Instruction d'utilisation Gamber Johnson CF-31

Résumé du contenu de la page N° 1

INSTALLATION INSTRUCTIONS
Product Revision Form
INST-509
7160-0318-00 THROUGH 7160-0318-12 Rev. G
PANASONIC TOUGHBOOK CF-31 MAG DOCKING STATION
Printing Spec: PS-001
This instruction sheet is for the following products:
Panasonic Toughbook CF-31 docking station with No integrated
high gain antenna pass-thru cables.
Item No. 7160-0318-00 (-P) (Button lock, No RF)
Item No. 7160-
0318-04 (-P) (Button lock, No RF, Int. power)
Item No. 7160-0318-07 (-P) (Auto lock, No RF)
Item No. 7160-0318-10 (-P)

Résumé du contenu de la page N° 2

CF-31 DOCKING STATION FEATURE IDENTIFICATION Alignment Pin Docking Connector External Antenna Connectors Interlock Pin Alignment Pin USB Port Front Retainer Docking Indicator LED Docking Handle Push Button / Auto Lock Wireless Antenna Switch Video Connection (WWAN Antenna) External Microphone Serial 2 Serial 1 DC In External Speaker or Headphones WLAN/GPS Antenna Connector Ethernet Port #2 Ethernet Port #1 WWAN Antenna Connector USB Ports Cable Restraint Bracket Kensington Lock Slot Pg 2

Résumé du contenu de la page N° 3

IMPORTANT SAFETY INFORMATION FOR INSTALLERS Safety is dependent on the proper installation and servicing of this docking station. It is important to read and follow all instructions before installing this product. To properly install a Gamber-Johnson docking station you must have a good understanding of automotive electrical procedures and systems, along with proficiency in the installation and service of aftermarket vehicle equipment. There are no adjustments required at any time of the electri

Résumé du contenu de la page N° 4

MOUNTING THE DOCKING STATION Mount docking station to mounting system using the four 1/4-20 UNC mounting holes on the bottom of the dock. Four 1/4-20 UNC x .50 Button Head Mounting Screws are provided in the hardware bag. *Recommended torque: 75 in-lbs. Over tightening mounting hardware may damage docking station. *Use of hardware longer than 5/8" may damage docking station. This docking station is designed to be used with a variety of Gamber-Johnson mounting systems. Installation instructions

Résumé du contenu de la page N° 5

WIRELESS ANTENNA SWITCH Wireless Antenna Switch If wanting to use external antenna, connected by cable "EXT" / "INT" to the WAN port on the dock: Position the switch toward the "EXT" side (Figure 2). If wanting to use antenna built into the computer or a PC Card type antenna: Position the switch toward the "INT" side (Figure 2). CF-31 MK1 computers are not effected by the "Antenna Switch". To disable external antenna use on all CF31-MK1 computers, install Panasonic service part # [DFHR3S

Résumé du contenu de la page N° 6

POWER SUPPLY INFORMATION (NON INTERNAL POWER SUPPLY MODELS) Panasonic recommends using a Lind Auto Adapter (Lind part number PA1580-2961) to power the docking station. It can be ordered from Gamber-Johnson (part number 14103) or directly from Lind Electronics, Minneapolis, Minnesota (952-927-6303). Installation of the Power Jack: Remove the #8-32 screw and the Power Cable Cover on the bottom of the dock (Figure 4). Attach the Power Cable Pull Strap (located in the hardware bag) to the power jac

Résumé du contenu de la page N° 7

DOCKING THE COMPUTER 1. Shut down the computer. 2. Make sure the sliding door (located on the on the back of the computer) has been fully opened, exposing the computer's docking connector. (Figure 8) 3. Set computer in the dock: a. Hook the front of the computer on the front retainer (Figure 9). b. Lower the back of the computer onto the Alignment Pins (Figure 9). Figure 8 c. Lightly press down on the back of the computer Sliding Door to ensu

Résumé du contenu de la page N° 8

REMOVING COMPUTER FROM THE DOCK 1. Shut down computer. 2. Auto Lock: Insert key and rotate clockwise. Button Lock: Unlock with key if locked. Push button in until lever releases. 3. Lift the back of the computer off of the locating pins. 4. Lift the computer out from under the Front Retainer. DOCKING INDICATOR LED With computer installed in the dock, the Docking Indicator LED, located on the right side of the dock, can be used as a troubleshooting tool (Figure 11). GREEN: All ports are read