Résumé du contenu de la page N° 1
A AS SS SE EM MB BL LY Y I IN NS ST TR RU UC CT TI IO ON NS S
O OP PE ER RA AT TO OR R' 'S S M MA AN NU UA AL L
P PA AR RT TS S L LI IS ST T
Z Z
- -V VA AC C
Grass Catcher Kit
for CZT/HZT
Series 0
Models covered:
Actual product may differ from product pictured above
Blower Kit P/N 7078273
Bagger Kit P/N 0-50576
Weight Kit P/N 7078274
Complete Kit P/N 7063375
Manual No. 7100056 (I.R. 03/31/05)
Résumé du contenu de la page N° 2
1 preliminaries C Co on ng gr ra at tu ul la at ti io on ns s! ! You have just purchased one of the finest pieces of outdoor power equipment on the market today. If properly cared for, your new Z-Vac Grass Catcher Kit will provide years of dependable service. Please read and follow this instruction man- ual carefully in order to get the most out of your new equipment. As you carefully unpack your unit, you will find the following items: 1 Blower Kit 1 Bagger Kit 1 Weight Kit 1 Package containi
Résumé du contenu de la page N° 3
safety rules regarding outdoor power equipment 2 I IM MP PO OR RT TA AN NT T! ! R RE EA AD D C CA AR RE EF FU UL LL LY Y T TH HE E F FO OL LL LO OW WI IN NG G S SA AF FE ET TY Y R RU UL LE ES S B BE EF FO OR RE E A AS SS SE EM MB BL LI IN NG G O OR R O OP PE ER RA AT TI IN NG G U UN NI IT T. . engine before leaving unit. TRAINING -- Never operate with guards not securely in place. Be sure -- Read, understand, and follow all instructions in the man- all safety features are attac
Résumé du contenu de la page N° 4
2 safety rules regarding outdoor power equipment to cool before storing. CHILDREN -- Shut off fuel while storing or transporting. Do not store fuel Tragic accidents can occur if the operator is not alert to the near flames or drain indoors. presence of children. Children are often attracted to the unit -- Keep all hardware tight and keep all parts in good work- and its activity. Never assume that children will remain ing condition. Replace all worn or damaged decals. where you last saw them. --
Résumé du contenu de la page N° 5
unit assembly 3 BLOWER KIT INSTALLATION REMOVE PULLEY STEP 1: Remove pin, rod and spring securing dis- GUARD charge deflector to mower deck, and remove deflector. Store deflector for future use. IMPOR- TANT: Never operate any mower without a dis- charge deflector or grass catcher securely in place. STEP 2: Remove two bolts securing right deck pul- ley guard to mower deck and remove guard. Set bolts aside for future assembly step. Store guard REMOVE DEFLECTOR for future use. IMPORTANT: Never
Résumé du contenu de la page N° 6
3 unit assembly STEP 6a: Remove bolts securing impeller pulley cover to blower, and remove cover. REMOVE BOLTS, THEN REMOVE COVER STEP 6b: Check to see that blower belt is routed CHECK TO SEE around impeller pulley and idler pulleys after belt is THAT BELT IS installed onto deck pulley. Then replace cover. ON PULLEYS Tighten bolts securely. IMPORTANT: Never oper- ate any mower without a pulley guard securely in place. STEP 7: Slip tube of locking pin bracket into blow- INSERT er mount, and secur
Résumé du contenu de la page N° 7
unit assembly 3 STEP 9: Install belt guard between pulley guard and belt guard support clip on front part of blower mount. Secure with two 5/16 nylon wing nuts. Tighten nuts securely. INSTALL BELT GUARD AND SECURE WITH WING NUTS WEIGHT KIT INSTALLATION !! Warning: Weight kit must be installed prior to 4 NARROW BARS installing bagger unit. Failure to do so may THROUGH result in longitudal tipping of unit. FOOTREST STEP 10: Insert the four narrow weight bars through opening in side of foot re
Résumé du contenu de la page N° 8
3 unit assembly STEP 13: Hook bottom of bagger frame onto pins INSERT PIN INTO ROD in bottom of bumper mount plate. Then slide lock- SLIDE ROD ing rod through aligned holes in bagger frame and THROUGH HOLES bumper mount plate, securing with bridge pin. HOOK BAGGER FRAME ONTO BUMPER MOUNT PLATE PINS STEP 14: Install cross assembly onto bagger CROSS ASSEMBLY frame with four 3/8-16 x 3/4 bolts and hex flange lock nuts, tightening securely. Insert bolts back through bagger frame and into cross ass
