Instruction d'utilisation Fisher-Price BOUNCE 'N PLAY ACTIVITY DOME 79534

Résumé du contenu de la page N° 1

Bounce ’n Play Activity Dome
Model Number: 79534
Instructions
Please save these instructions for future reference.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver.
Use only for a child who is unable to push up on hands and knees, pull up or sit unassisted.

Résumé du contenu de la page N° 2

WARNING • Never leave child unattended. ® • To prevent suffocation from entrapment, use only the Fisher-Price pad provided. Never use additional padding or mattress. • To prevent falls, use only for a child who is unable to push up on hands and knees, pull up or sit unassisted. • To prevent strangulation: _ Never place items with a string, such as hood strings or pacifier cords, around a child's neck. _ Never place this product near a window where cords from blinds or drapes can strangle a child

Résumé du contenu de la page N° 3

® ® Parts Metal Canopy Stay Pad 2 Covers 3 Toys 2 Base Wires Base Plastic Mesh Cover Stay 3 13 M5 x 1 /16" Screw - 2 M5 Lock Nut - 2 M6 x 1 /8" Screw - 8 M6 Lock Nut - 8 SHOWN ACTUAL SIZE 3

Résumé du contenu de la page N° 4

Assembly IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or ® sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price for replacement parts and instructions if needed. Never substitute parts. Button Hole Plastic Mesh 3 1 Frame Cover Stay Middle Hole Middle Hole Mesh Cover Frame Tube Frame Tube Base • Position the ends of the frame tubes against the middle holes in a frame. • Position the base upright on a fla

Résumé du contenu de la page N° 5

Assembly 5 7 Metal Canopy Stay Cover Upper Hole • Tighten the screws with a Phillips screwdriver. Do not Slot Tab over-tighten. • Repeat this procedure to attach the other ends of the frame tubes to the frame on the other side of the base. Frame 13 M5 x 1 /16" Screw - 2 M5 Lock Nut - 2 6 • Position one end of the metal canopy stay against the upper hole in a frame. Lower Hole 13 16 • Insert an M5 x 1 / " screw through the hole in the cover. Base Wire • Fit the end of the screw through the hole

Résumé du contenu de la page N° 6

® Assembly Use To Unfold Toys 8 Canopy Carry Straps Fasteners 1 Pad Fastener ® • Position the product on a flat surface. Base Fastener • Unfasten the carry straps. • Lift the canopy. • Fasten the pad fasteners to the base fasteners. • Attach the toys to the canopy fasteners. 2 Assembly is now complete, but Bounce ‘n Play Activity Dome is not ready for use. Please refer to the Use instructions, page 7, steps 3 and 4. Sides of Base Wire • Grasp both sides of a base wire. • Pull both sides of the b

Résumé du contenu de la page N° 7

® ® Use Using the Canopy 3 Canopy Down 5 Canopy Up Frame Groove Groove Base Wire • Lift the product up slightly so that the base wire “snaps” into the groove in each frame. Make sure you hear a “snap”. • Adjust the canopy up or down. • Repeat Use Steps 2 and 3 to unfold the other base wire. Using the Mesh Cover Zipper 4 Canopy Up Mesh 6 Cover Up Frame Groove Base Wire • Push down on the product to • Adjust the canopy and mesh cover up. be sure the base wires are in • While holding the mesh cove

Résumé du contenu de la page N° 8

Use Use To Fold for Portability Carry Straps 9 7 Frame Groove Groove Base Wire ® • Grasp both sides of a base wire. • Fasten the carry straps. • While lifting the product up slightly, pull both sides of the base wire outward to remove the base wire from the groove in each frame. Care Base Wire The pad is machine washable.Wash the pad separately 8 in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The fabric, frame and toys may be wiped c