Résumé du contenu de la page N° 1
PLTV65R
OWNER'S MANUAL
Mobile Audio/Video System
AM/FM/MPX/TV-Tuner
PLL Synthesizer Stereo Radio
Built In Amplifier
Vertical Adjustable And Horizontal Rotatable Panel
Automatically Memory Storing
TFT Monitor
Remote Control
Optional TV Tuner (Separate Box)
CD Cha
Résumé du contenu de la page N° 2
CONTENTS Important Safety Instruction 3 Automatic memory storing& 4 Installation program scanning 13 DIN Front-Mount (Method A) 4 13 Local/distant 4 Installing the unit Mono/stereo 13 Removing the unit Scan 13 5 CDC operation 13 DIN Rear-Mount (Method B) 6 13 Switching to CDC mode Wiring Connection 7 13 8 Selecting tracks Operation 13 Pausing playing Location and function of keys 8 13 Previewing all tracks 10 Switching on/off the un
Résumé du contenu de la page N° 3
IMPORTANT SAFETY INSTRUCTION CAUTION: Please read and observe all warnings and instructions given in this owner's manual. Keep these instructions. Retain this booklet for future reference. Please read the following safety instructions carefully. 1.This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit protect you if you observe the following procedures
Résumé du contenu de la page N° 4
INSTALLATION TAKE OUT SCREW BEFORE Notes: INSTALLATION Choose the mounting location where Before install the unit, please remove the unit will not interfere with the the two screws on the back of the unit. normal driving function of the driver. Take out screw Before finally installing the unit, before installation. connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure
Résumé du contenu de la page N° 5
INSTALLATION (Tapping Screw (5x25mm) and Plain Sleeve Washer) to attach the other end of L Key Outer Trim Ring metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. R Key Hex Nut Spring Washer Metal Strap 5. Mount the sleeve by inserting the Mounting Bolt sleeve into the opening of the Plain Washer dashboard and bend open the tabs Tapping Screw located around the sleeve with a screwdriver. Not all tab
Résumé du contenu de la page N° 6
INSTALLATION DIN REAR-MOUNT (Method B) 3 1 2 4 5 1. Factory radio mounting bracket 2. Car radio mounting bracket 3. Screw 4. After aligning the car radio mounting bracket with the factory radio mounting bracket, tighten the screws (5x5mm) at 2 places on each side. 5. When fix the factory radio mounting bracket with the screws, use s standard-tipped screwdriver to open the tabs of the car radio mounting bracket to make them fit into theholes in the factory radio mounting bracket.
Résumé du contenu de la page N° 7
ELECTRICAL CONNECTION MAIN UNIT ANTENNA CONNECTOR CD CHANGER CONNECTOR SOCKET (BLACK) Rch RED AV2 IN Lch WHITE VIDEO YELLOW (RED) (GREY) Rch RED AV OUT (GREEN) Lch WHITE VIDEO YELLOW R.G.B. IN (BLUE) (OPTIONAL) (YELLOW) EXTERNAL REMOTE CONTRL To the TV unit SYNC IN with the 13-pin din Jack (SEPARATE BOX) (OPTIONAL) PINK BRAKE 1 IGNITION ORANGE RED SWITCH (ACC+) BRAKE 2 MEMORY/ YELLOW BLUE POWER BATTERY(B+) BLACK ANTENNA GROUND (B-) WHITE GREY + + FRONT Rch FRONT Lch - SPEAKER - SPEAKER GREY/B
Résumé du contenu de la page N° 8
OPERATION LOCATION AND FUNCTION OF KEYS 6 8 7 28 29 30 15 31 32 33 14 13 11 9 10 1 2 16 12 4 17 3 18 Fig.A 5 23 22 19 20 21 26 25 27 24 Fig.B 8
Résumé du contenu de la page N° 9
OPERATION LOCATION AND FUNCTION OF KEYS 34 35 37 36 38 40 39 41 42 43 44 46 45 47 49 48 51 52 53 50 / 1. 27. 4:3/16:9 Selector 2. OPEN/CLOSE 28. PAU(For CDC Version Only) 3. MUTE 29. INT(For CDC Version Only) 4. LCD 30. RPT(For CDC Version Only) 5. TFT Monitor 31. RDM(For CDC Version Only) 6. SEL 32. CD-(For CDC Version Only) 7. VOLUME 33. CD+(For CDC Version Only) 8. VOLUME 34. POWER 9. Reset 35 OPEN 10. IR 36. 0~9 Numeric Button 11. BND 37. M1~M6 12. MODE 38. LOC 13. TUNING 39. -/--
Résumé du contenu de la page N° 10
OPERATION SWITCHING ON/OFF THE UNIT / Switch on the unit by pressing POWER button (1) on the front panel or POWER button (34) on the remote control. When system is on, press it again to turn the unit off. OPEN/CLOSE THE MONITOR AND Fig.3 ANGLE ADJUSTMENT Return the monitor to the central Press OPEN/CLOSE button (2) on the viewing position, then press front panel or point the remote control OPEN/CLOSE button (2) on the to IR (10) on the front panel an
