Résumé du contenu de la page N° 1
A
4 6 8 7
B
APPENDIX
E
Installing the Wall Mount for the Cisco Unified
IP Phone 6901 and 6911
This appendix contains information on installing the wall mount for use with the Cisco Unified IP Phone
6901 and 6911 phones.
Installing a Wall Mount for the Cisco Unified IP Phone 6901
The following section describes how to install the Wall Mount plate for use with the
Cisco Unified IP Phone 6901.
Cisco recommends that you use the Leviton Wall Mount plate (Leviton type number: 4108W-0SP) for
moun
Résumé du contenu de la page N° 2
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6901 Before You Begin Before you mount the phone on the wall, ensure that the handset rest is such that the receiver will not slip out of the cradle (Figure E-2). Figure E-2 Preparing the Handset Hookswitch 1 2 3 4 1 Remove the handset from the cradle and pull the plastic tab from the handset rest. 2 Rotate the tab 180 degrees. 3 Hold the tab betwee
Résumé du contenu de la page N° 3
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6901 Installing the Phone on Wall Mount Plate To install the phone on the wall mount plate, follow these steps: Procedure Step 1 Plug the telephone line cord (RJ45 connector) into the phone jack at the base of the phone (Figure E-3). Figure E-3 RJ45 Connector in the Phone Jack 2 1 1 Network Port on the Phone 2 RJ45 Connector Cisco Unified IP Phone 69
Résumé du contenu de la page N° 4
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6901 Step 2 Plug the RJ45 connector into the wall mount phone jack (Figure E-4). Figure E-4 RJ45 Connector in the Wall Mount Jack 2 3 1 4 1 Network Port on the Phone 3 Wall Mount Plate 2 RJ45 Connector 4 Network Port on the Wall Mount Plate Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP an
Résumé du contenu de la page N° 5
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6901 Step 3 Slip the mounting holes on the base of the wall mount plate and over the wall mount pins (Figure E-5). Figure E-5 Mounting Holes 1 2 1 Mounting Hole on the Phone 2 Wall Mount Pin on the Wall Mount Plate Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP) OL-24582-01 E-5 253
Résumé du contenu de la page N° 6
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6901 Step 4 Firmly slide the IP Phone down into place (Figure E-6). Figure E-6 Sliding the IP Phone Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP) E-6 OL-24582-01 253658
Résumé du contenu de la page N° 7
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6911 The following section describes how to install the wall mount for use with the Cisco Unified IP Phone 6911. Figure E-7 shows a list of items included in the Wall Mount Kit for the Cisco Unified IP Phone 6911. Figure E-7 Wall Mount Kit for Cisco Unified IP Phone 6911 Screws Anchors Mach
Résumé du contenu de la page N° 8
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6911 Installing the Bracket To install the phone on the wall, follow these steps: Procedure Step 1 Mount the wall bracket in the desired location (Figure E-8). You can install the wall bracket over an Ethernet jack, or you can run the Ethernet network cable to a jack nearby. a. Use the Level to ensure the wall bracket is level, then use a pencil to
Résumé du contenu de la page N° 9
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6911 Figure E-8 Mounting the Wall Bracket A B Mark mounting Level wall holes through bracket on wall bracket on wall C D Screw bracket to wall using Phillips head Insert anchors into wall screws Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP) OL-24582-01 E-9 274936
Résumé du contenu de la page N° 10
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6911 Step 2 Attach the phone bracket to the IP Phone (Figure E-9). a. Detach the handset cord (and headset cord, if there is a headset), power cord, and any other attached cords from the base of the phone. b. Remove the label covers that are concealing the screw holes. c. Attach the phone bracket by inserting the tabs into the mounting tabs on the p
Résumé du contenu de la page N° 11
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6911 Step 3 Remove the handset wall hookswitch in the handset rest, rotate the hookswitch by 180 degrees, and reinsert the hookswitch. The hookswitch should have a lip on which the handset catches when the phone is vertical (Figure E-10). Figure E-10 Preparing the Handset Hookswitch 1 2 3 4 Cisco Unified IP Phone 6901 and 6911 Administration Guide
Résumé du contenu de la page N° 12
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6911 Step 4 Attach the Ethernet cable to the 10/100 SW network port and wall jack. If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100 PC access port. If you are using an external power supply, plug the power cord into the phone and dress the cord by clipping it into the clips incorporated into t
Résumé du contenu de la page N° 13
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6911 Step 5 Attach the phone to the wall bracket by inserting the tabs on the top of the phone bracket into the slots on the wall bracket. Ensure that the power cord and any other cable that does not terminate in the wall behind the bracket are positioned in one of the cable-access openings in the bottom of the bracket. The phone and wall brackets
Résumé du contenu de la page N° 14
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911 Installing a Wall Mount for the Cisco Unified IP Phone 6911 Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP) E-14 OL-24582-01
