Instruction d'utilisation Panasonic TY-42PV30NZ

Résumé du contenu de la page N° 1

  +,-./ ,0
,*

 

 

 
!"#$%
##&#$''&(#"#(&()!(*

Résumé du contenu de la page N° 2

Unpack &IdentifyParts Left Location Pin Right LocationPin Left Glass Bracket Packer Top CablePin Right GlassBracket FrontRail Glassshelf Cable holder Back side Moulding Side Moulding Castor Front Moulding Base CARTONCONTENTS Quantity PartNumber Part Description Top M19721A1PO 1 Packer M19722A1PO 1 Base M19723A1PO 1 Front Rail M19591B2PO 2 FrontMouldings M19595A2PO 2 Back Side Mouldings M19592A1DF 2 Side Mouldings 2 M19619B1DF LeftGlass Bracket M19596A1PO 2 RightGlass Bracket M19597A1PO 2 Glass S

Résumé du contenu de la page N° 3

Résumé du contenu de la page N° 4

STEP 1 Castor x10 P860045 Base (underside) P800201x 16 1.Fasten5CastorstotheBaseasshown. 2.Insert Wooden Dowels asshownabove.

Résumé du contenu de la page N° 5

Allen key

Résumé du contenu de la page N° 6

Résumé du contenu de la page N° 7

Résumé du contenu de la page N° 8

STEP5 ThreadedRod P816172x 2 Allen key Threaded Rod Sleeve Nut P860256x 4 Allen key 1.Fit Sleeve Nutatone end of each Threaded Rod using anAllenKey. 2.Insert ThreadedRodintoAssembly through Base as shown. 3.Fit anotherSleeve Nut at other endofThreadedRod fromTop and tighten it turningboth AllenKeys inopposite direction of eachother.

Résumé du contenu de la page N° 9

STEP6 FrontRail Front Rail FrontRail Front Moulding 1.Fit 2SmallConnecting Rods to eachFrontRailas shown. 2.Fit Front Mouldings to Baseas shown. 3.Fit Front Rails on to Front Mouldings as shown.

Résumé du contenu de la page N° 10

STEP7 View from front of Stand FrontRail FrontRail Ensure thatFrontRail,FrontMouldingand Base areallflush on outsideedge. Front Moulding Front Moulding 1.Fasten the Front Rails andFrontMouldings to the Base while holdingthem flush with outsideedge ofStandusing2 Locking Screws.

Résumé du contenu de la page N° 11

STEP8 1.Tighten the4 pre-fitted Cams inTop, by turning themclockwise.

Résumé du contenu de la page N° 12

STEP9 P860246x 8 LeftGlass Bracketx2 Right GlassBracketx2 1.Fasten the Glass Brackets to Side Mouldings using Screws as shown.

Résumé du contenu de la page N° 13

STEP10 Thecurved part oftheGlass should beat the front. 1.Slideeach Glass Shelf into Glass Brackets and tighten GrubScrews fromthe undersideofbracketsas shown,make sure theBack Edge of Glass Shelf is flush withGlass Bracket.

Résumé du contenu de la page N° 14

Résumé du contenu de la page N° 15

Résumé du contenu de la page N° 16

Résumé du contenu de la page N° 17

STEP14 Ensure TV is standing straight onthe standbeforeyoutighten thebolts. 1.With help of an Assistant,lift theTelevision onto Pins ensuringthat thePins line up withthe Holes in baseofTelevision. 2.WhileGently pushingthe Plasma TV back to ensure theTVisstandingstraightonthe stand, tightentheTVwiththeBolts as shown below.

Résumé du contenu de la page N° 18

CABLE MANAGEMENT Once Cables are behind Pins, slide the Cable Pins across into the Side Moulding. Side Moulding Back Side Moulding 1.With Cable Pins pushed into Back Side Mouldings, place Cables behindpins,then slide Pins across into the Side Mouldings. Congratulations you have now finished theassembly for yourPanasonic TelevisionStand.