Résumé du contenu de la page N° 11
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. Never use choke to stop engine. HOW TO USE YOUR TRACTOR IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "OFF" WILL CAUSE THE TO SET PARKING BRAKE (See
Résumé du contenu de la page N° 12
OPERATION For best cutting performance, grass over 6 inches in "ENGAGED" POSITION height should be mowed twice. Make the first cut ATTACHMENT relatively high; the second to desired height. LIFT LEVER HIGH POSITION TO ADJUST GAUGE WHEELS (See Fig. 7) ATTACHMENT Gauge wheels are properly adjusted when they are slightly CLUTCH LEVER LOW "DISENGAGED" off the ground when mower is at the desired cutting height in POSITION POSITION operating position. Gauge wheels then keep the deck in proper posit
Résumé du contenu de la page N° 13
OPERATION CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to sepa- ration and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions f
Résumé du contenu de la page N° 14
OPERATION Slowly move motion control lever forward, after the AUTOMATIC TRANSMISSION WARM UP tractor moves approximately five (5) feet, slowly move Before driving the unit in cold weather, the transmission motion control lever to reverse position. After the tractor should be warmed up as follows: moves approximately five (5) feet return the motion Be sure the tractor is on level ground. control lever to the neutral (N) position. Repeat this Place the motion control lever in neutral. Rele
Résumé du contenu de la page N° 15
OPERATION MULCHING MOWING TIPS MAX 1/3 IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN AFTER EACH USE. The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best r
Résumé du contenu de la page N° 16
CUSTOMER RESPONSIBILITIES MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES Check Brake Operation Check Tire Pressure Check Operator Presence and Interlock Systems T R Check for Loose Fasteners 5 A Sharpen/Replace Mower Blades 3 C Lubrication Chart T Check Battery Level 4 0 Clean Battery and Terminals R Check Transaxle Cooling Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (without oil filter) 1,2 E Clean Air Filter N
Résumé du contenu de la page N° 1
02478
183113 Rev. 1 3.19.02 RD
Printed in U.S.A.
Résumé du contenu de la page N° 2
SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Avoid starting or stopping on a slope. If tires lose traction, I. GENERAL OPERATION disengage the blades and proceed slowly straight down • Read, understand, and follow all instructions in the manual the slope. and on the machine before starting. On
Résumé du contenu de la page N° 3
SAFETY RULES Safe Operation Practices for Ride-On Mowers Look for this symbol to point out im- portant safety precautions. It means Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED. Never carry passengers or children even with the blades off. Do not mow in reverse unless absolutely necessary. Al- CAUTION: In order to prevent acciden- ways look down and behind before and while backing. ta
Résumé du contenu de la page N° 4
CONGRATULATIONS on your purchase of a new Tractor. PRODUCT SPECIFICATIONS It has been designed, engineered and manufactured to give GASOLINE CAPACITY 2.0 GALLONS you the best possible dependability and performance. AND TYPE: UNLEADED REGULAR Should you experience any problem you cannot easily remedy, please contact your nearest authorized service OIL TYPE (API-SF-SJ): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) center. We have competent, well-trained technicians and the proper tools to service
Résumé du contenu de la page N° 17
CUSTOMER RESPONSIBILITIES TRACTOR MANDREL TRAILING ASSEMBLY EDGE UP Always observe safety rules when performing any mainte- BLADE nance. CENTER HOLE BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual). LOCK WASHER STAR TIRES Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual). FLAT WASHER
Résumé du contenu de la page N° 18
CUSTOMER RESPONSIBILITIES BATTERY SAE VISCOSITY GRADES Your tractor has a battery charging system which is suffi- SAE 30 cient for normal use. However, periodic charging of the 5W-30 battery with an automotive charger will extend its life. -20 0 30 32 40 60 80 100 Keep battery and terminals clean. F C -30 -20 0 -10 10 20 30 40 Keep battery bolts tight. TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE Keep small vent holes open. FIG. 14 Recharge at 6-10 amperes for 1 hour. NOTE:
Résumé du contenu de la page N° 19
CUSTOMER RESPONSIBILITIES ENGINE OIL FILTER CLEAN AIR SCREEN Replace the engine oil filter every season or every other oil Air screen must be kept free of dirt and chaff to prevent change if the tractor is used more than 100 hours in one year. engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. MUFFLER CLEAN AIR INTAKE/COOLING AREAS Inspect and replace corroded muffler and spark arrester (if To insure proper cooling, make sure
Résumé du contenu de la page N° 20
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: Depress clutch/brake pedal fully and set parking brake. Place motion control lever in neutral (N) position. Place attachment clutch in “DISENGAGED” position. Turn ignition key to “STOP” and remove key. Make sure the blades and all moving parts have completely stopped. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TRACTOR IMPO
Résumé du contenu de la page N° 5
UNASSEMBLED PARTS Seat Steering Wheel Steering Wheel Insert (1) Washer 17/32 x 1-3/16 x 12 Gauge (1) Knob Steering Extension Shaft Steering Sleeve Slope Sheet Steering Adapter (1) Large Flat Washer (1) Oil Drain Tube (1) Locknut 1/2-20 (2) Keys (2) Mulch Blades (1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut 1/4-28 5
Résumé du contenu de la page N° 6
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY INSERT A socket wrench set will make assembly easier. Standard wrench sizes are listed. Utility knife Pliers 1/2 HEX NUT (1) 3/4" wrenches Tire pressure gauge
Résumé du contenu de la page N° 7
ASSEMBLY NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the SEAT PAN tractor from the skid. LABEL TO ROLL TRACTOR OFF SKID (See Operation section, page 10, for location and function of controls) Press lift lever plunger and raise attachment lift lever to its highest position. Release parking brake by depressing clutch/brake pedal. Place freewheel control in freewheeling position to disengage transmission (See “TO TRANSPORT” in
Résumé du contenu de la page N° 8
ASSEMBLY CHECK TIRE PRESSURE IMPORTANT: FOR SHIPPING PURPOSES, THE MULCHER PLATE WAS PREATTACHED TO YOUR The tires on your tractor were overinflated at the factory for MOWER. THE MULCHER PLATE MUST ONLY BE USED shipping purposes. Correct tire pressure is important for best cutting performance. WITH THE MULCHING BLADES THAT CAME PACKED SEPARATELY IN THE CARTON. Reduce tire pressure to PSI shown in “PRODUCT SPECIFICATIONS” section of this manual. YOUR MOWER CAME FACTORY EQUIPPED WITH HIGH PERFO
Résumé du contenu de la page N° 9
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR REVERSE FORWARD FAST SLOW WARNING LIGHTS ON OVER TEMP ENGINE ON ENGINE OFF OIL PRESSURE LIGHT PARKING BRAKE UNLOCKED MOWER LIFT FUEL CHOKE MOWER HEIGHT LOCKED P ATTACHMENT REVERSE NEUTRAL HIGH LOW PARKING BRAKE CLUTCH ENGAGED 15 15 15 KEEP AREA CLEAR SLOPE HAZARDS ATTACHMENT (SEE SAFETY RULES SECTION) CLUTCH DISENGAGED IGNITION FREE WHEEL DANG
Résumé du contenu de la page N° 10
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. LIGHT IGNITION ATTACHMENT SWITCH SWITCH CLUTCH LEVER AMMETER POSITION CHOKE CONTROL LIFT LEVER PLUNGER THROTTLE CONTROL ATTACHMENT LIFT LEVER CLUTCH/BRAKE PEDAL HEIGHT ADJUSTMENT KNOB PARKING BRAKE MOTION FREE WHEEL CONTROL CONTROL LEVE
