Instruction d'utilisation Chief Manufacturing PNRIW

Résumé du contenu de la page N° 1

INSTALLATION INSTRUCTIONS
Instrucciones de instalación Istruzioni di installazione
Installationsanleitung Installatie-instructies
Instruções de Instalação Instructions d´installation
Large Flat Panel In-Wall Swing Arm Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PNRIW / PNRIWU

Résumé du contenu de la page N° 2

PNRIW / PNRIWU Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and CSAV, Inc., and its affiliated corporations and subsidiaries follow all instructions can result in serious personal injury, (collectively, "CSAV"), intend to make this manual accurate and damage to equipment, or voiding of factory warranty! It is the complete. However, CSAV makes no claim that the information installer’s responsibility to make sure all components are contained herei

Résumé du contenu de la page N° 3

Installation Instructions PNRIW / PNRIWU TOOLS REQUIRED FOR INSTALLATION AND PARTS (3/16") B (4) 2 short (SIDES) 2 long I/M A (1) x1 E (4) D (4) C (4) 5/16" 5/16" 5/16-18 x 5/8" F (16) G (4) H (1) J (1) 3/16" M(4) L (4) K (1) Figure 1 3

Résumé du contenu de la page N° 4

PNRIW / PNRIWU Installation Instructions Installation The following procedure assumes that a Chief Model PAC501 In-Wall accessory has previously been installed following the installation instructions provided with the PAC501. If a PAC501 is not installed or there are any other questions regarding the installation of this accessory, immediately contact a Chief Customer Service representative by calling 800-582-6480 or by visiting www.chiefmfg.com. WARNING: IMPROPER INSTALLATION CAN LEAD T

Résumé du contenu de la page N° 5

Installation Instructions PNRIW / PNRIWU NOTE: Holes are provided in the faceplate for use with a Display Installation padlock or similar locking device, if desired. In addition, the pin and nut may be removed from the upper holes WARNING: IMPROPER INSTALLATION CAN LEAD TO and moved to the lower holes for use as a more MOUNT FALLING CAUSING SEVERE PERSONAL INJURY permanent locking device. (See Figure 6) OR DAMAGE TO EQUIPMENT! DO NOT install display in a manner other than that specifi

Résumé du contenu de la page N° 6

PNRIW / PNRIWU Installation Instructions From Display 2 x 4 (A) x 1 3 1 4 3 2 From Display (M) x 4 Figure 7 Adjustments TENSION ADJUSTMENTS Pitch Tension Adjustment 1. With display mounted, check for desired Pitch tension. TM 2. If required, adjust the Centris Select knob right or left until desired Pitch tension is obtained. (See Figure 8) 3. To lock the mount at the desired position, tighten the Pitch locking screw. (See Figure 9) TM Centris Select Pitch Adjustment Knob 3 Pitch Locking Scr

Résumé du contenu de la page N° 7

Installation Instructions PNRIW / PNRIWU (L) x 1 1 (K) x 1 2 Socket Head Capscrew Figure 11 4. Using the adjustment wrench (L), turn adjustment bar (K) clockwise to increase swing arm tension or 1 counterclockwise to reduce swing arm tension. (Small adjustments of 1/8 turn or less are typically all that is required to achieve desired tension.) (See Figure 12) and (See Figure 13) 4 DECREASE Roll Adjustment Nut Figure 10 Swing Arm Tension Adjustment Swing arm tension is pre-set at the facto

Résumé du contenu de la page N° 8

PNRIW / PNRIWU Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 40 2668620 F +31 (0) 40 2668615 Asia Pacific A Room 30I, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112 8805-000242 ©2007 Chief Manufacturing www.chiefmfg.com P +86-755-8996 9226 ; 8996 9236 ; 8996 9220 10/07 F +86-755