Résumé du contenu de la page N° 1
Nuscan 3000
Laser Barcode
Scanner
Programming Manual
Résumé du contenu de la page N° 2
FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause harmful interference to radio commu
Résumé du contenu de la page N° 3
Table of Contents 1. INTRODUCTION………………………………………………………………………………..………2 2. INSTALLATION………………………………………………………………………………..….......4 USB Connection…………………………………………………………………………………5 PS2(K/B) Connection………………………………………………………………………….5 RS232 Connection………………………………………………………………………………6 3. SET UP FROM BAR CODE LABEL…………………………………………………………..……..7 Multi-interface Functions…………………………………………………………………….8 Interface-KBW………………………………………………………………………………….10 Interface-Serial…………………………………………………………………………………11
Résumé du contenu de la page N° 4
Introduction 2
Résumé du contenu de la page N° 5
Laser barcode scanner combines the best scanning performance and value. The device provides an accurate, easy, and fast method of data entry and data storage for computerized information systems. It is easy to install and does not require software or drivers to operate. The products we are offering can be integrated into a computer system by RS232, PS2 or USB interface. All the operating parameters are programmed by bar code programming menu and stored in non-volatile RAM which can
Résumé du contenu de la page N° 6
Installation 4
Résumé du contenu de la page N° 7
Insert the plug on the free end of the Communications Cable into the appropriate connector on the host as below described: 1. USB Connection connect with host 2. PS2(K/B) Connection connect with host connect with keyboard’s connector 5
Résumé du contenu de la page N° 8
3. RS232 Connection connect with host require adapter for power supply NOTE: for Serial port (RS232 cable), please plug the power connector of 5V power adapter to RS232 cable. 1. Be sure that Host computer is turned on. 2. Ensure that all connections are secure. 3. Turn on your host. And please operate the scanner under the right software application. 4. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default), and press the trigger. 5. On successful
Résumé du contenu de la page N° 9
Setup from Bar Code Label 7
Résumé du contenu de la page N° 10
Multi-Interface Functions – 1 OUTPUT FIRMWARE VERSION RESET CONFIGURATION TO DEFAULTS 0A 0B OUTPUT OUTPUT MODE – KEYBOARD WEDGE OUTPUT MODE - SERIAL MODE 000600 000601 BUZZER / GOOD READ BEEP TONE – NONE GOOD READ BEEP TONE - RESET LED 014200 0B142 IMAGE DECODE OPTIONS REVERSE IMAGE – DECODE OPTIONS REVERSE IMANGE ENABLE - DISABLE 01391 01390 CODE ID DECODE OPTIONS SEND BAR CODE ID - DECODE OPTIONS SEND BAR CODE DISABLE ID – AS A PREF
Résumé du contenu de la page N° 11
Multi-Interface Functions – 2 READING SCAN MODE – SINGLE SCAN SCAN MODE – SINGLE SCAN NO MODE TRIGGER 013300 013301 SCAN MODE – MULTISCAN SCAN MODE – MULTISCAN NO TRIGGER 013302 013303 SCAN MODE – CONTINUOUS SCAN SCAN MODE - PULSE 013304 013305 LASER/CCD TIMEOUT – 5 SECONDS LASER/CCD TIMEOUT – 2 SECONDS 0134005 0134002 LASER/CCD PULSE RATE - 7 LASER/CCD PULSE RATE - 3 013507 013503 9
Résumé du contenu de la page N° 12
