Instruction d'utilisation Gamber Johnson 7160-0264-02

Résumé du contenu de la page N° 1

INSTALLATION INSTRUCTIONS
Product Revision Form
INST-372
PANASONIC CF19 DOCKING STATIONS, Rev. H
CRADLE and ACCESSORIES
7160-0207: Docking Station (NO/RF) 7160-0215: LED Assembly
7160-0207-02: Docking Station (DUAL/RF) 7160-0049: CF19 Screen Support
7160-0264-00 (-P): MK4 Docking Station (NO/RF) 7160-0073: CF19 Wedge
7160-0264-02 (-P): MK4 Docking Station (DUAL/RF)
7160-0264-03 (-P): MK4 Docking Station w/Power Adapter (NO/RF)
7160-0264-04 (-P): MK4 Docking Station w/Power Adapter (DUAL

Résumé du contenu de la page N° 2

External PANASONIC CF19 DOCK Antenna Top View Connectors Toughbook Certified Label Vibration See Sheet 1 for computer Damper compatibilitty statement Alignment Latch Pin Mechanism Multi I/O Latch Connector Front Security Lock Alignment Guide Vibration Damper Vibration USB Port Damper Power ON LED Alignment Vibration Pin Front Damper Alignment Guide Back View WLAN/GPS WWAN Antenna Antenna Connector Connector DC In RJ45 External Connection Microphone External Speakers or Headphones Serial Video US

Résumé du contenu de la page N° 3

Installation of the Power Jack: Remove the #6-32unc x .1/4" long scew that attaches the Power Cable Cover to the outside of the dock (fig 1). Attach the Power Cable Pull Strap (located in hardware bag) to the power jack (fig 2). Plug the power jack into the input jack located on the port replicator board and tuck the pull strap into the electrical box (fig 3). Replace the Power Cable Cover to hold the power jack in place (fig 4). Remove fig 1 fig 2 fig 3 fig 4 #6-32 x 1/4-in screw & power ca

Résumé du contenu de la page N° 4

ReLocating Computer Carrying Strap The CF19 computer is supplied, from Panasonic, with a carrying strap attached to the back edge of the computer case. The computer can be installed into the dock with the strap attached to the back or front edge, but the strap will need to be unhooked when installed on the front of the comptuer, allowing each end of the strap to hang down over the sides of the dock. If the strap is not unhooked it will interfere with the docks' latching mechanism. Important: If

Résumé du contenu de la page N° 5

Cable Ties Cable Ties Cables are attached to ports on the back of the dock. Cable ties and cable tie holders are provided to secure the cables to the dock. Press the cable tie holder into the mounting holes on the dock. Insert the cable tie through the tie holder and tighten the cable tie around the cables as needed. DOCKING INDICATOR LED With computer installed in the dock, the Docking Indicator LED, located on the right side of the dock, can be used as a troubleshooting tool. GREEN: All ports

Résumé du contenu de la page N° 6

CF19 Accessories Screen Support 7160-0049: CF19 Screen Support #8-32 X .38 Screws and Flat Washers Use two #8-32 x .38 long socket head screws and two #8 flat washers to attach the screen support to the back side of the CF19 Dock as shown. 7160-0073: Work Table Wedge The CF19 work table wedge has rubber pads to provide a mobile slip free mounting surface. Four .281 square holes on the bottom surface allow mounting the work table wedge permanently to a surface if required. See drawing for mounti

Résumé du contenu de la page N° 7

LED Assembly 7160-0215: LED Assembly Activation Button Position the LED assembly over two holes in the back cover, and attach using the #6-32unc x .38 screws that were provided with the LED assembly. The LED is powered using the red and black wires on the back of the light base. The LED Assembly is designed to operate on 12volts DC. In a negative ground vehicle: #6-32 x .38 Screws Connect the RED wire to the positive pole of the The LED has three light options: White, vehicle battery or power d