Résumé du contenu de la page N° 1
¤
Agri-Fab
OWNERS
MANUAL
Model No.
45-03072
45-03611
42" ROUGH CUT
CAUTION:
TRAILMOWER
Read Rules for
Safe Operation
and Instructions
• Safety
Carefully
• Assembly
• Operation
• Maintenance
• Parts
the fastest way to purchase parts www.speedepart.com
PRINTED IN U.S.A. FORM NO. 49464 (5/04)
Résumé du contenu de la page N° 2
TABLE OF CONTENTS SAFETY RULES ...................................................... 3,4 SAFETY AND OPERATIONAL DECALS ................ 5,6 HARDWARE CHART .................................................. 7 ASSEMBLY ............................................................ 8-11 OPERATION.........................................................12-16 CUSTOMER RESPONSIBILITIES...................... 17-20 STORAGE ................................................................. 21 REPAIR PARTS
Résumé du contenu de la page N° 3
3
Résumé du contenu de la page N° 4
4
Résumé du contenu de la page N° 5
5
Résumé du contenu de la page N° 6
6
Résumé du contenu de la page N° 7
CONTENTS OF PARTS BAG SHOWN FULL SIZE A B C D E H F G I J NOT SHOWN FULL SIZE K REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION A 1 Hex Bolt, 1/2" x 7" G 2 Hex Lock Nut, 3/8" B 2 Hex Bolt, 3/8" x 2-3/4" H 2 Hex Lock Nut, 5/16" C 2 Hex Bolt, 5/16" x 3/4" I 1 Hex Lock Nut, 1/4" D 1 Hex Bolt, 1/4" x 3/4" J 2 Flat Washer, 3/8" E 3 Screw, Self Tapping #10 x 1/2" K 3 Clip, 3/8" F 1 Hex Lock Nut, 1/2" 7
Résumé du contenu de la page N° 8
ASSEMBLY INSTALL WIRE HARNESS TO ENGINE • Feed Wire Harness up through hole in middle of Front Drive Cover. • Install one Wire to Engine Magneto Ground Terminal. (The same Terminal as red Wire from inside Mower.) • Install other Wire of Wire Harness to Engine Ground Base. (The same Terminal as black Wire from inside Mower.) • Refasten Front Drive Cover to mower housing. INSTALL CLUTCH TO TOWBAR TUBE • Place Clutch Cable forward along Towbar Tube. • Spread ends of three Cable Clips and place arou
Résumé du contenu de la page N° 9
ASSEMBLY ENGINE MAGNETO GROUND (RED WIRE) ENGINE GROUND BASE FEED WIRE HARNESS THROUGH THIS HOLE FRONT DRIVE COVER REAR QUADRANT 3/8 X 2-3/4 HEX BOLT CLUTCH LEVER 3/8 FLAT WASHER #10 SCREW (3) CLUTCH CABLE CABLE CLIPS (3) TOW BAR TUBE 3/8 HEX LOCK NUT CABLE GUIDE 3/8 FLAT WASHER 1/4 X 3/4 HEX BOLT HITCH ASSEMBLY CLUTCH CABLE 5/16 HEX NUT (2) MOUNTING ANCHOR 1/4" HEX LOCK NUT FIG. 1 9
Résumé du contenu de la page N° 10
ASSEMBLY INNER NUT CLUTCH CABLE ADJUSTMENT • Remove four screws from Rear Drive Cover. Lay aside cover and screws. • Place Clutch Lever in "DISENGAGED" position • The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from OUTER NUT the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" po
Résumé du contenu de la page N° 11
ASSEMBLY INSTALL REAR ROLLER TO DECK • Install Rear Roller Mounting Bracket to rear of deck using two 5/16 x 3/4 Hex Bolts and two 5/16 Hex Lock Nuts. (See Fig. 3.) • Install Roller to Rear Roller Bracket using 1/2 x 7 Hex Bolt and 1/2 Hex Lock Nut. • Make sure Roller turns freely on Bolt. 5/16 X 3/4 HEX BOLTS AND 5/16 HEX LOCK NUTS REAR ROLLER MOUNTING BRACKET ROLLER 1/2 X 7 HEX BOLT 1/2 HEX LOCK NUT FIG. 3 11
Résumé du contenu de la page N° 12
OPERATION RECOIL START HANDLE HEIGHT ADJUSTMENT STRAP HEIGHT ADJUSTMENT MOWER BLADE LIFT LEVER CLUTCH LEVER TOW HITCH OFFSET SHUT OFF ADJUSTMENT CONTROL TOW BAR HEIGHT ADJUSTMENT FIG. 4 12
Résumé du contenu de la page N° 13
OPERATION 13
Résumé du contenu de la page N° 14
OPERATION HAIR COTTER PIN HEIGHT ADJUSTMENT STRAP LOCATING PIN HEIGHT ADJUSTMENT HAIR COTTER PIN LIFT LEVER CUTTING CLEVIS PIN HEIGHTS 1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 4-1/2" 5" TOW BAR TOW BAR ADJUSTMENT CUTTING HEIGHT GROUND LEVEL FIG. 6 14
Résumé du contenu de la page N° 15
OPERATION This mower has been designed to run offset from the center of the tow vehicle. This allows the operator to drive along side high brush with the tow vehicle while cutting down the brush beside him. The adjustable hitch gives you three offset cutting positions plus straight behind for narrow paths. MODEL 45-03071 The adjustable hitch of this mower can be set in seven positions including straight and offsets of 15", 29" and 39" on both sides. MODEL 45-0361 The adjustable hitch of this mow
Résumé du contenu de la page N° 16
OPERATION 16
Résumé du contenu de la page N° 17
CUSTOMER RESPONSIBILITIES WHEEL PIVOT 3 WHEEL 2 SPINDLE 2 SWIVEL 2 QUADRANT 3 WHEEL PIVOT 3 WHEEL 2 17
Résumé du contenu de la page N° 18
CUSTOMER RESPONSIBILITIES BLADE CARE AND SERVICE BLADE ASSEMBLY CAUTION: DO NOT HANDLE MOWER BLADES WITH BARE HANDS. CARELESS OR IMPROPER HANDLING MAY RESULT IN SERIOUS INJURY. BLADE CARE For best results mower blades must be kept sharp. The blades can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen blades while they are still on the mower. BLADE SERVICE (Refer to fig. 9) TO REMOVE BLADE ASSEMBLY FROM DECK • Remove cotter pin from the spindle shaft. • Remove nut and w
Résumé du contenu de la page N° 19
CUSTOMER RESPONSIBILITIES INNER NUT CLUTCH CABLE ADJUSTMENT CL • Remove four screws from Rear Drive Cover. Lay aside • cover and screws. • Place Clutch Lever in "DISENGAGED" position • • The Cable should be under slight tension but should • not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from NO OUTER NUT the switch body, the cable tension is too tight and the the Engine will not start. Eng TO INCREASE CABLE TENSION TO • Place B
Résumé du contenu de la page N° 20
CUSTOMER RESPONSIBILITIES INSTALLING NEW V-BELT V-BELT REPLACEMENT • V-belt must be replaced if it becomes stretched to the point that it can no longer be adjusted, or if it • Feed new V-belt between the two belt guides at the becomes frayed or otherwise can not function Engine Pulley. properly. • Place V-belt up and around the Engine Pulley. Check • Move Blade Clutch Lever to the "DISENGAGED" to make sure the V-belt is seated properly in the position. groove of the Engine Pulley. • Place V-belt