Interface – KBW PC Communication WEDGE MODE - AUTODETECT WEDGE MODE – SCAN SET 2 PASS THRU 000200 000204 TRANSMIT TRANSMIT SPEED - 0 TRANSMIT SPEED - 25 SPEED 0000000 0000025 LANGUAGE KEYBOARD COUNTRY - USA KEYBOARD COUNTRY - GERMAN 0005000 0005010 KEYBOARD COUNTRY – FRANCE KEYBOARD COUNTRY - UNIVERSAL 0005009 0005025 10
Résumé du contenu de la page N° 13
Interface – Serial - 1 BAUD RATE SERIAL BAUD RATE - 2400 SERIAL BAUD RATE - 4800 000703 000704 SERIAL BAUD RATE - 9600 SERIAL BAUD RATE - 19200 000705 000706 HAND SHAKE SERIAL HANDSHAKE – XON/XOFF SERIAL HANDSHAKE - NONE 001200 001201 SERIAL HANDSHAKE – RTS/CTS SERIAL HANDSHAKE – ACK/NAK 001202 001203 SERIAL HANDSHAKE TIMEOUT – SERIAL HANDSHAKE TIMEOUT – 2 SECONDS 5 SECONDS 0013020 0013050 11
Résumé du contenu de la page N° 14
Interface – Serial - 2 PARAMETERS SERIAL DATA BITS - 8 SERIAL DATA BITS - 7 00081 00080 SERIAL STOP BITS - 1 SERIAL STOP BITS - 2 00090 00091 SERIAL PARITY - NONE SERIAL PARITY - ODD 001000 001001 SERIAL PARITY - EVEN SERIAL PARITY - MARK 001002 001003 SERIAL PARITY - SPACE SERIAL PARITY - RESET 001004 0B010 12
Résumé du contenu de la page N° 15
Symbologies On/Off - 1 CODE 11 CODE 11 - ENABLE CODE 11 - DISABLE 01261 01260 CODE 39 CODE 39 ENABLE CODE 39 DISABLE 00221 00220 FULL ASCII ENABLE FULL ASCII DISABLE 00231 00230 13
Résumé du contenu de la page N° 16
Symbologies On/Off - 2 CODE 93 CODE 93 - ENABLE CODE 93 - DISABLE 00621 00620 CODE 128 CODE 128 - DISABLE CODE 128 - ENABLE 00691 00690 CODE 128 ISBT - ENABLE CODE 128 ISBT - DISABLE 00701 00700 CODABAR CODABAR - ENABLE CODABAR - DISABLE 00851 00850 INTERLEAVED 2 OF 5 I2OF5 - ENABLE I2OF5 - DISABLE 00961 00960 INDUSTRIAL 2 OF 5 ID2OF5 - ENABLE ID2OF5 - DISABLE 01061 01060 14
Résumé du contenu de la page N° 17
Symbologies On/Off - 3 MSI MSI - ENABLE MSI - DISABLE 01151 01150 UPC/EAN UPC-A DISABLE UPC-A ENABLE 00341 00340 UPC-E ENABLE UPC-E DISABLE 00351 00350 EAN-13 ENABLE EAN-13 DISABLE 00361 00360 EAN-8 ENABLE EAN-8 DISABLE 00371 00370 15
Résumé du contenu de la page N° 18
Symbologies Set Up - 1 CODE 11 CODE 11 ID CHARACTER – “m” CODE 11 ID CHARACTER – “Z” 0131m 0131Z CODE 11 LASER/CCD REDUNDANCY - CODE 11 LASER/CCD REDUNDANCY - ENABLE DISABLE 01321 01320 CODE 39 CODE 39 SS CHAR - NONE CODE 39 SS CHAR ‛+’ 002700 002704 CODE 39 SEND START/STOP CHARS CODE 39 SEND START/STOP CHARS ENABLE DISABLE 00281 00280 CODE 39 ID CHARACTER ‛a’ CODE 39 ID CHARACTER ‛z’ 0031a 0031Z CODE 39 LASER/CCD RED
Résumé du contenu de la page N° 19
Symbologies Set Up – 2 CODE 93 CODE 93 ID CHARACTER – “h” CODE 93 ID CHARACTER – “Z” 0066h 0066Z CODE 93 LASER/CCD REDUNDANCY - CODE 93 LASER/CCD REDUNDANCY - ENABLE DISABLE 00681 00680 CODE 128 CODE 128 ID CHARACTER – ‛g’ CODE128 ID CHARACTER - ‛Z’ 0081g 0081Z CODE 128 LASER/CCD REDUNDANCY - CODE 128 LASER/CCD REDUNDANCY - ENABLE DISABLE 00841 00840 CODABAR CODABAR SEND START/STOP CHARS - CODABAR SEND START/STOP CHARS - ENABLE DISABLE
Résumé du contenu de la page N° 20
Symbologies Set Up – 3 CODABAR CODABAR ID CHARACTER – ‛k’ CODABAR ID CHARACTER – ‛Z’ 0094k 0094Z CODABAR LASER/CCD REDUNDANCY CODABAR LASER/CCD - ENABLE REDUNDANCY - DISABLE 00951 00950 Interleaved 2 of 5 I2OF5 ID CHARACTER – ‛i’ I2OF5 ID CHARACTER – ‛Z’ 0104i 0104Z I2OF5 LASER/CCD REDUNDANCY - I2OF5 LASER/CCD REDUNDANCY - ENABLE DISABLE 01051 01050 Industrial 2 of 5 ID2OF5 ID CHARACTER - ‛j’ ID2OF5 ID CHARACTER - ‛Z’ 0113j 011
