Résumé du contenu de la page N° 1
CkJEGFSISwRPoTrDPlFiCzNrChK
Dual Projection System
Dual Projection System
XJ-SK600
XJ-SK600
Be sure to read the precautions in the “YA-S10 Setup Guide” that comes with the
English Dual Projection System.
Be sure to keep all user documentation handy for future reference.
To obtain the latest version of this manual visit the website at the URL to the left.
Setup Guide
Lesen Sie unbedingt die wichtigen Hinweise und Vorsichtsmaßregeln in der zum
http://world.casio.com/manual/pr
Résumé du contenu de la page N° 2
Contents XJ-SK600 Overview.................................... E-2 Configuring the Initial Settings of the Two Projectors..................................... E-8 Unpacking ......................................................E-2 Configuring Initial Control Box Settings ...... E-10 General Guide ................................................E-3 Adjusting the Positions of Getting Ready ............................................. E-4 the Two Projectors................................... E-1
Résumé du contenu de la page N° 3
XJ-SK600 Overview The XJ-SK600 Projector System uses a Control Box to sync two projectors so their output looks and acts as if it is coming from a single projector. A powerful collection of projected image shaping functions, enables clear image projection not only onto a flat screen, but also onto curved and irregular surfaces. IImpor Impor mportant! tant! tant! After the Projector System has been installed and adjusted, do not alter the cabinet position or positions of the projectors inside
Résumé du contenu de la page N° 4
XJ-SK600 Overview General Guide Projectors Control Box Cabinet Zoom ring Smaller Larger Focus ring E-3
Résumé du contenu de la page N° 5
Getting Ready Installation Location The Projector System can be placed on a flat surface or it can be ceiling mounted. Placing the Projector System on a Flat Surface When placing the Projector System on a flat surface, you need to install the four feet on the bottom of the cabinet. Screw each of the feet into the holes at the corners on the bottom of the cabinet. After attaching the feet to the cabinet, place the cabinet onto a table, desk, or stand or other level and firm surface, making su
Résumé du contenu de la page N° 6
Getting Ready Location Precautions Use a conveniently located power outlet that you can reach easily when you need to unplug the power cord. Projector Make sure there is nothing inside the area (within 30 cm 30cm (11.8") (11.8 inches) of the Projector System) indicated by the nearby illustration. Take particular care to ensure that Cabinet Intake vents there is nothing blocking the flow of air from the projector exhaust vents. Airflow from air conditioning equipment redirecting heat Exh
Résumé du contenu de la page N° 7
Getting Ready Ceiling Installation The Projector System can be hung from a ceiling. The Projector System can be ceiling mounted in an inverse (upside down) configuration or a vertical configuration. IImpor Impor mportant! tant! tant! To protect against sudden accidental dropping of the Projector System from a ceiling mount configuration, be sure to secure the cabinet to ceiling fixtures with wires or some other adequate means. When ceiling mounting in a vertical configuration, make sure the
Résumé du contenu de la page N° 8
Getting Ready Wiring Wire the Control Box and two projectors inside the Cabinet as shown in the illustration below. Projector A (Side nearest the Control Box) Ferrite core Control Box side Use the supplied Use a supplied RS-232C power cord to plug cable to connect. into an outlet. Use a supplied HDMI cable to connect. Projector B (Side furthest from the Control Box) When connecting the Control Box to a projector using a supplied HDMI cable, connect the plug of the cable that is nearest the f
Résumé du contenu de la page N° 9
Getting Ready Preparing the Remote Controllers Load two AAA-size alkaline batteries into each of the remote controllers: one YT-200 Control Box remote controller, one YT-120 projector remote controller. Batteries are provided with the Projector System. To load batteries: Open the battery cover on the back of a remote controller. Load the batteries making sure their poles (+/–) are facing in the correct directions. Finally, replace the battery cover. Impor Impor Important! tant! tant! To avoid
Résumé du contenu de la page N° 10
Getting Ready 7. On the remote controller, press the [MENU] key to display the setup menu, and then configure the settings below in the indicated sequence. Setting Item Setting (1) Option Settings 1 Auto Keystone Correction Off 3 (2) Screen Settings Keystone Correction 0 3 (3) Screen Settings No Signal Screen Black 3 (4) Input Settings Signal Name Indicator Off 3 (5) Option Settings 1 Auto Power Off Off 3 If the Projector System will be used in an inverted ceiling mount configuration, sel
Résumé du contenu de la page N° 11
Getting Ready Configuring Initial Control Box Settings After you finish configuring the initial settings of the two projectors, perform the procedure below to configure initial Control Box settings. Perform the operations below using the Control Box remote controller (YT-200). Note that these operations cannot be performed using the projector remote controller (YT-120). To configure initial Control Box settings 1. Press the remote controller [ALL] key (or [1] key) to turn on Control Box power.
Résumé du contenu de la page N° 12
Getting Ready Adjusting the Positions of the Two Projectors Use the procedure in this section to adjust the projected images of the two projectors so they are approximately the same size and at the same position on the target screen (the screen, wall, or other surface to be used as the projection surface after setup of the Projector System is complete). After you finish configuring the initial settings of the Control Box, perform the procedure below. For information about which projector is
Résumé du contenu de la page N° 13
Getting Ready 5. Perform the steps below to adjust the position and size of the Projector B image so it slightly runs off the edges of the target screen, as shown in the “After adjustment” image above. (1) Adjust the zoom ring of Projector B. (2) Loosen the five screws that secure the cabinet side panels, and then rotate the adjuster knob to adjust the orientation. Take care simply to loosen the five screws. Do not remove them. Fixing screws Adjuster knob Fixing screws After adjusting the p
Résumé du contenu de la page N° 14
Getting Ready 8. On the “Image Shaping” menu that appears, select “Adjust Image Position” and then press the [ENTER] key. This will project two adjustment patterns, a yellow one for Projector A and a light blue one for Projector B. Use the focus rings of Projector A and Projector B to adjust the focus of the patterns as required. Impor Impor Important! tant! tant! All of the explanations in this manual assume that Projector A is connected by HDMI cable to OUTPUT A of the Control Box and th
Résumé du contenu de la page N° 15
Getting Ready 15. Next, perform the procedure in the separate YA-S10 Setup Guide under “Shaping the Image to Match the Projection Screen”. Impor IImpor mportant! tant! tant! During the adjustment procedures from this point onwards, do not alter the cabinet position or positions of the projectors inside the cabinet, the zoom ring setting, the focus ring setting, or the screen position. If any one of these is altered, return to step 2 of the procedure and perform the other steps again. E-14
Résumé du contenu de la page N° 16
Product Specifications Model Name XJ-SK600 Brightness Approximately 6000 lumens Environment Operating temperature: 5 to 35°C Operating humidity: 20 to 80% (non-condensation) Operating altitude: 0 to 2,000 meters above sea level Power Requirements Projector: 100VAC - 240VAC, 50/60Hz Control Box: AC adapter (100VAC - 240VAC, 50/60Hz) Power Consumption Each Projector: 190W (Eco Mode: Off (Bright)) Control Box: 10W Weight Approximately 18.3kg (40.3lbs) (Not including accessories) Approximate Dimensi
Résumé du contenu de la page N° 17
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructio
Résumé du contenu de la page N° 18
Batterij niet weggooien, maar inlevern als KCA Manufacturer: CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan Responsible within the European Union: CASIO EUROPE GmbH Casio-Platz 1, 22848 Norderstedt, Germany
Résumé du contenu de la page N° 19
Printed in China Imprimé en Chine MA1303-A RJA528115-001