Résumé du contenu de la page N° 11
OPERATION REMOTE SENSOR OPERATING WHEN THE MONITOR There is a remote sensor IR (10) on the NOT STRETCHING OUT front panel. On the monitor, there is When the monitor doesn't stretch out, another remote sensor IR (26) to the front panel of the unit is in state A receive remote control signal. You can (see Fig.A), you can operate the unit point the remote control handset to IR following the instructions below. (10) (when the monitor doesn't stretch Sound mode selection out) or IR (26) (when th
Résumé du contenu de la page N° 12
OPERATION Adjusting the loud LCD remains the previous state and the In loud mode, use VOLUME / clock will not appear. You should press buttons (7&8) or VOL / buttons(47) DISP button once again to display the to switch between loud on and off. clock. When LOUD on, "LOUD" will show Radio operation on the display (4). Switching to radio mode Directly press LOUD button (52) to Press MODE button (12) on the front reinforce the bass output. Press i
Résumé du contenu de la page N° 13
OPERATION signal and keep on each station for - Retrieve a Preset Station several seconds. At this time, press Press any one of the buttons (15) any one of the buttons (15) on the on the front panel or (37) on front panel or (37) on remote control, remote control to retrieve a the current scanned station will be station which had been stored in stored into the corresponding number the memory in advance the button, then it keeps on scanning chosen nu
Résumé du contenu de la page N° 14
OPERATION Press MO/ST button (16) on the front OPERATING WHEN THE MONITOR panel or ST/MO button (53) on remote STRETCHING OUT control to select "MONO" or "STEREO". When the monitor stretches out, the front panel of the unit is in state B (see FM1 98.10 MHz Fig.B), you can operate the unit by MONO LOC using the current menu displayed on the VOLUME 30 M1 87.50 6.5 inch color TFT display (5). BASS 2 M2 90.10 And if the unit is connected to other TV TREBLE 2 M3 98.10 unit through the cable wit
Résumé du contenu de la page N° 15
OPERATION Directly press TUNING/TRACK button Then you can press VOL / buttons (14) on the panel to move to the s (48) to select hour or minute and press previou track; press TUNING/TRACK TUN/CH / buttons (47) to change the button (13) on the panel control to move corresponding item. to the next track. Menu Control operation in CDC mode TV operation (when the unit is Press MODE button (12) on front panel connected to other TV unit through or MODE button (43) to select CDC the cabl
Résumé du contenu de la page N° 16
OPERATION display, you can press "1 "button Volume adjustment then press "6" button to select 16 Press VOLUME / buttons (23&22) channel. or VOL / buttons (47) to adjust Menu control operation volume level. In TV mode: Screen display Press MENU button (19) or (45). The Press DSP button (20) on the front menu will show on the display (5). panel or DISP button (44) on remote control to display the current status (For the unit with NTSC system): such as TVch /AV1/A
Résumé du contenu de la page N° 17
SPECIFICATION GENERAL Power Supply Requirements : DC 12 Volts, Negative Ground Maximum Output Power : 4x40 watts Current Drain : 15 Ampere (max.) TV Monitor Screen Size : 6.5" TFT Resolution : 1440 x 234 dots TV Sensitivity : 45dB V @CH25 in average RADIO FM Frequency Coverage
Résumé du contenu de la page N° 18
MOBILE TV TUNER UNIT 18
Résumé du contenu de la page N° 19
CONTROL & FUNCTION KEYS 1 3 2 This unit can't be used separately and it must be used with other special system with the 13 -pin cable. The unit is connected to another system through the 13-pin din socket (3). And the unit can receive TV signal through the antenna input jack (2). 1 POWER INDICATOR LIGHT When the unit is connected to the other system with the 13-pin din cable and the other system turns on, the power indicator light (1) will be illuminated red and the unit
Résumé du contenu de la page N° 20
www.pyleaudio.com 88-T1690-04
