Instruction d'utilisation Axor High Spout 38030XX1

Résumé du contenu de la page N° 1

Installation Instructions / Warranty
2
Uno
38030XX1
02/2005 9.05406.01

Résumé du contenu de la page N° 2

2 Uno Single Control Lavatory Faucet 38030XX1 Technical Specification Maximum water pressure 145 psi Recommended water pressure 14.5 - 72 psi o Maximum hot water temp. 176 * o o Recommended hot water temp 120 - 140 * Max. flow rate @ 45 psi 2.2 gpm Max. deck thickness 1 5/8” Hole size in deck 1 3/8” o *Many municipalities require that the water heater be set no higher than 120 . Please know and follow all applicable plumbing codes when setting the temperature on the water heater. Installation c

Résumé du contenu de la page N° 3

Installation Instructions • Sit the faucet with black sealing ring in the faucet hole on top of the mounting surface. • From beneath, install the friction washer, metal washer, and mounting nut. Tighten the mounting nut, taking care not to overtighten. • Check the position of the faucet. When satisfied, use a slot-headed screwdriver to tighten the tensioning screws. • Feed the pull rod through the hole in the back of the faucet body. • Attach the supply lines to the supply stops with standard 3

Résumé du contenu de la page N° 4

Re-set the high temperature limit stop (optional) This step should be taken if the faucet is to be used by small children or others who should be protected from scalding. • Pull out the screw cover, located on the bottom of the handle. • Use a 3 mm allen wrench to loosen the set screw 2 complete turns. • Pull off the nut cover and the green high temperature limit stop ring. • Reinstall the high temperature limit stop ring so that the black positioning pin is in the notch corresponding to the des

Résumé du contenu de la page N° 5

Install the pop-up drain • Remove the plunger assembly. • Unscrew the drain outlet flange from the tee. • Unscrew the tailpiece from the tee. Wrap the threads with plumbers’ thread tape and replace. • Install the white, flexible sealing gasket to the flange. Sit it in the sink outlet. • From under the sink, install the black mack gasket, white friction ring , and retainer nut to the flange. Do not tighten the nut against the bottom of the sink at this time. • Thread the tee and tailpiece to t

Résumé du contenu de la page N° 6

User Instructions • Push the lever to the right to turn the water on. Push it backward to make the water warmer, forward to make the water cooler. o • The spout will swivel a full 360 . Service Parts 1 handle 38094XXX 2 nut cover 96763XXX 3 nut 97209000 4 cartridge 96764000 5 cartridge seal 95008000 6 aerator 96911XXX 7 mounting hardware 13961000 8 pull rod 96657000 6

Résumé du contenu de la page N° 7

Cleaning Recommendation for Hansgrohe Products Modern faucetry and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the Hansgrohe warranty. Cleaning Materials for Faucets and Showers • To remove lime scale, use only products made specifically for that purpose. Always follow the manufacturer’

Résumé du contenu de la page N° 8

THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no rinse” cleaning products, or the use of the product in any manner contrary to the product instructions. C. Labor or other expenses