Résumé du contenu de la page N° 1
Operating Manual
®
Mark Levinson
Nº26
Dual Monaural
Preamplifier
Madrigal Audio Laboratories, Inc.
17
Résumé du contenu de la page N° 2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffic
Résumé du contenu de la page N° 3
Important safety instructions Please read all instructions and precautions carefully and completely before operating your Nº26 Dual Monaural Preamplifier. 1. ALWAYS disconnect your entire system from the AC mains before connecting or disconnecting any cables, or when cleaning any component. 2. This product is equipped with a three-conductor AC mains power cord which includes an earth ground connection. To prevent shock hazard, all three connections must ALWAYS be used. If your electrical outlets
Résumé du contenu de la page N° 4
® From all of us at Madrigal Audio Laboratories, thank you for choosing the Mark Levinson Nº 26 Dual Monaural Preamplifier. A great deal of effort went into the design and construction of this precision device. Used properly, it will give you many years of enjoyment. 20
Résumé du contenu de la page N° 5
Table of contents Front panel ...................................................................................................1 Rear panel ...................................................................................................3 Unpacking and placement .......................................................................5 Unpacking .............................................................................................. 5 Placement ...........................................
Résumé du contenu de la page N° 6
22
Résumé du contenu de la page N° 7
0° 180° STEREO MONO AUX 1 5 PHONO/ MADRIGAL AUDIO LABORATORIES AUX 2 4 6 TUNER TAPE 1 0dB 0dB INPUT TAPE 2 3 7 +1 +1 -1 -1 TAPE 1 CD DEFEAT MONITOR TAPE 2 DUAL MONAURAL 8 -2 +2 -2 +2 2 PREAMPLIFIER Nº 26 1 9 -3 +3 -3 +3 OFF 10 -4 +4 -4 +4 INPUT OUTPUT -5 +5 -5 +5 RECORD SELECTOR MONITOR SELECTOR SELECTOR LEVEL BALANCE 1 BALANCE 2 2 7 1 3 4 5 6 6 Front panel 1 RECORD SELECTOR Selects between the program source (selected via the INPUT SELECTOR), and either of two tape monitor inputs (selected via
Résumé du contenu de la page N° 8
5 OUTPUT LEVEL Adjusts volume at the main outputs. The OUTPUT LEVEL control doesn't affect the tape outputs. Note: In some systems, particularly those with high-efficiency loudspeakers, high-gain amplifiers, and balanced interconnections, it's possible that you may hear some low- level sound through your loudspeakers even with the Nº26's OUTPUT LEVEL control set to OFF. If this occurs with all inputs, reduce the line gain (via the internal switches). If this occurs only when listening to the sou
Résumé du contenu de la page N° 9
2 4 4 10 BALANCED OUTPUT OPTIONAL BALANCED INPUT RL POWER MAIN OUT TAPE 2 OUT TAPE 1 OUT DUAL MONAURAL DESIGNED AND MANUFACTURED RL AUX 2 SUPPLY IN U.S.A. BY PREAMPLIFIER MADRIGAL INPUT AUDIO LABORATORIES INC. Nº 26 PUSH PUSH S/N: RL RLRL CD AUX 1 PHONO/AUX 2 TUNER TAPE 2 IN TAPE 1 IN RL RL RL 1 3 5 5 6 7 8 9 11 Rear panel PRECAUTION Disconnect all associated equipment from the AC mains BEFORE making any signal connections and applying power to the Nº26/PLS- 226. 1 BALANCED OUTPUT If your power
Résumé du contenu de la page N° 10
4 TAPE 1 OUT, TAPE 2 OUT Connect these outputs to the right-channel and left-channel tape inputs of your tape machine. 5 TAPE 1 IN, TAPE 2 IN Accept right-channel and left-channel signal leads from the tape- output connectors of a tape machine. These inputs can also be used with other line-level source equipment. These outputs are unaffected by the OUTPUT LEVEL control on the front panel of the Nº26. 6 POWER SUPPLY INPUT Accepts one end of the DC cable that connects the Nº26 to the PLS-226. 7CD
Résumé du contenu de la page N° 11
Unpacking and placement Unpacking Unpack your Nº26 Preamplifier and PLS-226 Power Supply, and keep all packing materials for future transport. Remove all accessories from the cartons. Carefully inspect the product for damage and flaws. If you find any, see your Mark Levinson dealer immediately. Placement Place the Nº26 as close as possible to the source equipment, thus keeping interconnect cabling as short as possible. It may be placed on a shelf or in a cabinet where it's convenient to operate.
