Résumé du contenu de la page N° 1
14.4 VOLT IMPACT DRIVER KIT
1/4” HEX DRIVE
Model 92472
OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
®
©
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For tec
Résumé du contenu de la page N° 2
PRODUCT SPECIFICATIONS Item Description Electrical Power Output Source: 14.4 VDC Battery ® Requirements Battery Type: 1.3 Ah Panasonic Power Input Source: 120 VAC/60 Hz Charger Charge Time: 1 Hour Quick Charge Charger Power Plug: 2 Prong, Polarized Drive Size/Type 1/4” Quick Change Hex Drive Impact Type Pin Clutch Trigger Type Variable Speed: 0-2300 RPM/IPM; Reversible w/Trigger Lock Maximum Torque 850 In./Lbs Accessories Carrying Case / Charger / Battery 1/4” Socket / 5/16” Soc
Résumé du contenu de la page N° 3
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 1. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 2. Do not expose power tools to rain or wet conditions. Water entering a power
Résumé du contenu de la page N° 4
TOOL USE AND CARE 1. Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 2. Do not use the power tool if the Trigger (34) does not turn it on or off. Any tool that cannot be controlled with the Trigger is dangerous and must be replaced. 3. Disconnect the power tool from its Battery (40) before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures
Résumé du contenu de la page N° 5
obstructions, grease, oil, trash, and other debris. Do not use the Impact Driver in areas near flammable chemicals, dusts, and vapors. Do not use this product in a damp or wet location. 2. Maintain labels and nameplates on this product. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 3. When using the Impact Driver, always maintain a firm grip on the tool with both hands. 4. Hold the tool by its insulated gripping surfaces when perf
Résumé du contenu de la page N° 6
13.Always switch to a fresh Battery (40) when tool performance begins to diminish. Severe heat is most destructive to a Battery. The more heat generated, the faster the Battery loses power. A Battery that gets too hot can be permanently damaged. Never over-discharge a Battery by using the tool while tool performance is decreasing. Never attempt to discharge a tool’s Battery by continuing to pull the tool Trigger (34). When tool performance begins to diminish, stop the tool, recharge the Bat
Résumé du contenu de la page N° 7
in its “OFF” position, the Battery (40) is removed from the Impact Driver, and the Charger (46) is unplugged from its electrical outlet prior to making any adjustments to the tool. (See Figure A.) LOCK SLEEVE (9) TRIGGER LOCK FORWARD/REVERSE LEVER (37) TRIGGER (34) CHARGER (46) BATTERY (40) FIGURE A 2. Lock Sleeve (9): Accepts the 1/4” shank diameter Double End Screwdriver (39), 1/4” Socket (42), 5/16” Socket (43), 3/8” Socket (44), and 15/32” Socket (45). To install the Screwdriver or Sockets
Résumé du contenu de la page N° 8
operate at full power. Do not recharge the Battery longer than 1-1/2 hours, as damage to the Battery and/or Charger (46) will occur. (See Figure A.) 3. Make sure the Trigger (34) on the Impact Driver is in its “OFF” position. Slide the Battery (40) off the Handle of the Impact Driver. Next, insert the Battery onto the Charging Socket of the Charger (46). Then, plug the Charger into the nearest 120 volt, grounded, electrical outlet. Do not leave unattended while charging. (See Figure A.) 4
Résumé du contenu de la page N° 9
2. If necessary, adjust the Forward/Reverse Lever (37). (See Figure A.) 3. Whenever possible, secure the workpiece in place, using a vise or clamps (not included). 4. Insert the fully charged Battery (40) into the Handle of the Impact Driver. (See Figure B.) 5. Make sure to hold the Impact Driver firmly with both hands, as torque from the Motor will cause the tool to twist. 6. Insert the Screwdriver (39) into the screw, or insert the Socket (42, 43, 44, 45) onto a bolt. Then, turn on the Impact
Résumé du contenu de la page N° 10
5. When storing: Always remove the Battery (40) from the Impact Driver. Keep the Impact Driver and its accessories in a clean, dry location and out of children’s reach. 6. CAUTION! All maintenance, service, or repairs not listed in this manual are only to be attempted by a qualified service technician. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTUR
Résumé du contenu de la page N° 11
ASSEMBLY DIAGRAM SKU 92472 For technical questions, please call 1-800-444-3353 PAGE 11 42: 1/4” Socket not shown. 43: 5/16” Socket not shown. 44: 3/8” Socket not shown. 45: 15/32” Socket not shown. 46: Charger not shown. 47: Carrying Case not shown. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
