4116 1 Spindle 2 5089 2 Seal 3 41141Sleeve 4 41151Pin 5 4107 2 Bearing cone 6 4117 1 Housing with cups 7 4106 2 Bearing cup 8 1972 1 Grease fitting 9 4105 1 Spindle shaft 10 4110 1 Shoulder washer 11 6950KT 1 20-1/4 Medium suction blade 11 26559KT 1 20-1/4 Low suction blade 12 10658 1 5/8 NC x 1-1/2 Nylok bolt 13 3490 1 Blade bolt wrench 14 2974 1 Spindle lock wrench 16 10635 2 5/8 Cup washer 17 692 1 5/8 Flat washer 18 1015825 1 Blade bolt and washers
Résumé du contenu de la page N° 20
59 & L59 CASTERS REF PART QTY DESCRIPTION 1 29750 1 59 & L59 Right & left caster bundle 2 12243 1 Caster yoke (includes bolt, nut & 2 sleeves) 3 29746 (a) 1 Right caster arm asy, 13-5/32 long -or- 3 6761 (a) 1 Right caster arm, 16-5/32 long 4 29747 (a) 1 Left caster arm, 13-5/32 long -or- 4 18424 (a) 1 Left caster arm, 16-5/32 long 5 19703 1 8" HD Caster wheel with sleeve 7 2909 * 1 Straight 1/4 self-tapping grease fitting (for steel wheel) -or- 7 195 * 1 Straight 1/8P thread grease fitting (
