Résumé du contenu de la page N° 1
ORDER NO. CPD0811210CE
Notebook Computer
Model No. CF-19KDRAXCM
This is the Service Manual for
the following areas.
M …for U.S.A. and Canada
© Panasonic Corporation 2008.
Unauthorized copying and distribution is a violation of law.
Résumé du contenu de la page N° 2
WARNING For U.K. This apparatus must be earthed for your safety. To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connec- tion to earth. Wrongly wired extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power poi
Résumé du contenu de la page N° 3
LASER SAFETY INFORMATION . For U.S.A Class 1 LASER-Product This product is certified to comply with DHHS Rules 21 CFR Subchapter J. This product complies with European Standard EN60825 (or IEC Publication 825) For all areas This equipment is classified as a class 1 level LASER product and there is no hazardous LASER radiation. Caution: (1) Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. (2) The drive is de
Résumé du contenu de la page N° 4
SAFETY PRECAUTIONS 1. Before servicing, unplug the power cord to prevent an electric shock. 2. When replacing parts, use only manufacture's recommended components for safety. 3. Check the condition of the power cord. Replace if wear or damage is evident. 4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc. Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to
Résumé du contenu de la page N° 5
Precautions (Battery Pack) When the Battery Pack Has Become Degraded, Do Not Use with Any Other Product Replace It with a New One The battery pack is rechargeable and was intended for Continued use of a degraded b ttery pack may generate the specified product. If it is used with a product other a high levels of heat, cause a fire to start and cause the than the one for which it was designed, electrolyte leak- pack to burst or explode. age, generation of heat, ignition or rupture may result. Do
Résumé du contenu de la page N° 6
CONTENTS 1. Specifications 1-1 2. Names and Functions of Parts 2-1 3. Block Diagram 3-1 4. Diagnosis Procedure 4-1 5. Power-On Self Test (Boot Check) 5-1 6. List of Error Codes 6-1 7. Self Diagnosis Test 7-1 8. Wiring Connection Diagram 8-1 9. Disassembly/Reassembly 9-1 10. Exploded View 10-1 11. Replacement Parts List 11-1
Résumé du contenu de la page N° 7
1. Specifications To check the model number: Check the bottom of the computer or the box the computer came in at the time of purchase. To check CPU speed, memory size and the hard disk drive (HDD) size: Run the Setup Utility ( Reference Manual “Setup Utility”) and select [Information] menu. [CPU Speed]: CPU speed, [System Memory]: Memory size, [Hard Disk]: Hard disk drive size cations Model No. CF-19KDRAXJM CF-19KDRAXCM *1 CPU Intel® Core™ 2 Duo Processor SU9300 (1.20 , 3 L2 cache, 800 FSB
Résumé du contenu de la page N° 8
cations Operation Environment Temperature: 5 °C to 35 °C {41 °F to 95 °F} Humidity: 30% to 80% RH (No condensation) Storage Environment Temperature: -20 °C to 60 °C {-4 °F to 140 °F} Humidity: 30% to 90% RH (No condensation) Operating System ® Windows Vista Business Service Pack 1 ® ® Microsoft Windows XP Professional Service Pack 2 with Advanced Security Technologies (NTFS File System) ® ® Microsoft Windows XP Tablet PC Edition 2005 (NTFS File System) *8 Utility Programs Adobe Reader, PC Info
Résumé du contenu de la page N° 9
*13 SD Memory Cards that support high-speed transfer rates can be used. Windows ReadyBoost function is also supported. to 8 GB. Operation on other SD equipment is not guaranteed. This computer is not compatible with MultiMediaCards. Do not insert this type of cards. *14 Theoretical value and not the actual speed. The transfer rate does not become higher even if you use a card that supports the higher transfer rate. *15 Varies depending on the usage conditions. *16 2 Measured at LCD bri
Résumé du contenu de la page N° 10
2. Names and Functions of Parts A: Wireless LAN Antenna G: Bluetooth Antenna Reference Manual “Wireless LAN” Reference Manual “Bluetooth” B: Stylus/Digitizer pen Holder H: Display Release Latch C: Touch Pad page 12 “Switching to the Tablet mode” D: LED Indicator I: Speaker : Wireless ready Reference Manual “Key Combinations” This indicator lights when Wireless LAN, Blue- J: Function Key tooth, and/or Wireless WAN are co
Résumé du contenu de la page N° 11
