Résumé du contenu de la page N° 1
IMPORTANT MANUAL Do Not Throw Away
03076
OWNER'S MANUAL
WARNING:
MODEL:
Read this Man u al and follow all Warnings
and Safety Instructions. Fail ure to do so can
re sult in serious in ju ry.
PB19542LT
LAWN TRACTOR
ALWAYS WEAR EYE PROTECTION DURING OPERATION
Visit our website: www.poulan-pro.com
411188 Rev 7 04.28.08 SBW/TH Printed in U.S.A.
Résumé du contenu de la page N° 2
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and WARNING: In order to prevent ac ci - working. den tal starting when setting up, trans- • Slow down before turning. port ing, ad just ing
Résumé du contenu de la page N° 3
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN GENERAL SERVICE Tragic accidents can occur if the operator is not alert to • Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the equipment the presence of children. Children are often attracted to the ma chine and the mowing activity. Never assume that is in safe working condition. • Never tamper with safety devices. Check their proper children will remain where you last saw them. • Kee
Résumé du contenu de la page N° 4
CONGRATULATIONS on your purchase of a new tractor. PRODUCT SPECIFICATIONS It has been designed, engineered and manu fac tured to give you the best possible dependability and performance. Gasoline Capacity 1.50 Gallons and Type: Unleaded Regular Should you experience any problem you cannot easily rem- Oil Type (API-SG-SL): SAE 30 (above 32°F) edy, please contact your nearest authorized service center/ SAE 5W-30 (below 32°F) department. We have com pe tent, well-trained tech ni cians a
Résumé du contenu de la page N° 5
CONTENTS OF HARDWARE PACK Slope Sheet Slope Sheet Key Key (1) Oil Drain Tube (1) Oil Drain Tube (2) Keys (2) Keys (1) Hex Bolt Steering Steering Extension Extension Insert Shaft Shaft Lock Washer Se Sea at t Steering Steering Extension Extension Washer Shaft Shaft Steering Wheel Steering Steering Boot Boot Washer Steering Wheel Steering Wheel Adapter Adapter 5
Résumé du contenu de la page N° 6
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Stan dard wrench sizes are listed. INSERT 5/16 HEX BOLT (1) 1/2" wrench Utility knife (2) 3/4" wrench Tire
Résumé du contenu de la page N° 7
ASSEMBLY INSTALL SEAT (See Figs. 2 and 3) CHECK BATTERY (See Fig. 4) • Remove bolt and flat washer se cur ing seat to cardboard • Lift seat pan to raised position. packing and set aside for as sem bly of seat to tractor. • If this battery is put into service after month and year Remove the cardboard packing and discard. indicated on label (label located between terminals) • Connect switch to seat. charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of
Résumé du contenu de la page N° 8
ASSEMBLY TO DRIVE TRACTOR OFF SKID (See Op- ✓CHECKLIST er a tion section for location and func tion of BEFORE YOU OPERATE YOUR NEW TRAC TOR, WE con trols) WISH TO ASSURE THAT YOU RECEIVE THE BEST PER- FOR MANCE AND SAT IS FAC TION FROM THIS QUALITY • Be sure all the above assembly steps have been com- PROD UCT. plet ed. • Check engine oil level and fill fuel tank with gasoline. PLEASE REVIEW THE FOLLOWING CHECKLIST: • Sit on seat in operating position, depress clutch/brake ✓ All assembl
Résumé du contenu de la page N° 9
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. FAST SLOW REVERSE NEUTRAL HIGH LOW CHOKE IGNITION SWITCH P ENGINE ON ENGINE START PARKING BRAKE ENGINE OFF REVERSE PARKING BRAKE PARKING BRAKE OPERATION LOCKED UNLOCKED SYSTEM (ROS) FUEL OIL PRESSURE BATTERY REVERSE FORWARD OVER TEMP MOWER HEIGHT MOWER LIFT LIGHT 15 15 ATTACHMENT ATTACHMENT SLOPE HAZARDS CLUTCH ENGAGED DANGER, KEEP HANDS KEEP AREA CLEAR CLUTCH DIS
Résumé du contenu de la page N° 10
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. LIGHT SWITCH ATTACHMENT ROS "ON" POSITION CLUTCH LEVER THROTTLE/CHOKE CONTROL PARKING BRAKE IGNITION SWITCH GEAR SHIFT CLUTCH/BRAKE LEVER PEDAL ATTACHMENT LIFT LEVER FIG. 5 Our tractors conform to the applicable safety standards o
Résumé du contenu de la page N° 11
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. NOTE: Under certain conditions when tractor is standing HOW TO USE YOUR TRACTOR idle with the engine running, hot engine exhaust gases may cause “brown ing”