Résumé du contenu de la page N° 12
Voltage selection The PLS-226 is factory-set (internally) for 100V, 120V, 200V, 220V, or 240V AC mains operation @ 50 or 60Hz. Make sure that the label on the bottom of the PLS-226 indicates the correct AC operating voltage for your location. PLS-226 bottom-panel PLS-226 POWER SUPPLY label DC OUTPUTS AC INPUT WARNING: BEFORE ATTEMPTING TO OPERATE THIS DEVICE, REFER TO OWNER'S MANUAL FOR PROPER OPERATING INSTRUCTIONS AND SAFETY PRECAUTIONS. HAZARDOUS VOLTAGE Voltage AVAILABLE INSIDE; DISCONNECT A
Résumé du contenu de la page N° 13
Set-up and installation Connectors and cables The Nº26 incorporates RCA-type and XLR-type connectors for audio signal input and output. The Madrigal-designed RCA-type connectors used for single-ended audio interconnection are a great improvement over ordinary RCA- type connectors. The gold-plated XLR-type connectors employed are of European design, and are made to professional standards. When connecting the Nº26 to source equipment and power amplifiers, we recommend Madrigal Audio Laboratories H
Résumé du contenu de la page N° 14
Internal adjustments: The high-gain and low-gain phono options offer internally selectable cartridge loading cartridge loading via two four-pole miniature rocker switches, one for each channel. The high-gain and low-gain options have been factory- adjusted at 825Ω and 47KΩ , respectively. If you wish to change the factory-adjusted cartridge loading, see "Making the internal adjustments;" refer to the table below for the proper switch positions for each load setting. Cartridge loading settings Sw
Résumé du contenu de la page N° 15
Internal adjustments: If you wish to vary the input capacitance of the phono option to varying the input obtain the optimal value for a particular cartridge, a capacitor may capacitance also be inserted into the optional load terminals (see "Terminating the optional load" and "Making the internal adjustments"). Because the inherent input capacitance (all switches off) is in parallel with the optional load terminals, use the following formula to calculate the actual capacitor needed. C = C - C -
Résumé du contenu de la page N° 16
2. Using a 3/32" Allen key, remove the four 4-40 socket-head cap screws securing the end caps on the read of the Nº26's chassis. 3. Using a Phillips screwdriver, remove the four 4-40 screws securing the Nº26's top plate. Carefully slide the top plate to the rear and remove it. 4. Adjust the gain switches (using a ballpoint pen or similar instrument) and install optional loads as desired. 5. Reassemble the Nº26. Power connection and Be sure all associated equipment is disconnected from the AC mai
Résumé du contenu de la page N° 17
Care and maintenance To remove dust from the cabinet of the Nº26, use a feather duster. To remove dirt and fingerprints, we recommend isopropyl alcohol and a soft cloth. 11
Résumé du contenu de la page N° 18
Specifications The correlation between published specifications and sonic quality is unreliable. A list of numbers reveals virtually nothing. All technical measurements must be subject to qualitative as well as quantitative interpretation. Measurements of the Nº26 yield excellent results by any standards. However, only those specifications that apply to its actual operation are included here. Power consumption: 50W maximum, depending on options Mains voltage: 100V, 120V, 200V, 220V, or 240VA
Résumé du contenu de la page N° 19
Dimensions 3/8" (9.5) 7/64" (2.5) 1-1/8" Dimensions, Nº26, top view (28.7) 3/4" dia. (19.1) 17-19/64" (439.4) 15-3/64" 17-1/2" (382.0) (444.5) 1-1/4" 10-1/2" (31.8) (266.7) 13-1/8" (333.4) Dimensions, Nº26, side view 2-35/64" 2-3/4" (64.8) (69.9) 7/16" 7/64" (11.1) (2.5) 13
Résumé du contenu de la page N° 20
3/8" (9.5) 7/64" (2.5) Dimensions, PLS-226, 1-1/8" (26.7) top view 3/4" dia. (19.1) 7-13/32" (187.9) 7-39/64" 5-9/64" (193.0) (130.6) 1-1/4" 10-1/2" (31.8) (266.7) 13-1/8" (333.4) Dimensions, PLS-226, side view 2-35/64" 2-3/4" (64.8) (69.9) 7/16" 7/64" (11.1) (2.5) 14