Left side Rear side Bottom A: DC-IN Jack When recording in stereo using a stereo microphone: B: USB Port Click (Start) - [Control Panel] - [Hardware and Reference Manual “USB Devices” Sound] - [Sound] - [Recording] - [Microphone] - C: IEEE 1394 Interface Connector [Properties], and then add a check mark for [No Au- Reference Manual “IEEE 1394 Devices” dio Enhancements] in [Microphone Enhancements]. D: Modem Port Reference Manual
Résumé du contenu de la page N° 12
3 Block Diagram 3-1 Intel® Core 2 ™ Duo mobile processor U7500 iint nt ll e e (Ultra Low Voltage 1.06GHz) L1 cache: Internal 64K bytes each core M Me er rom UL om ULV V L2 cache: Internal 2M bytes D Dual core ual core For Santa Rosa 1.05V Audio Board Processor side Bus 64bit 533MHz LCD LCD AMP Speaker Internal DRAM 10.4 10.4” 64bit BUS 1.8V 533MHz RJ11 Main Memory DDR2 533 Graphics Interface X XGA GA 1GB CRT SW Sound Headphone 965-GM Sigmatel Data Modem SO-DIMM Extensi
Résumé du contenu de la page N° 13
4 Diagnosis Procedure 4.1. Basic Procedures 4-1
Résumé du contenu de la page N° 14
4.2. Troubleshooting Please take note of the following two points with regard to troubleshooting: 1. Know-how of diagnosis upon occurrence of heavy troubles, e.g. Set cannot be turned ON, Set fails to start, No display on screen , etc. 2. Explanation of each trouble, mainly symptom of trouble in operation. Flow Chart Pay attention to the following points when in pursuit of the cause of a troubleshooting. 1. Peripheral apparatus connected with the set should all be removed before opera
Résumé du contenu de la page N° 15
5 Power-On Self Test (Boot Check) Outline of POST The set has a boot check function called POST (Power-On Self Test) in it. The condition of the main body is diagnosed by checking beep sound or error code. Start .............Test begins automatically when power switch is set to ON. Normal finish .....After memory checking, a beep sound is issued once and the set is placed into automatic stop. Note: If no error occurs, nothing is displayed. (No display of OK, etc.) Error Diagnosis by Checkin
Résumé du contenu de la page N° 16
6 List of Error Codes The following is a list of the messages that BIOS can display. Most of them occur during POST. Some of them display information about a hardware device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it has been configured. Following the list are explanations of the messages and remedies for reported problems. If your system displays one of except the messages marked below wi
Résumé du contenu de la page N° 17
02D0 System cache error - Cache disabled Contact Panasonic Technical Support. 02F0: CPU ID: CPU socket number for Multi-Processor error. 02F4: EISA CMOS not writable ServerBIOS2 test error: Cannot write to EISA CMOS. 02F5: DMA Test Failed ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers. 02F6: Software NMI Failed ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt). 02F7: Fail - Safe Timer NMI Failed ServerBIOS2 test error: Fail
Résumé du contenu de la page N° 18
7 Self Diagnosis Test As for the self-diagnosis test(PC-Diagnostic utility) to use this model, a standard test and the enhancing test by the module of the main body building in are possible. NotesTo skip BIOS password Use + key to skip BIOS password or authentication of fingerprint. This key is only for entering DIAG mode. Not available to boot the computer. If customer set "HDD Lock", the DIAG program cannot perform HDD test. *This key is for serv
Résumé du contenu de la page N° 19
2. Operation of PC-Diagnostic Utility -Only the device which can be inspected on the entire screen is displayed. -The item does not appear when the device of wireless LAN etc. is not physically connected. -The movement of the item must use an arrow key or a flat pad. -As for the device under the diagnosis, blue and yellow are alternately displayed at the left of the icon. - The diagnosis result of the device greens at the left of the icon when it is normal, and becomes red when abnormal. -When t
Résumé du contenu de la page N° 20
2-1. Selection of tested device -To test only a specific device, "Test" and "Do not test" of each device can be selected. -The device which can select the enhancing test changes in order of "The standard is tested" and "Do not test" whenever the device icon is clicked. Start the standard test Do not test Please begin testing clicking if the selection of the tested device ends.
