Instruction d'utilisation GE r10279v

Résumé du contenu de la page N° 1

Design Guide with
Installation
Instructions
Wine Chiller, Wine Reserve
and Beverage Center
monogram.com

Résumé du contenu de la page N° 2

Safety Information BEFORE YOU BEGIN: WARNINGS: Read these instructions completely and carefully. • Use this appliance only for its intended purpose. • Immediately repair or replace electrical service cords IMPORTANT – Save these instructions that become frayed or damaged. for local inspector’s use. • Unplug the unit before cleaning or making repairs. • Repairs should be made by a qualified service IMPORTANT – Observe all governing codes technician. and ordinances. Note to Installer – Be sure to

Résumé du contenu de la page N° 3

Design Guide THE INSTALLATION SPACE PRODUCT CLEARANCES The stainless steel wine chiller, wine reserve and beverage center is factory set for a 110° door swing. Models that accept custom panels have a 95° door swing. Locate When installed in a corner: Outlet • Allow 4″ min. clearance on the hinge side for the 90° door 10-1/2" 24" swing and to allow racks to slide out. • Allow 10″ minimum clearance on the hinge side for a full 9" Max. 34-1/2"-35" 110° door swing. (Models ZDWI240WII and ZDBI2

Résumé du contenu de la page N° 4

Installation Instructions TOOLS REQUIRED STAINING WOOD DRAWER FRONTS • #2 Phillips screwdriver The drawer fronts are unfinished cherry wood. During • Adjustable wrench use, oil from hands may accumulate and stain the wood. • The drawer fronts may be stained and sealed to PARTS SUPPLIED match adjacent cabinetry. The tinted glass will make • Monogram nameplate the stained wood appear darker. A true color match • Hardware for changing door swing can be seen only when the door is opened. • Optional

Résumé du contenu de la page N° 5

Installation Instructions STEP 2 REVERSE DOOR SWING SKIP THIS STEP IF DOOR SWING SUITS THE INSTALLATION Install 3 Hinge Parts Included: Screws • Top left case hinge Remove • Bottom left case hinge Top Hinge • Left and right side decorative hinge cover • Decorative hinge screw hole cover ® • Torx driver bit Hinge Tools Required: Pin and • Phillips screwdriver Bracket • Electric drill Door Stop and Cam Riser Remove the door: • Flatten the shipping carton to use as a pad. • Remove the 2 screws an

Résumé du contenu de la page N° 6

Installation Instructions CUSTOM FRAME PANEL MODELS STEP 3 LEVEL Model ZDWI240WII and ZDBI240WII • Use an adjustable wrench to turn the leveling legs and These models require a custom panel frame surrounding raise or lower the product. the glass. There are two options: the panel may be 29-3/4″ • Adjust carefully; the product should be level and plumb or 30″ high. A 30″ panel requires a notch cut into the bottom with cabinetry, and should align with adjacent toekick of the panel to avoid interf

Résumé du contenu de la page N° 7

ZTBSS1 Monogram Tubular Handle Kit BEFORE YOU BEGIN: TOOLS AND MATERIALS REQUIRED • Gloves to protect against sharp edges Read these instructions completely and carefully. • #2 Phillips screwdriver • Drill and 1/4″ bit and 1/2″ spade bit IMPORTANT – Save these instructions • Safety glasses for local inspector’s use. • Center punch • Pencil IMPORTANT – Observe all governing codes and ordinances. Note to Installer – Be sure to leave these THIS KIT INCLUDES instructions with the Consumer. • Tubular

Résumé du contenu de la page N° 8

TEMPLATE FOR NAMEPLATE LOCATION Cut on Dotted Line Upper Left Upper Right Top of Glass Door Corner of Corner of Glass if Hinge Glass if Hinge Top of Badge is on Left is on Right Door Frame Side Door Frame Side DOOR NAMEPLATE LOCATION To position nameplate: • Cut template along dotted line. • Hold or tape template behind glass door so that it is visible from the front side. • Remove backing from nameplate. • Place nameplate onto front side of door, matching illustration on the template. IMPORTANT