Instruction d'utilisation Harbor Freight Tools PROFASSIONAL 47214

Résumé du contenu de la page N° 1

®
3/8” AIR RATCHET
WRENCH
Model 47214
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright 2002 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353

Résumé du contenu de la page N° 2

Specifications Drive Size 3/8” Air Consumption SCFM @ 90 PSI = 6 Torque (Foot Pounds) CW - 48, CCW - 50 Air Inlet 1/4” - 18 NPT Female Recommended Air Pressure 90 PSI Drive Hardness 38 - 55 HRC RPM’s 130 @ 90 PSI Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front c

Résumé du contenu de la page N° 3

8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. 9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Disconnect a

Résumé du contenu de la page N° 4

Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be under- stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the parts listed on page 6 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of

Résumé du contenu de la page N° 5

Operation (continued) Note: Turn off your air compressor and disconnect the air hose when you are changing sockets. After you attach the socket, attach the air hose and turn the air compressor on. 5. Select the appropriate size 3/8” socket for your needs. 6. Attach the socket (not included) to the Anvil (#32). 7. Gently squeeze the Throttle Lever (#9) and determine which direction the drive turns. Clockwise direction will tighten, and counterclockwise will loosen. 8. If the drive isn’t tur

Résumé du contenu de la page N° 6

Parts List Part No. Description Part No. Description 1 Housing 22 Idler Gear Plate 2 Valve Plug 23 Idler Gear Pin 3 0-ring 24 Clamp Nut 4 Spring 25 Spacer 5 Roll Pin 26 Rachet Housing 6 0-ring 27 Pin 7 Spring Pin 28 Needle Bearing 8 Throttle Valve 29 Crank Shaft 9 Throttle Lever 30 Drive Bushing 10 End Plate Cap 31 Rachet Yoke 11 Rear Bearing 32 Anvil 12 Rear Plate 33 Spring 13 Rotor Blade 34 Washer 14 Rotor 35 Thrust Washer 15 Cylinder Pin 36 Retainer Ring 16 Cylinder 37 Rachet Pawl 17 Front Pl

Résumé du contenu de la page N° 7

Assembly Drawing 24 34 40 25 39 32 38 26 33 2 3 42 4 14 27 5 28 37 15 35 6 29 16 8 36 17 30 13 18 41 31 19 20 1 21 22 7 23 10 11 9 12 Page 7 SKU 47214