Résumé du contenu de la page N° 1
Shear Wrench
MODEL 6920NB
MODEL 6922NB
INSTRUCTION MANUAL
DOUBLE
lNSULATlON
Dimensions Net
Model Bolt size Max. torque No load speed
(L x W x H)
IRPMI weight
6920NB 5/8". 314" 60 kg.m
241 mm x 84 mm x 246 mm 4.3 kg
26
(A4901 (434 Ibs,ftl (9-112'' x 3-5/16" x 9-11/16") (9.5 lbsl
6922N8 5/13", 34". 7/8" 82 kg,m mm x 84 mm x 252 mm
249 4.8 kg
18
(A4901 1593 Ibs,ft) 19-13/16" x 3-5/16" x 9-15/16") (10.6 Ibsl
Résumé du contenu de la page N° 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence of f
Résumé du contenu de la page N° 3
0-25 1 26 - 60 51 - 100 101 - 150 Ampere Rating More Not More AWG Then Then ~ 18 16 16 14 0- 6 6- 10 10 - 12 16 12 - 16 14 Not Recommended 17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 18. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully check
Résumé du contenu de la page N° 4
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the , nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. ADDITIONAL SAFETY RULES 1. Always be sure
Résumé du contenu de la page N° 5
Removing or installing the outer and inner sleeves CAUTION : *Always be sure that the tool is switched off and unplugged before removing or installing the outer and inner sleeves. Be careful not to allow foreign matter to enter the insides of the tool when removing or installing the outer and inner sleeves. The outer sleeve M20 and inner sleeve 3/4" are factory-installed. If you need other sizes for your work, replace the sleeves as follows. Loosen the two screws while holding the outer
Résumé du contenu de la page N° 6
Insert the outer and inner sleeves into the tool while rotating the inner sleeve alternately clockwise and counterclockwise until there is no gap between the outer sleeve and the tool. See the figure below. Then tighten the two screws securely. Switch action To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates proper- ly and returns to the “OFF” position when released. Bolt ins
Résumé du contenu de la page N° 7
When the specified torque is attained, the Il ' bolt tip will be sheared at its notched por- tion. The bolt tip will remain inside the tion inner sleeve. - - Release the trigger and withdraw the tool in a straight line. __Outer sleeve Press the tip ejector (tip lever) to eject the bolt tip from the tool. Catch the sheared bolt tips to prevent them from falling dangerously below. Keep the tips off of the ground, floor, walkways, etc. to prevent injury from tripping or falling. Bolt t
Résumé du contenu de la page N° 8
.. .. .. .... MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. - Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Open the protector. Use a screwdriver to remove the brush
Résumé du contenu de la page N° 9
Fob - 10-'94 US SHEAR WRENCH Model 6920NB Model 6922NB Note: The switch, noise suppressor and other part configuratlons may differ from country 10 country 9
Résumé du contenu de la page N° 10
.. MODEL 6920N8. 6922118 F.b-10--'84 US ILLM ,& DESCRIPTION $.& DESCRlPTlDN "rE MA I I 38 1 2 1 39 I 3 I 4 I 5 I 40 4 6 I 41 I 42 I 43 I 7 I 44 I 8 1 45 I 9 I 46 I 41 I 48 I 49 IO 1 I I1 4 50 I 51 I I2 4 52 I 53 I 54 2 13 4 55 1 56 I 51 4 14 I 58 4 15 4 59 I 60 I 61 1 16 2 62 I 17 4 63 I I0 4 G4 1 19 4 65 I 66 20 4 I 21 1 61 I 22 4 I 23 I 68 I 24 4 69 I 25 26 I 10 I 21 I 11 1 12 2 13 2 28 I 14 1 29 I 76 2 30 I 11 I 31 I 70 1 32 I 79 1 33
Résumé du contenu de la page N° 11
Résumé du contenu de la page N° 12
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of Califomia] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: 0 Lead from lead-based paints, 0 Crystalline silica from bricks and cement and other masonry products, and Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this t
