Instruction d'utilisation American Standard Symphony 4508S

Résumé du contenu de la page N° 1

Installation
Instructions
SYMPHONY
4508
Spread Lavatory Faucet
with Speed Connect™ Drain 4508S
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only
on American Standard faucets.
Speed Connect Drain*
Certified to comply with ANSI A112.18.1
� 1/3 of the parts, installs in 1/3 of the time
M968672 Rev. 1.1
� No tools needed
� Never needs adjustment
� Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is

Résumé du contenu de la page N° 2

INSTALL POP-UP DRAIN 2 Fig. A. Fig. B. REAR OF SINK Remove CLEAR PLASTIC COVER (1). Remove 1 CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A. 4 3 Drop DRAIN BODY (4) through sink drain 6 hole. Make sure WHITE FOAM GASKET (5) 5 is under flange of DRAIN BODY (4). Fig. B. SINK Note: No plumber’s putty or caulk is required. 2 DRAIN HOLE The CABLE ATTACHMENT POINT (6) must face towards the rear of the SINK. Fig. B. INSTALL BLACK GASKET 3 Install BLACK CONE GASKET (1) onto DRAIN BODY (2) fro

Résumé du contenu de la page N° 3

ATTACH CABLE CONNECTOR 6 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 1-1/4” O.D. 2 CHECK OPERATION OF POP-UP 7 1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 2 MAKE WATER SUP

Résumé du contenu de la page N° 4

INSTALL HANDLES 9 Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without a spline is facing up. Fig. A. Tighten THREAD ON STEM SCREW (3) to secure ADAPTER (1). TO DECK 4 ADAPTER Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting TOP male teeth on ADAPTER (1) to female teeth in HANDLE (4). Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5) 1 until snug against mounting surface. Fig. A. 3 2 SPLINE END DOWN 5 TEST INSTALLED FITTING 10 5 With HANDLES (1) in

Résumé du contenu de la page N° 5

Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. C

Résumé du contenu de la page N° 6

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate LOGO Stopper s

Résumé du contenu de la page N° 7

TIPS FOR REMOVING YOUR OLD DRAIN: Most existing drains can be removed quickly and easily with only a pair of channel- lock pliers or a wrench. However, there may be situations where it is difficult to remove your old drain or determine how the drain is disassembled. Depending upon the existing Drain in your sink, it is either removed from above or below the sink. The illustrations below show some typical drain installations and how they are disassembled from the sink. The following tips can h