Résumé du contenu de la page N° 1
FK1459 P0109YI
JK-1MD
HANDS FREE COLOR VIDEO INTERCOM
MASTER MONITOR STATION
INTERPHONE VIDEO COULEUR MAINS LIBRES
MONITEUR MAÎTRE
VIDEO INTERCOMUNICADOR A COLOR MANOS LIBRES
APARATO PRINCIPAL CON MONITOR
HANDENVRIJE KLEURENVIDEOFONIE
MONITOR-HOOFDPOST
VIDEOCITOFONO A COLORI A VIVAVOCE
POSTAZIONE DI MONITORAGGIO PRINCIPALE
JK-1MD
Master monitor station
Moniteur maître
Aparato principal con monitor
Monitor-hoofdpost
Postazione di monitoraggio
principale
INSTALLATION & OPERATION MANUAL
MANUEL D’
Résumé du contenu de la page N° 2
PRECAUTIONS General Prohibitions Prohibition to Dismantle the Unit Prohibition on Subjecting the Unit to Water General Precautions WARNING General Precautions 1. Keep the unit more than 1 m away from radio or TV set. (Negligence could result in death or serious injury.) 2. This unit is for indoor use only. Do not use outdoors. 1. High voltage is present internally. Do not open the case. Electric shock could result. 3. In areas where broadcasting station antennas are close by, the intercom sys
Résumé du contenu de la page N° 3
English Français Español Nederlands Italiano INSTALLATION 2 2-1 Mounting locations Install the master monitor station in a place The master monitor station has switches on Allow 15 cm (6") or more of vertical open 1 2 3 where the screen is not exposed to direct both sides. Allow at least 5 cm (2") of open space from the center of the mounting sunlight. space on either side. bracket in order to mount the master monitor station. JK-1MD / JK-1HD 3 2 + 15 cm + 5 cm + 5 cm (6") (2") (2") 2-2
Résumé du contenu de la page N° 4
MOUNTING 3 Back wiring Mounting screws x 2 UP 1-gang box JK-1MD 83.5 mm (3-5/16") Mounting bracket 1. Press RELEASE button (to insert or remove the wire). 1 2. Insert the cable into the terminal. 2 8 mm (3/8") Surface wiring * W hen a 1-gang box is not mounted, the cable can be routed as surface wiring to the top or bottom PS-1820 PS-1810DIN/ of the unit. Cut a cable inlet on the upper part of the unit to allow passage of the wiring into the unit. PS-1820DIN Mounting bracket * T o pass th
Résumé du contenu de la page N° 5
English Français Español Nederlands Italiano WIRING 4 Insert wires securely into each terminal as shown. JK-1MD JK-1HD Sub master Video door station DOOR monitor station Master monitor station 2 JK-1MD NP JK-1HD JK-DA 2 2 P P PS18 PS18 JK-DV JK-DVF When the JK-1HD is connected, split power between the master station and the sub master station if radio signals A1 A2 are picked up during communication. 2 Optional call extension NP speaker IER-2 OP 2 2 NP + - (To optional units) NP 2 P 2 Pr
Résumé du contenu de la page N° 6
NAMES 5 Color LCD video monitor JK-1MD Microphone Brightness control (0-10) Door release LED (red) DOOR RELEASE button Receive volume control (0-10) Chime tone volume (0-10) ZOOM/WIDE button POWER switch ADJUST button PAN/TILT button CALL button Option button (*) Speaker Transmit LED (red) TALK button OFF button MONITOR button (*) The option button controls connected option units such as turning lighting on and off and activation of added door releases. - 6 - Italiano Nederlands Español Fra
Résumé du contenu de la page N° 7
English Français Español Nederlands Italiano OPERATIONS 6 6-1 Answering a door call (HANDS-FREE mode, PTT mode) Press CALL button. 1 Instant voice call function 2 Even without answering, door area can be seen and heard with video and audio (for approx. 45 seconds). Inside sound is not heard outside. 2 Chime tone sounds, caller is seen on video monitor, and outside sound is heard. Audio and video turns off after approx. 45 seconds if not answered. PTT mode 3 Press and hold the TALK button
Résumé du contenu de la page N° 8
6-3 Entrance monitoring 1 Press MONITOR button in the standby mode. 3 Press OFF button to end communication. 2 The video monitor displays the image from the door station and the NOTES:1. T o talk to the entrance during entrance monitoring, momentarily incoming audio is heard. If you do not press TALK button, the press TALK button. This allows communication with the entrance. caller will not hear sounds from the inside station. 2. T he entrance monitoring turns off automatically after approx.
Résumé du contenu de la page N° 9
English Français Español Nederlands Italiano 6-6 Pan/Tilt operation 1 When a zoom picture is displayed, press the and buttons. : Up : Do wn : Left : Right Moving diagonally is also possible. [Zoom picture] T he image range of the zoom picture and wide picture differs. The edges of the wide picture do not display with the zoom picture. 6-7 Zoom Picture Preset The picture can be set to display using a set zoom picture position for 2 Press ZOOM/WIDE button (for seconds to mor
Résumé du contenu de la page N° 10
6-9 Backlight adjustment, Night sensitivity adjustment To perform adjustment To halt adjustment 1 Press ADJUST button when the screen is difficult to see. 1 Press ADJUST button during adjustment. Automatic adjustment to a more visible screen is performed. NOTES: 1. Distinguishing between day and night is automatically done by the door station. 2. Pressing ADJUST button at night makes the caller's face easier to see, but moving subjects may be more difficult to see. [Before a
Résumé du contenu de la page N° 11
English Warranty Aiphone warrants thats its products have no material or workmanship defects under normal use conditions for two years after delivery to the end user. Aiphone will perform repair or replacement free of charge if the product is defective and the warranty applies to the defect. Aiphone reserves unto itself the sole right to make the final decision whether there is a defect in materials and/or workmanship and whether or not the product is under warranty. This warranty shall not ap
Résumé du contenu de la page N° 12
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
