Résumé du contenu de la page N° 1
INSTALLATION MANUAL
COLOR GPS/PLOTTER
GP-1650W/1650WD
SYSTEM CONFIGURATION.................................................................................. i
EQUIPMENT LISTS .............................................................................................. ii
1. INSTALLATION................................................................................................. 1
1.1 Installation of Display Unit .......................................................................
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
SAFETY INSTRUCTIONS Safety Instructions for the Installer CAUTION WARNING Do not work inside the Ground the equipment to equipment unless totally prevent electrical shock familiar with electrical and mutual interference. circuits. Confirm that the power supply voltage Hazardous voltage which can is compatible with the voltage rating shock, burn or cause serious of the equipment. injury exists inside the equip- ment. Connection to the wrong power supply can cause fire or equipment damage. T
Résumé du contenu de la page N° 4
Résumé du contenu de la page N° 5
SYSTEM CONFIGURATION The GP-1650W/1650WD mainly consists of a display unit and a GPS antenna. A DGPS beacon receiver is provided inside the display unit for GP-1650WD type. The chart card drive in the display unit loads electronic charts. External equipment which may be connected include an autopilot and a DGPS beacon receiver. GPA-019 (for GP-1650WD) GPA-017 (for GP-1650W) Antenna unit Receives signal from GPS satellite and beacon reference station (GP-1650WD only). Display unit Ship's p
Résumé du contenu de la page N° 6
EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks Display Unit GP-1650W - 1 GP-1650WD - Antenna UnitG- PA-017 for GP-1650W 1 GPA-019 for GP-1650WD Spare Parts* SP14-02401 004-374-630 1 Installation CP14-05100 000-041-480 1 Materials* FP14-02301 004-375-830 1 Hard cover Accessories* screws for hanger, FP14-02302 004-375-850 1 screws for flush mount *: Refer to Packing list at the end of this manual. Optional equipment Name Type Code No. Remarks GR-7000A-1650-10N-019 000-0
Résumé du contenu de la page N° 7
EQUIPMENT LISTS Optional equipment (con’t) Name Type Code No. Remarks PR-62 000-013-484 for 100 VAC 2.5GY5/1.5NT#5 PR-62 000-013-485 for 110 VAC 2.5GY5/1.5NT#5 Rectifier PR-62 000-013-486 for 220 VAC 2.5GY5/1.5NT#5 PR-62 000-013-487 for 230 VAC 2.5GY5/1.5NT#5 MJ-A6SPF0007-100 000-125-237 MJ-A6SPF0012-100 000-133-817 Cable Assy. MJ-A6SPF0012-050 000-134-424 MJ-A6SPF0011-050 000-132-244 MJ-A6SPF0011-100 000-132-336 RAM Card 00RAM02MC-004 004-371-790 2MB C-MAP 1650/1850-MAP 004-376-420 modifi
Résumé du contenu de la page N° 8
EQUIPMENT LISTS This page is intentionally left blank. iv
Résumé du contenu de la page N° 9
1. INSTALLATION 1.1 Installation of Display Unit Mounting considerations The display unit can be installed on a tabletop, on the overhead or flush mounted in a console or panel. Hard Cover Tabletop Overhead Tabletop, overhead mounting methods When selecting a mounting location for the display unit keep the following in mind: • Keep the display unit out of direct sunlight. • The temperature and humidity should be moderate and stable. • Locate the unit away from exhaust pipes and vents
Résumé du contenu de la page N° 10
WARNING 1. INSTALLATION Mounting procedure Follow the procedure below to mount the display unit on a tabletop or the overhead. Tabletop, overhead mounting 1. Fix the hanger by four pan head screws 5 X 16. 2. Screw knob bolts in display unit, set it to hanger, and tighten knob bolts. 3. Attach hard cover to protect LCD. Tabletop, overhead mounting of display unit Flush mounting Note: Use supplied pan head screws when the thickness of the bulkhead is from 11 to 14 mm. For bulkh
Résumé du contenu de la page N° 11
1. INSTALLATION 216±1 6-R2.25 164±0.5 Pan head screws 4.5 Flush mount Flush mounting of display unit 1.2 Installation of Antenna Unit Mounting considerations Install the antenna unit referring to the installation diagram on page D-3 or D-4. When selecting a mounting location for the antenna unit, keep in mind the following points: • Select a location out of the radar beam. The radar beam will obstruct or prevent reception of the GPS satellite signal. • The location should be well
Résumé du contenu de la page N° 12
