Résumé du contenu de la page N° 1
Back-UPS
Installation Guide
™
Back-UPS BE750G Series
Inventory Safety
This UPS is intended for indoor use only.
Do not operate this UPS in direct sunlight, in
contact with fluids, or where there is
excessive dust or humidity.
Be sure the air vents on the UPS are not
blocked. Allow adequate space for proper
ventilation.
The battery typically lasts for two to five years. Environmental factors impact
battery life. Elevated ambient temperatures, poor quality utility power, and frequent
shor
Résumé du contenu de la page N° 2
Connect the Battery The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop! Connect the Battery” label that covers the outlets. Prior to connecting any equipment to the unit, connect the battery cable to the unused battery terminal. It is normal for small sparks to be seen when the battery cable is connected to the battery terminal. Press the battery compartment cover Connect the battery cable securely Reinstall the battery compartment release tab located on the r
Résumé du contenu de la page N° 3
Connect Modem/Telephone/DSL/FAX/10/100 Base-T Network Cable The Back-UPS protects a single line, 2 wire telephone line, including a Digital Subscriber Line (DSL), a Cable In Cable Out Circuit Breaker modem, a 10/100 Base-T ethernet, or a FAX machine Push to Reset from power surges when connected through the Network/DSL/Modem/FAX Back-UPS coaxial connectors. Building PowerChute In CAUTION-Refer to bottom Out Wiring Fault of unit for safety markings. USB Port ™ PowerChute Personal Edition Sof
Résumé du contenu de la page N° 4
Turn On the Back-UPS Press the Power ON button located on the top of the Back-UPS. The Power On/Replace Battery LED will illuminate green and a single short beep will be audible to indicate that the Back-UPS is providing protection for connected equipment. The Back-UPS battery charges fully during the first 16 hours while connected to utility power. The Back-UPS battery will charge while the Back-UPS is switched on or off and is connected to utility power. Do not expect full battery run capa
Résumé du contenu de la page N° 5
Status Indicators Audible Indicator Status LED Indicator Audible Indicator On Terminates Power On The green LED illuminates. None N/A The Back-UPS is supplying utility power to connected equipment. On Battery The green LED illuminates.The Back-UPS beeps 4 times every Beeping stops when utility Back-UPS supplying battery LED is not illuminated during 30 seconds. power is restored or the power to battery backup outlets. the beeps. Back-UPS is turned off. Low Battery warning The green LED illu
Résumé du contenu de la page N° 6
Voltage Sensitivity Adjustment The Back-UPS detects and reacts to line voltage distortions by transferring to battery backup power to protect connected equipment. In situations where either the Back-UPS or the connected equipment is too sensitive for the input voltage level it is necessary to adjust the transfer voltage setting. 1. Connect the Back-UPS to a wall outlet. The Back-UPS will be in Standby mode, no indicators will be illuminated. 2. Press and hold the ON/OFF button for 10 seconds.
Résumé du contenu de la page N° 7
Troubleshooting Problem and Possible Cause Solution The Back-UPS will not turn on The Back-UPS has not been turned on. Press the POWER ON button. The Back-UPS is not connected to utility power, there is no Make sure the power cord is securely connected to the wall outlet, utility power available at the wall outlet, or the utility power and that there is utility power available at the wall outlet.Where is experiencing a brownout or over voltage condition. applicable, check that the wall outlet
Résumé du contenu de la page N° 8
Replace Battery Use only approved APC replacement battery cartridge. Deliver used batteries to a battery replacement facility in the packaging provided by APC with the replacement battery cartridge. To order replacement battery cartridges contact APC through the Web site www.apc.com. Warranty The standard warranty is 3 years in the USA and Canada, 2 years in all other regions from the date of purchase. APC standard procedure is to replace the original unit with a factory reconditioned unit. Cu
