Instruction d'utilisation Harbor Freight Tools 93296

Résumé du contenu de la page N° 1

3/8” IMPACT WRENCH
Model 93296
ASSEMBLY AND OPERATING
INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced

Résumé du contenu de la page N° 2

Specifications Maximum Torque 75 Ft. Lbs. Drive Size 3/8” Air Inlet 1/4” - 18 NPT Recommended Air Pressure 90 PSI Free Speed 10,000 RPM Air Consumption 3 CFM Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Sa

Résumé du contenu de la page N° 3

9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Disconnect air hose when not in use. 11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the t

Résumé du contenu de la page N° 4

Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the parts listed on page 7 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of t

Résumé du contenu de la page N° 5

Operation (continued) Refer to the illustration on page 6, and the Assembly Drawing on page 8. Note: Turn off your air compressor and disconnect the air hose when you are changing sockets. After you attach the socket, attach the air hose and turn the air compressor on. 4. Select the appropriate size 3/8” drive socket for your needs. 5. Push and snap the socket (not included) onto the Anvil (6). 6. Turn the Air Regulator (32) in the direction indicated by the H arrow on the Regulator to increase

Résumé du contenu de la page N° 6

Maintenance 1. Make sure your Impact Wrench is disconnected from the air hose before attempting any maintenance. 2. Wipe the Impact Wrench down with a lint free cloth after each use. 3. Make sure the Anvil (6) is clear of dirt or debris. If possible, spray it with compressed air before each use. 4. Periodically, add a high quality machine oil to the oil inlet by removing the Oil Screw (39). See illustration, below. 5. If you do not use an inline oiler/filter system, lubricate the tool daily

Résumé du contenu de la page N° 7

Parts List Pn artDy escriptio Qt 'tPn arDy escriptio Q't 1rM1 oto 2r3C4 ap Washe 2lO1 il Sea 2w4S1 cre 3g"1 O" Rin 2n5V1 alve Pi 4rS1 ocket Retaine 2g6"1 O" Rin 5hS1 pindle Bus 2l7S1 teel Bal 6kA1 nvil Shan 2g8S1 prin 7mD1 river Ca 2t9I1 nle 8gH1 ammer Do 3g0S1 prin 9eH1 ammer Cag 3g1"1 O" Rin 1n 0H1 ammer Pi 3r2A1 ir Regulato 1e 1F1 ront End Plat 3n3P1 i 1l 2O1 il Sea 3r4T1 rigge 1g 3B1 all Bearin 3n5P1 i 1r 4R1 oto 3r6R1 everse Leve 1e 5R6 otor Blad 3g7"2 O" Rin 1r 6C1 ylinde 3e8R1 everse Valv

Résumé du contenu de la page N° 8

Assembly Drawing SKU 93296 For technical questions, please call 1-800-444-3353 Page 8