Résumé du contenu de la page N° 1
Cordless Impact
Driver
Equipped with Electric Brake
MODEL 6990D
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Résumé du contenu de la page N° 2
SPECIFICATIONS Model 6990D Machine screw 4 mm - 8 mm (5/32” - 5/16”) Capacities Standard bolt 5 mm - 12 mm (3/16” - 1/2”) High tensile bolt 5 mm - 10 mm (3/16” - 3/8”) No load speed (RPM) 0 - 2,300/min. Impacts per minute 0 - 3,000 Overall length 168 mm (6-5/8”) Net weight 1.4 kg (3.1 lbs) Battery Charger DC1414 Input A. C. only 50 Hz - 60 Hz Output D. C. 7.2 V - 14.4 V Battery Cartridge 9122 9134 9135 Voltage 9.6 V Charging time 45 min. 60 min. 70 min. • Manufacturer reserves the right to chang
Résumé du contenu de la page N° 3
9. Remove adjusting keys or wrenches Work Area before turning the tool on. A wrench or a 1. Keep your work area clean and well lit. key that is left attached to a rotating part of Cluttered benches and dark areas invite acci- the tool may result in personal injury. dents. 10. Do not overreach. Keep proper footing 2. Do not operate power tools in explosive and balance at all times. Proper footing and atmospheres, such as in the presence of balance enable better control of the tool in flammable li
Résumé du contenu de la page N° 4
18. Maintain tools with care. Keep cutting one tool may create a risk of injury when tools sharp and clean. Properly maintained used on another tool. tools with sharp cutting edge are less likely to SERVICE bind and are easier to control. 21. Tool service must be performed only by 19. Check for misalignment or binding of qualified repair personnel. Service or main- moving parts, breakage of parts, and any tenance performed by unqualified personnel other condition that may affect the tool’s may r
Résumé du contenu de la page N° 5
SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts .../min................revolutions or reciprocation per minute ................... direct current ................number of blow ................... no load speed n ˚ IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE USC001-3 1. SAVE THESE INSTRUCTIONS - This man- 6. To reduce risk of damage to electric plug ual contains important safety and operat- and cord, pull by plug rather than cor
Résumé du contenu de la page N° 6
11. Do not disassemble charger or battery 14. Young children should be supervised to cartridge; take it to a qualified serviceman ensure that they do not play with the bat- when service or repair is required, Incor- tery charger. rect reassembly may result in a risk of 15. If operating time has become excessively electric shock or fire. shorter, stop operating immediately. It 12. To reduce risk of electric shock, unplug may result in a risk of overheating, possi- charger from outlet before attem
Résumé du contenu de la page N° 7
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 002810 Installing or removing battery cartridge 1 • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. 2 • To insert the battery cartridge, align the tongue on the battery cartridge
Résumé du contenu de la page N° 8
NOTE: • The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. • When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. • If you charge a battery cartridge fro
Résumé du contenu de la page N° 9
002793 Switch action CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates 1 properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger. Tool speed is 1. Switch trigger increased by increasing pressure on the switch trigger. Release the switch trigger to stop. Electric brake This tool is equipped with an electric brake. If the tool consis- tently fails to quickly stop after switch tri
Résumé du contenu de la page N° 10
001266 Installing or removing driver bit or socket bit Use only the driver bit or socket bit shown in the figure. Do 12 mm 9 mm not use any other driver bit or socket bit. (15/32”) (3/8”) 001267 To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly. 1 2 NOTE: • If the bit is not inserted deep e
Résumé du contenu de la page N° 11
OPERATION 002840 The proper fastening torque may differ depending upon the Standard bolt kind or size of the screw/bolt, the material of the workpiece to be fastened, etc. The relation between fastening torque and fastening time is shown in the figures. N.m (ft.lbs) Hold the tool firmly and place the point of the driver bit in the 80 (58) M12(1/2”) screw head. Apply forward pressure to the tool to the extent 60 (43) that the bit will not slip off the screw and turn the tool on to M10(3/8”) 40 M1
Résumé du contenu de la page N° 12
4. The manner of holding the tool or the material of driving position to be fastened will affect the torque. 5. Operating the tool at low speed will cause a reduction in the fastening torque. MAINTENANCE CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. 001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brush
Résumé du contenu de la page N° 13
EN0001-1 Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. Ni-Cd 2. a) Take the battery to your nearest Makita Factory Ser- vice Center or b) Take the battery to your nearest Makita Authorized Service Center or Distributor that has been desig- nated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine
Résumé du contenu de la page N° 14
Memo 14
Résumé du contenu de la page N° 15
Memo 15
Résumé du contenu de la page N° 16
Memo 16
Résumé du contenu de la page N° 17
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 17 Cut
Résumé du contenu de la page N° 18
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Résumé du contenu de la page N° 19
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO LOUISIANA NEW YORK PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 5626 Jefferson Hwy. 4917 Genessee Street 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Harahan, LA 70123 Cheektowaga, NY 14225 Hato Rey, PR 00917 (205) 620-1791 (303) 371-2850 (504) 733-4138 (716) 685-9503 (787) 250-8776 131-35 31st Ave. ARIZONA FLORIDA MARYLAND Flushing, NY 11354 TENNESSEE 3707 E. Broadway Rd., Ste. 6 62
Résumé du contenu de la page N° 20
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