2. WIRING All wiring are terminated at the rear of the display unit. Earth terminal Displa unit GPA-017 (GP-1650W) Antenna unit + 13GND 2 - 12-24 VDC ANT XDR DGPS NMEA External equipment GPA-019 (GP-1650WD) DGPS beacon receiver White Black (option for GP-1650W, Shield RS-232C only) Display unit, rear view Power cable Connect the power cable to the power connector. Connect the leads to the battery (12 or 24 VDC); white to plus(+) terminal and black to minus(-) terminal. Cable connect
Résumé du contenu de la page N° 13
2. WIRING Antenna unit Connect the antenna unit cable to the ANT connector. Ground The display unit contains several CPUs. While they are operating, they radiate noise, which can interfere with radio equipment. Ground the unit to prevent interference. The grounding wire should be 1.25 sq or larger and as short as possible. Connect the grounding wire to ship's ground. On a fiberglass boat, it is best to install a ground plate that measures about 20 cm by 30 cm on the outside of the
Résumé du contenu de la page N° 14
2. WIRING Extension cable line-up (in case of 15m, 30 m or 50 m) Fabricate the end of the antenna cable and attach the coaxial connector. Details are shown on the next page. Antenna unit GPA-019S/GPA-017S : Connector Conversion cable assy. Antenna cable To display unit 1 m 30 m or 50 m 1 m Fabricate locally. (See the next page.) Cable extension (CP20-01700, CP20-01710) Antenna unit GPA-019S/GPA-017S : Connector Antenna cable To display unit 15 m Cable extension (TNC-PS-3D-15) W
Résumé du contenu de la page N° 15
2. WIRING How to attach the N-P-8DFB connector Dimensions in millimeters. Outer sheath Armor Inner sheath shield Remove outer sheath and armor by the dimensions shown left. 50 30 Expose inner sheath and shield by the dimensions shown left. Cover with heat-shrink tubing and heat. Cut off insulator and core by 10mm. 10 30 Twist shield end. Ship on clamp nut, gasket and clamp as shown left. Clamp Clamp Gasket nut (reddish brown) Aluminum foil Fold back shield over clamp and trim. Trim shiel
Résumé du contenu de la page N° 16
3. INITIAL SETTINGS 3.1 NMEA Setting NMEA port This setting should be done when connecting with other equipment, autopilot, radar or remote display. 1. Press the [MENU] key. 2. Press the CONFIGURATION soft key. 3. Press the SETUP NMEA PORT1 soft key. 4. Press the cursor pad to select FORMAT. 5. Press the EDIT soft key to display the following window. SETUP OUTPUT FORMAT PORT1 NMEA0183 Ver1.5 NMEA0183 Ver2.0 ENTER CANCEL DGPS 3D Output format window (PORT 1) 6.
Résumé du contenu de la page N° 17
3. INITIAL SETTINGS DGPS port Set the following when connecting with DGPS beacon receiver GR-80 or the DGPS beacon receiver is incorporated, PC to the DGPS port. Note: Signal level for DGPS port is RS232C. 1. Press the [MENU] key. 2. Press the CONFIGURATION soft key. 3. Press the SETUP NMEA/DGPS PORT 2 soft key. 4. Select FORMAT, and then press the EDIT soft key. The following window appears. SETUP FORMAT OUTPUT FORMA NMEA 0183 T PORT2 VER 1.5 NMEA0183 Ver
Résumé du contenu de la page N° 18
3. INITIAL SETTINGS 3.2 Output Data Sentences Select output data sentences for external equipment as follows. 1. Press the [MENU] key. 2. Press the CONFIGURATION soft key. 3. Press the SETUP NMEA PORT1 soft key. 4. Press the SELECT SNTNC. soft key to display the SELECT SENTENCE window. SELECT SELECT SENTENCE SNTNC. AAM APB ON ON/OFF BOD BWR* GGA GLL ON RMA RMB ON RMC ON VTG ON WPL XTE ZDA ON RETURN DGPS 3D *: BWR for Rhumb line BWC for Great circle Select sentence window
Résumé du contenu de la page N° 19
3. INITIAL SETTINGS Input/Output data sentences Port Format Data Remarks WPL: GP only Input TLL*1, MTW, WPL*1, DBT/DPT NMEA Ver 1.5: DBT NMEA Ver 2.0: DPT NMEA-0183 NMEA Ver. 2.0 AAM, APB, BOD, BWC/BWR, Ver. 1.5 GGA, GLL, RMA, RMB, RMC, GREAT CIRCLE: BWC Output IEC1162 VTG, WPL, XTE, ZDA, MTW, RHUMB LINE: BWR GTD*2 WPL: GP only Input TLL*1, MTW, WPL*1, DBT/DPT NMEA Ver 1.5: DBT NMEA-0183 NMEA Ver 2.0: DPT Ver. 2.0 DGPS Ver. 1.5 AAM, APB, BOD, BWC/BWR, RS232C GREAT CIRCLE: BWC GGA, GLL, RMA
Résumé du contenu de la page N° 20
3. INITIAL SETTINGS 3.4 DGPS Setting When external DGPS beacon receiver (RS-232C only) is connected or the DGPS beacon receiver is incorporated, set the DGPS mode referring to the following procedure. 1. Press the [MENU] key. 2. Press the GPS/DGPS/TD OPTIONS soft key. 3. Press the DGPS/WAAS SETUP OPTIONS soft key. DGPS FORMAT NMEA 0183 WAAS DGPS/WAAS MODE OFF VER 1.5 BEACON FREQUENCY AUTO BEACON BAUD RATE AUTO WAAS SEARCH AUTO EDIT CORRECTION DATA SET 02 DGPS/WAAS ALARM ON RETUR
