Instruction d'utilisation Ergotron StyleView 888-122

Résumé du contenu de la page N° 1

StyleView® Vertical Lift, PATIENT ROOM
User's Guide
WARNING: Because surfaces vary widely and the
ultimate mounting method is out of Ergotron’s control,
it is imperative that you consult with appropriate
engineering, architectural or construction professional
to ensure that your Ergotron mounting solution is
mounted properly to handle applied loads.
CAUTION: Do Not remove cardboard spacer until instructed to do so.
AB C D EFGH I J
1x 1x
1 1x
198.755 53.023
22.543
7.825 2.088
.888
1x
2
H
H
1

Résumé du contenu de la page N° 2

Centerline of Four-Hole Minimizing Vertical Lift Storage Profile VESA FDMI Pattern For keyboard to fit under the monitor when in storage position, follow these guidelines: 1. Keyboard should not be more than 8-1/8" (206 mm) deep if using wrist rest, or 9-1/2 ( mm) if no wrist rest is used. 2. Dimension “A” must be no greater than 6-5/8" (168 mm). NOTE: Keyboard needs to attach to the lowest set of holes as shown in Step 6. A Rear of Monitor 1 Ø 1/2" (12.8 mm) 2 ab c ½" (12.8mm) H" (H mm) NOTE:

Résumé du contenu de la page N° 3

4x 3 a 1 34 2 bc 4x 1/4-20 x 1-1/2" 5/32" 2 1 WARNING: Injury may result if the cardboard spacer is removed without fi rst lowering the keyboard bracket. DO NOT remove the cardboard spacer before lowering the keyboard bracket. 888-60-503-G-00 rev. B � 07/08 3/9

Résumé du contenu de la page N° 4

4x 4 8-32 x 1/4" 3/32" a 4x M4 x 10mm 4x b M4 x 10mm Recessed 4x 4x M4 x 20mm WARNING: The monitor will not be securely attached to the 9" Vertical Lift until the Locking Pin passes through the tab on the Quick Release Bracket. Do not leave the monitor unsupported until you are certain 5 the Locking Pin is in place. 1 34 2 888-60-503-G-00 rev. B � 07/08 4/9

Résumé du contenu de la page N° 5

2x 6 a b M4 x 10mm 20" - 22" (508 - 559 mm) recommended 2x 2.5mm c b d M4 x 10mm 2.5mm 7 a b c de fg h 888-60-503-G-00 rev. B � 07/08 5/9

Résumé du contenu de la page N° 6

Adjustments should move smoothly and easily through the full range of motion and stay where you set it. If adjustments are diffi cult and do not stay in the desired position, follow the instructions to loosen or tighten the tension to create a smooth, easy adjustment motion. Depending on your product and the adjustment, it may take several turns to notice a diff erence. 8 Follow these instructions to a tighten or loosen tension. 3/16" Follow these instructions to b tighten or loosen tension

Résumé du contenu de la page N° 7

2x 9 a bc M4 x 6mm 2x Cable Routing on Left10 Cable Routing on Right 2x 2x 3x 3x M4 x 6mm M4 x 6mm aabbcc Back View Back View Back View Back View dd 3x 3x M4 x 6mm M4 x 6mm 888-60-503-G-00 rev. B � 07/08 7/9

Résumé du contenu de la page N° 8

11 ab 4x M4 x 6mm 12 Route cables downward Route cables upward NOTE: NOTE: Leave enough slack in the cables for unrestricted movement. Leave enough slack in the cables for unrestricted movement. Back View Back View 888-60-503-G-00 rev. B � 07/08 8/9

Résumé du contenu de la page N° 9

888-60-503-G-00 rev. B � 07/08 9/9