Résumé du contenu de la page N° 1
Safety Instructions & Operator’s Manual for
21” STEEL DECK
WALK MOWERS
SERIES 17
MODELS
R2167517BV
RP2167517BV
RP215517HC
RP2167517BVE
WRP216517BE
MODEL NUMBER EXPLANATION
R P 21 675 17 BV
MODEL DESIGNATION ENGINE DESIGNATION
SELF-PROPELLED SERIES DESIGNATION
CUTTING WIDTH ENGINE HORSE POWER
R – Recycling Model P – Self Propelled Model 17 – Series Designation
W – Model Designation 21 – 21” Cutting Width B – Briggs & Stratton H –
Résumé du contenu de la page N° 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
Résumé du contenu de la page N° 3
IMPORTANT SAFETY INSTRUCTIONS OPERATION MAINTENANCE AND STORAGE 1. DO NOT put hands or feet near or under 1. DO NOT store mower or fuel container inside rotating parts. Keep clear of discharge area where fumes may reach an open flame, spark or while engine is running. pilot light such as in a water heater, furnace, 2. STOP engine when crossing gravel drives, clothes dryer or other gas appliance. Allow walks, or roads, and under any conditions engine to cool before storing machine in a
Résumé du contenu de la page N° 4
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS...................................................................... 2 - 3 TABLE OF CONTENTS......................................................................................................4 SECTION 1 - FAMILIARIZATION.......................................................................................5 SECTION 2 - OPERATING INSTRUCTIONS............................................................... 6-10 Pre-start Checklist.........
Résumé du contenu de la page N° 5
Section 1 - FAMILIARIZATION BRIGGS HONDA ENGINE ENGINE BLADE WHEEL DRIVE CONTROL SPEED SPEED CONTROL CONTROL CONTROL GROUND SPEED CONTROL CHOKE FAST IGNITION KEY FAST ROPE START HANDLE SLOW SLOW FUEL FILLER CAP OIL FILL CAP AND DIPSTICK ENGINE PRIMER REAR HEIGHT ADJUSTMENT LATCH GRASS BAG ADAPTER FRONT HEIGHT ADJUSTMENT LATCHES FIGURE 1.1 1.1 INTRODUC
Résumé du contenu de la page N° 6
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.2 STARTING & OPERATION Make the following checks and perform the service 2.2.1. ENGINE & BLADE required before each start-up. (Primer Models) 2.1.1. Check guards, deflectors, grass bag, adapter 1. Move engine speed control to the “Fast” (Rabbit) and covers to make sure all are in place and position. See Figure 2.3. securely tightened. IMPORTANT: Certain models do not have a 2.1.2. Check blade control and wheel drive contro
Résumé du contenu de la page N° 7
Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION 5. After engine starts, allow a brief warm-up until 2.2.1. ENGINE & BLADE engine runs smooth. (Choke Models) 1. Move fuel shut off valve to the “ON” position. 2.2 STARTING & OPERATION See Figure 2.5. 2.2.1. ENGINE & BLADE (Electric Start Models) NOTE: Stop the engine (and blade) by releasing the When the ignition key (Electric Start Switch) is turned blade control. to “START”, the engine will not crank and will not s
Résumé du contenu de la page N° 8
Section 2 - OPERATING INSTRUCTIONS 2.4 HANDLE HEIGHT ADJUSTMENT 2.5 CUTTING HEIGHT ADJUSTMENT The height of the mower handle can be adjusted as 2. Set all wheels at the same cutting height. The follows: highest cutting position is Notch 6. The lowest 1. Loosen the lower nuts on each lower handle as cutting position is Notch 1. See Figure 2.10. shown in Figure 2.8. HIGHER LATCH LOWER POSITION HANDLE LOWER CUTTING HEIGHT SETTINGS LOOSEN LOWER NUTS ON EACH FIGURE 2.10 LOWER
Résumé du contenu de la page N° 9
Section 2 - OPERATING INSTRUCTIONS 2.8 INSTALLATION of RECYCLING PLUG WARNING (Optional Accessory on Some Models) DO NOT attempt any maintenance, adjustments or STEP 1: Once adapter has been installed, recycling may service with engine and blade running. STOP engine be desired. Insert recycling plug completely and securely and blade. Disconnect spark plug wire and secure into adapter. Install grass bag. See Figure 2.12. away from spark plug. Engine and components are HOT. Avoid se
Résumé du contenu de la page N° 10
Section 2 - OPERATING INSTRUCTIONS HOOK BAG HANDLE OVER LOWER WARNING HANDLES DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 2.9 INSTALLATION of GRASS CATCHER (Optional accessory on some models) SLIDE CONNECTOR OVER END OF ADAPTER FLANGE MIDDLE HAND
Résumé du contenu de la page N° 11
