Résumé du contenu de la page N° 1
INSTALLATION INSTRUCTIONS
FSD-4100
LCD Flat Screen
Swing-Down Mount
Perfect for home applications under kitchen cabinets or other
rooms with a soffit. The LCD Flat Screen Swing-Down mount is
a sturdy, versatile solution for LCD flat screen display or touch
screen control system mounting with 15” or smaller monitors.
The all steel mount provides smooth side-to-side pivot, 70º or
220º screen rotation and extends and retracts 2 3/4” to allow for
larger screen capacity. Hidden cable management permi
Résumé du contenu de la page N° 2
Installation Instructions FSD-4100 IMPORTANT WARNINGS AND PRECAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre- sponding instructions. WARNING:Improper installation can result in serious personal injury! Make sure that the mounting surface can sup- port a redundant weight factor five times the total wei
Résumé du contenu de la page N° 3
Installation Instructions FSD-4100 DIMENSIONAL DRAWING 2
Résumé du contenu de la page N° 4
Installation Instructions FSD-4100 INSPECT THE UNIT BEFORE INSTALLING WARNING: Watch for pinch points. Do not put your fingers between movable parts. 1. Carefully inspect the FSD-4100 for shipping damage. If any damage is apparent, call your carrier claims agent and do not continue with the installation until the carrier has reviewed the damage. NOTE: Read all instructions before starting installation. 2. Lay out components to ensure you have all the required parts before proceeding (see “DIME
Résumé du contenu de la page N° 5
Installation Instructions FSD-4100 PARTS Item Description Qty. Item Description Qty. 10 Mount 1 40 Screw, M4 X .7 X 20mm 4 10A Base Cover 1 50 Screw, M4 X .7 X 10mm 4 10B Cable Management Cover 1 60 Spacer, Nylon, .500 OD X .19 X .50 4 20 Nuts, T 3 70 Tie Wraps 4 30 Screws, 10-24 X 5/8” 3 80 Allen Wrench, 5/32” 1 10 10A 10B 20 30 40 70 50 60 80 4
Résumé du contenu de la page N° 6
Installation Instructions FSD-4100 FSD-4100 INSTALLATION WARNING: It is the responsibility of the installer to verify that the surface to which the FSD-4100 is anchored will safety support the combined load of all attached components and equipment. Install the FSD-4100 as follows: Base NOTE: Numbers in ( ) refer to parts in PARTS on page 4. Screws Cover 1. Remove two screws securing base cover (10A) and remove cover (see Figure 1). 2. Determine the exact mounting location prior to installation
Résumé du contenu de la page N° 7
Installation Instructions FSD-4100 ADJUSTMENTS Screen Height Adjustment 1. Using a screw driver, slightly loosen the screws (40 or 50) securing the display panel to the mounting bracket (see Figure 4). 2. Adjust the display panel to the desired height. Screws 3. Using a screw driver, tighten the screws securing the dis- Securing play panel to the mounting bracket. Monitor Arm Tension Adjustment CAUTION: Overtightening adjustment bolt will cause exces- sive wear and may distort adjustment compone
Résumé du contenu de la page N° 8
Installation Instructions FSD-4100 CABLE MANAGEMENT 1. Remove screw and cable management cover (10B) (see Figure 6). 2. Route the power/audio/video cables down the arm (see Figure 7). Cable Management 3. Route the power/audio/video cables through the slot in the bot- tom of the arm (see Figure 8). Cover 4. Secure the power/audio/video cables using tie wraps. 5. Proceed to “Right and Left 35 Degree Rotation” on page 8 or “Right and Left 110 Degree Rotation” on page 9, depending Figure 6. Cable Ma
Résumé du contenu de la page N° 9
Installation Instructions FSD-4100 Right and Left 35 Degree Rotation 1. Turn the base 35 degrees in one direction to its stop (see Figure 9). 2. Neatly and carefully, route the power/audio/video cables through the slot in the side of the base. 35 Degrees 3. Secure the power/audio/video cables using a tie wrap (70). 4. Trim excess from tie wrap. Stop 5. Install cable cover (10B) on arm and secure using screw (see Figure 10). 6. Install base cover (10A) on base and secure using two screws (see Fi
Résumé du contenu de la page N° 10
Installation Instructions FSD-4100 Right and Left 110 Degree Rotation 1. Using an Allen wrench (provided), remove the 35 degree stop (see Figure 11). 2. Turn the base 110 degrees in one direction to its stop (see Figure 12). 3. Neatly and carefully, wrap power/audio/video cables twice inside base with no slop or slack in cables (see Figure 13). 4. Route power/audio/video cables out access hole in base. 5. Secure cables to base using a tie wrap (70). 6. Trim excess from tie wrap. 7. Install cable
Résumé du contenu de la page N° 11
Installation Instructions FSD-4100 Check Rotation 1. Rotate screen in one direction until it reaches its stop (see Fig- ure 14). 2. If there is any binding or pinching, correct problem. 3. Rotate screen in the opposite direction until it reaches its stop (see Figure 15). 4. If there is any binding or pinching, correct problem. 5. If your cables do not allow you to reach the 110 degree limit, reinstall the 35 degree limitation screw. Figure 14. Rotate In One Direction Figure 15. Rotate In Opposit