Résumé du contenu de la page N° 12
OPERATION USING THE REVERSE OPERATION SYSTEM - TO ADJUST MOWER CUT TING HEIGHT • Depress clutch/brake pedal all the way down and (See Fig. 7) hold. The po si tion of the at tach ment lift le ver (A) de ter mines the • With engine running, turn ignition key counterclockwise cut ting height. to ROS "ON" position. • Look down and behind before backing. • Move gear shift lever to reverse (R) po si tion and slowly release clutch/brake pedal to start movement. • When use of the ROS is no longer n
Résumé du contenu de la page N° 13
OPERATION TO OPERATE ON HILLS ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. WARNING: Do not drive up or down Use fresh, clean, regular un lead ed gasoline with a hills with slopes great er than 15° and minimum of 87 octane. (Use of leaded gasoline will do not drive across any slope. increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel • Choose the slowest speed before starting up or down in quan ti
Résumé du contenu de la page N° 14
OPERATION COLD WEATHER STARTING ( 50° F and below) • When engine starts, allow engine to run with the throttle control in the choke ( ) position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the tem- per a ture. • The attachments can also be used during the engine warm-up period. NOTE: If at a high altitude (above 3000 feet) or in cold tem per a tures (below 32 F
Résumé du contenu de la page N° 15
maint_sch-tractore.ROS.e MAINTENANCE BEFORE EVERY EVERY EVERY EVERY EVERY BEFORE MAINTENANCE EACH 8 25 50 100 SEASON STORAGE SCHEDULE USE HOURS HOURS HOURS HOURS Check Brake Operation Check Tire Pressure T Check Operator Presence & ROS Systems R Check for Loose Fasteners A Check/Replace Mower Blades 3 C T Lubrication Chart 0 Check Battery Level 4 R Clean Battery and Terminals Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level 1,2 Change Engine Oil (with oil filte
Résumé du contenu de la page N° 16
02545 MAINTENANCE BLADE CARE TRACTOR For best results mower blades must be kept sharp. Re place Always observe safety rules when per form ing any main- bent or damaged blades. te nance. BRAKE OPERATION CAUTION: Use only a replacement blade If tractor requires more than five (5) feet to stop at highest approved by the manufacturer of your tractor. Using a blade not approved speed in high est gear on a level, dry concrete or paved by the manufacturer of your tractor is surface, then brake
Résumé du contenu de la page N° 17
MAINTENANCE • Slide blade on to an unthreaded portion of the steel bolt SAE VISCOSITY GRADES or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal SAE 30 position. If either end of the blade moves downward, 5W-30 sharpen the heavy end until the blade is balanced. -20 0 30 32 40 60 80 100 F C -30 -20 -10 0 10 20 30 40 CENTER HOLE TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE oil_visc_chart1_e FIG. 12 BLADE 5/8" BOLT NOTE: A
Résumé du contenu de la page N° 18
MAINTENANCE CLEAN AIR SCREEN IN-LINE FUEL FILTER (See Fig. 14) Air screen must be kept free of dirt and chaff to prevent The fuel filter should be replaced once each season. If fuel engine dam age from overheating. Clean with a wire brush filter becomes clogged, ob struct ing fuel flow to car bu re tor, or com pressed air to re move dirt and stubborn dried gum re place ment is re quired. fibers. • With engine cool, remove filter and plug fuel line sec- tions. AIR FILTER • Place new fuel f
Résumé du contenu de la page N° 19
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SE RI OUS IN JU RY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift lever in neutral (N) position. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. IMPORTAN
Résumé du contenu de la page N° 20
SERVICE AND ADJUSTMENTS • ATTACH FRONT LINK (E) - Work from left side of trac- tor. Insert rod end of link assembly through front hole in tractor front suspension bracket (F). A • Insert end of link (E) into hole in front mower bracket and secure with washer and retainer spring (J). E B FIG. 16 • ATTACH REAR LIFT LINKS (C) - Lift rear corner of J mower and position slot in link assembly over pin (D) F on rear mower bracket and secure with washer and retainer spring. H FIG. 18 • Hook end of