Résumé du contenu de la page N° 9
unit assembly 3 STEP 18: Install bags onto cross assembly by SLIP SLOT IN GRASS hooking slot in bag hanger onto tabs in channel BAG HANGER ONTO assembly. TAB ON CROSS ASSEMBLY STEP 19: Close cover and lock in place by hook- ing lock knob into slot in cover latch arm. INSERT, THEN MOVE OVER AND UP TO LOCK STEP 20: Slip one hose clamp onto each end of CLAMP hose (use the clamp with the black quick-release WITH knob at the blower end), and install hose between NUT blower and bagger. Make sur
Résumé du contenu de la page N° 10
4 unit operation & maintenance INTRODUCTION WARNING ! ! Follow operation and maintenance instructions in the DO NOT attempt to remove any clogs from deck, blow- Operator’s Manual provided with the Snapper CZT/HZT. er, or hose with engine or blade running. STOP engine. STOP blades. Set brake. Remove key. Make sure GRASS CATCHER OPERATION blades and all rotating components have come to a 1. Select desired cutting height. Choose a setting that will complete stop before removing any catcher or unclo
Résumé du contenu de la page N° 11
unit operation & maintenance 4 IF THE GRASS CATCHER BECOMES CLOGGED 2. Catcher. Inspect all catcher components. Replace all (Continued From Previous Page) worn or damaged parts. 3. Catcher Bags. Check bags often for wear or damage. To Clear A Plugged Hose Replace worn or damaged bags immediately, using only 1. Stop blades. Stop engine. Remove key. SNAPPER approved replacement bags. 2. After all rotating components (engine, blower, blades) 4. Deck, Blower, Hose. Clean grass build up from deck
Résumé du contenu de la page N° 12
5 unit breakdown & parts list 12
Résumé du contenu de la page N° 13
unit breakdown & parts list 5 S Sn na ap pp pe er r Z Z- -V Va ac c B Bl lo ow we er r U Un ni it t G Gr ro ou up p - - C CZ ZT T / / H HZ ZT T M Mo od de el ls s Item Part No. Qty Description 1 3046782 1 WELDMENT, Blower Belt Guard 2 91121 1 NUT, 1/2-13 Hex Nyloc 3 90183 1 WASHER, 1/2" Flat SAE 4 3021097 1 PULLEY, AGroove Idler, Steel 5 44995 1 IDLER STUD (3/8-24 thread) 6 91804 2 FLATWASHER, 9/16 Type Narrow 7 14409 2 FLANGE BEARING, 9/16" I.D. (powdered metal) 8 10776 1 RETAINING
Résumé du contenu de la page N° 14
5 unit breakdown & parts list 14
Résumé du contenu de la page N° 15
unit breakdown & parts list 5 S Sn na ap pp pe er r Z Z- -V Va ac c B Bl lo ow we er r M Mo ou un nt t G Gr ro ou up p - - C CZ ZT T / / H HZ ZT T M Mo od de el ls s Item Part No. Qty Description 1 3036323 1 BELT, A Section, 91.125" effective length 2 3037161 1 WELDMENT, Belt Cover, Deck 3 ----- -- NOTUSED 4 91537 2 WING LOCKNUT5/16-18 5 3037162 1 BELTGUARD 6 3046806 1 PULLEY, Blower Input 7 78298 1 PULLEY, Spindle 8 3027505 1 WELDMENT, Blower Mount 9 3027507 1 WELDMENT, Guard Suppo
Résumé du contenu de la page N° 16
5 unit breakdown & parts list 16
Résumé du contenu de la page N° 17
unit breakdown & parts list 5 S Sn na ap pp pe er r Z Z- -V Va ac c C Ca at tc ch he er r G Gr ro ou up p - - C CZ ZT T / / H HZ ZT T M Mo od de el ls s Item Part No. Qty. Description 1 3046861 1 ASSEMBLY, 2 Bag Cover and Screen (includes Item No. 1a, 5, 12, 13, 14, 42, 43, 44, 45) 1a 1704033 1 CATCHER TOP, 2 Bag 2 1704180 2 WINDOW, Cover 3 1704405 1 DECAL, Safety, Grass Bag 4 1667248 6 CLIP, Canoe 5 1910531 4 WASHER, .188 Rivet 6 90922 1 SCREW, #10-32 x 1-1/2 Hex Washer Head Machine
Résumé du contenu de la page N° 18
5 unit breakdown & parts list 18
Résumé du contenu de la page N° 19
unit breakdown & parts list 5 S Sn na ap pp pe er r Z Z- -V Va ac c C Ca at tc ch he er r M Mo ou un nt t G Gr ro ou up p - - C CZ ZT T / / H HZ ZT T M Mo od de el ls s Item Part No. Qty. Description 1 3046687 1 WELDMENT, Bagger Mount Frame 2 91086 4 SCREW, 3/8-16 x 3/4" Hex Head Cap, GR5 3 91619 4 NUT, 3/8-16 Hex Flange Lock 4 3046831 1 ARM, Cover Latch 4a 3046829 1 REINFORCEMENTPLATE 5 91318 2 SCREW, 5/16-18 x 3/4" Hex Head Cap, GR5 6 91601 2 NUT, 5/16-18 Hex Flange Lock 7 3046995
Résumé du contenu de la page N° 20
5 unit breakdown & parts list 20
