Résumé du contenu de la page N° 1
Model APS-997C
Owner’s Manual
5 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
IMPORTANT! In order to provide you with the highest level of security to your
vehicle, this system is equipped with selectable manual override circuitry. It is
possible that you will need to override you security system if the transmitter
becomes lost, or inoperative due to battery failure. Reading the sections on
"Manually Overriding Your System" is necessary to fully understand t
Résumé du contenu de la page N° 2
7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming Intrusion Alert With Memory Instant Siren Activation Starter Disable Output Additional Engine Immobilizer Output, (Optional Relay Required) True Last Door Arming (Hardwire Only) Defective Zone By-Pass Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared) 6 Tone Mini Siren Car Horn Output For Additional Alarm Response (Improved Timing To Minimize RF Interference.) Additional Negative Tri
Résumé du contenu de la page N° 3
keychain transmitter and re-transmit at a later time to disarm your system. Your Keeloq Code Hopping transmitters will change their signal every time the button is pressed, so when a thief grabs then re-transmits your signal, the alarm system will not respond. If your transmitter button is pressed more than fifty times while it is out of range of the vehicle (children playing with your keys), the transmitter will not operate when you return to the vehicle, and will need to be re-aligned to the r
Résumé du contenu de la page N° 4
Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. Closing the hood, trunk, or doors will correct the problem and you do not need to disarm the system to make the correction. Doors Lock - Optional NOTE: If the optional Headlamp illumination feature has been added, and has been selected for operation when arming, as an ad
Résumé du contenu de la page N° 5
Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. NOTE: If the optional interior illumination circuit was installed, the interior light will flash as well for the full 30 second alarm cycle. DISARMING THE SYSTEM NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. NOTE:
Résumé du contenu de la page N° 6
If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered. Siren will not sound. If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before turning the key on, examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered. Doors Unlock - Optional 2 Step Doors Unlock - Optional NOTE: If the optional H
Résumé du contenu de la page N° 7
NOTE: Always remember to return the vehicle to the valet off position. This will ensure that the vehicle remains protected at all times. MANUALLY OVERRIDING YOUR SYSTEM: Using The Receivers Push-Button Override Switch Your Security System can be disarmed without the use of the keychain transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. If your system has been selected for Valet Switch manual override as indica
Résumé du contenu de la page N° 8
3. Within 10 seconds, press and release the Receivers push-button switch, 3 times. 4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5. Within 10 seconds, begin to press and release the Receivers push-button switch to set the tenths digit. (As per the example, press and release 5 times to set the tenths digit to 5) 6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off then on
Résumé du contenu de la page N° 9
NOTE: Your system must be programmed by the installation center to en- able this feature. NOTE: Whenever the chirps are bypassed, the 4-chirp intrusion indicator and 3 chirp defective zone indicator will always operate. Since these are important warnings to you that something has happened, they cannot be eliminated. NOTE: Your system must be programmed by the installation center to en- able this feature. REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions
Résumé du contenu de la page N° 10
NOTE: Setting the stage of the shock sensor will be effective for one arming cycle only. Once the system has been disarmed, the very next arming cycle will cause the sensor to default to the normal operation stage. To change or adjust the shock sensor, press and release the ARM button of you keychain transmitter. 1. Within 2 seconds of arming, press and release the ARM button 1 time, to defeat the pre-detect stage of the shock sensor. (The lights will flash and the siren will chirp once.) 2.
Résumé du contenu de la page N° 11
To Remote Start The Vehicle: Press and release the programmed channel of your keychain transmitter two times within 2 seconds. The vehicle will start and remain running for the pre- programmed 5, 10, 15, or 20 minutes. As a visual indication, the parking lights will flash or turn on depending on the programming set up by your installation center. When you arrive at your vehicle, disarm the alarm system by pressing and re- leasing the arm/disarm button of your keychain transmitter. Enter the
Résumé du contenu de la page N° 12
3. Within 10 seconds of step 2, activate the RF start command two times. (Push the second channel button of your keychain transmitter 4 times). The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated. CANCELING THE AUTOMATIC START UP TIMER To cancel the automatic start up timer do one of the following; 1. Start the vehicle manually with the use of the ignition key and depress the brake pedal. 2. Remote start the vehicle using your keychain RF
Résumé du contenu de la page N° 13
Remote Car Starter Remote Window Closure Remote Garage Door Interface To remotely operate the device indicated, momentarily press, or press and hold the appropriate transmitter button(s) as indicated above. ADDITIONAL REMOTE FUNCTION ( CHANNEL 6 ) Channel 6 is an alternate output that can be controlled by the unlock button of the transmitter, or by and independent button or combination of buttons. For your ve- hicle this output is: Controlled By: Trunk/Key Button Option Button Lock
Résumé du contenu de la page N° 14
To activate the turbo timer: Anytime the engine is running for more than 15 seconds: 1) Place the gear selector in park. 2) Set the parking, (hand), brake. 3) Be certain your foot is off the brake pedal. 4) Press the receiver's program/Push-Button switch 2 times within 5 seconds. The parking lights will flash two times indicating the mode was successfully entered. If your parking lights flashed four times, this indicates the turbo mode was on and is now turned off. With the turbo timer mode sele
Résumé du contenu de la page N° 15
NOTE: Engine can be started in many modes armed, disarmed, valet, etc... The screen shown is Locked/ Armed and running. When the Panic Mode has been activated and the system is armed the vehicle's lights will flash, the siren and lock icon will be displayed on the LCD screen and the siren will beep. If the system is disarmed and the Panic Mode is activated, the lights will flash unlock icon will be displayed and the siren will beep on the LCD screen. When ever the vehicle is operated from the tw
Résumé du contenu de la page N° 16
When the vehicle is armed, and a door is opened, or ajar, the transmitter will chirp 3 times, the lights will flash, and the display will indicate a door trigger as shown on the previous page. When the door is closed or the zone clears, the transmitter will chirp 1 time, and the display will clear. When the vehicle is armed, and the hood or trunk, is opened or ajar, the trans- mitter will chirp 3 times, the lights will flash, and the display will indicate a hood or trunk trigger as shown on the
Résumé du contenu de la page N° 17
ADDITIONAL REMOTE FEATURES: The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display, toggle the transmitter from beep tones to vibrate mode, initiate daily start timer, and temperature start. Selec- tion of these and other features are shown below: NOTE: Transmitter must be within operating range of the vehicle, approximately 1000 ft. Check Vehicle Status: Press the lock+key+option buttons simultaneously for 1 second. The v
Résumé du contenu de la page N° 18
at the set time. To toggle this feature off, press the option + lock buttons simultaneously until a beep is heard and the 24 hr timer turns off. NOTE: The unit will start once and run for the prescribed time. If you require more frequent starting please refer to auto start up timer mode shown earlier in this guide. NOTE: To insure accurate 24 Hour Start up, it is advisable to reset the start time periodically as time may drift slightly each day. Timing Count Down: The unit offers an additional
Résumé du contenu de la page N° 19
Battery Indicator: Your transmitter has a battery indicator that is shown in the upper right corner of the screen as shown left. This icon indicates a new battery shown with 3 bars. As the battery deteriorates, the bars will disappear. 1 bar indicates the battery should be replaced. Replace battery with a fresh 1.5V AAA battery and dispose of the used battery properly. Other icons that will be displayed at times when certain functions and features are active in the vehicle or on the remote: Ra
Résumé du contenu de la page N° 20
THIS PAGE LEFT BLANK INTENTIONALLY Page 20 128-8774 20 of 24