Section 2 - OPERATING INSTRUCTIONS 2.11 INSTALLATION of RECYCLING COVER WARNING (Optional Accessory on Some Models) DO NOT attempt any maintenance, adjustments or It will be necessary to remove bag adapter and grass service with engine and blade running. STOP bag or discharge deflector before installing recycling cover. See previous section for instructions. Install the engine and blade. Disconnect spark plug wire and recycling cover and secure to the side and top of the secure away
Résumé du contenu de la page N° 12
Section 3 – MAINTENANCE HONDA ENGINE 3.1 INTRODUCTION To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number. WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spar
Résumé du contenu de la page N° 13
Section 3 – MAINTENANCE 3.2.5. CHECK TRANSMISSION POLY-V BELT WARNING 1. Visually check poly-v belt for cracking, fraying, DO NOT attempt any maintenance, adjustments or severed or belt strands exposed. If worn or service with engine and blade running. STOP engine damaged, replace belt before operating mower. and blade. Disconnect spark plug wire and secure RECOMMENDED away from spark plug. Engine and components are BLADE RETAINING HOT. Avoid serious burns, allow sufficient time fo
Résumé du contenu de la page N° 14
Section 4 - REPAIR & ADJUSTMENTS 2. Replace the blade if it is badly chipped, bent, WARNING noticeably out of balance or has cracks or notch in DO NOT attempt any maintenance, adjustments or either tip. See Figure 4.1 & 4.1A. Replace with new service with engine and blade running. STOP engine blade. and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are WARNING HOT. Avoid serious burns, allow sufficient time for DO NOT use a cutting blade
Résumé du contenu de la page N° 15
Section 4 - REPAIR & ADJUSTMENTS CLUTCH CABLE WARNING DO NOT attempt any maintenance, adjustments or VINYL SPRING service with engine and blade running. STOP engine 1/16” TO 1/8” CLUTCH CABLE and blade. Disconnect spark plug wire and secure CLEARANCE EYE away from spark plug. Engine and components are UPPER SPRING HOT. Avoid serious burns, allow sufficient time for SPRING HOOK all components to cool. LOWER SPRING 4. Sharpen blade on a grinding wheel at an angle of 22 to 28 d
Résumé du contenu de la page N° 16
Section 4 - REPAIR & ADJUSTMENTS USE WARNING NEEDLE DO NOT attempt any maintenance, adjustments or NOSE PLIERS TO service with engine and blade running. STOP engine INSTALL and blade. Disconnect spark plug wire and secure DRIVE away from spark plug. Engine and components are SPRING HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3 DRIVEN AND DRIVE DISC SERVICE If the mower does not propel itself properly, See Figure 4.6. Check for the following
Résumé du contenu de la page N° 17
Section 4 - REPAIR & ADJUSTMENTS WARNING 1/8” MEASUREMENT TO OUTSIDE EDGE OF DRIVE DO NOT attempt any maintenance, adjustments or DISC service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure DRIVE SLIDE DRIVEN DISC away from spark plug. Engine and components are DISC ASSEMBLY HOT. Avoid serious burns, allow sufficient time for TOWARD OUTSIDE all components to cool. EDGE 4.3.3. DRIVEN DISC ADJUSTMENT TRANSFER ROD (Continued From Pr
Résumé du contenu de la page N° 18
Section 4 - REPAIR & ADJUSTMENTS 4.3.5. Replacing Bearing In Driven Disc Assembly WARNING IMPORTANT: The bearing, on these machines, is DO NOT attempt any maintenance, adjustments or staked into the thrust plate. The bearing will have to be driven out with a mallet and a large punch. A new service with engine and blade running. STOP engine bearing with four retaining screws will have to be and blade. Disconnect spark plug wire and secure purchased to replace existing bearing. away fr
Résumé du contenu de la page N° 19
Section 4 - REPAIR & ADJUSTMENTS 4.4 BELT SERVICE WARNING On self-propelled mowers, the engine belt transmits DO NOT attempt any maintenance, adjustments or power from engine to drive disc. The drive disc powers the poly-v belt, which engages the service with engine and blade running. STOP engine transmission that powers the rear wheels. Should and blade. Disconnect spark plug wire and secure these belts become worn, they could cause slippage, away from spark plug. Engine and compone
Résumé du contenu de la page N° 20
Section 4 - REPAIR & ADJUSTMENTS PULLEY POSITION WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure DRIVE DISC away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for SLOT IN END all components to cool. OF DRIVE DISC BOLT BUSHING 4.4.1. Engine Drive Belt Replacement (Stretch Type Belts) (Continued From Previo
