Résumé du contenu de la page N° 1
®
EH4014/EH4018 Series
Camera Enclosures
Installation/Operation Manual
C430M-E (1/95)
PELCO • 3500 Pelco Way • Clovis, CA 93612-5699 • USA • www.pelco.com
(800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827
PELCO Manual C430M-E (1/95) 13
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Section Page 1.0 WARNINGS ......................................................................................................................................... 1 2.0 SCOPE................................................................................................................................................. 2 3.0 DESCRIPTION..................................................................................................................................... 2 3.1 M
Résumé du contenu de la page N° 3
REVISION HISTORY Manual # Date Comments C430M 11/88 Original version. C430M 4/90 Rev. A. Added EH4014-1/-2, EH4014/BR, EH4014/CH, EH4014/CP, EH4018-1/-2, and BK4000/BK4024 models. Fig- ure 2 revised to show current design. Sections 4.2.1 and 4.2.2 revised to include new cable distances and heater kit installation procedures. Section 7 updated to include addi- tional hardware. C430M 9/90 Rev. B. Manual revised to include Section 1.1 for the UL compliance and listing. 11/90 Addendum issued for add
Résumé du contenu de la page N° 4
(This page intentionally left blank.) iv PELCO Manual C430M-E (1/95)
Résumé du contenu de la page N° 5
INSTALLATION/OPERATION MANUAL EH4014/EH4018 SERIES CAMERA ENCLOSURES 1.0 WARNINGS Prior to installation and use of this product, the following 4. Only use replacement parts recommended by WARNINGS should be observed. PELCO. 1. Installation and servicing should only be done by 5. After replacement/repair of this unit’s electrical Qualified Service Personnel and conform to all components, conduct a resistance measurement Local codes. between line and exposed parts to verify the exposed parts have
Résumé du contenu de la page N° 6
2.0 SCOPE 3.0 DESCRIPTION The information contained within this manual covers The EH4014 and EH4018 light-duty camera enclosures the EH4014/EH4018 Series camera enclosures. are designed for use with 2/3" cameras and will ac- commodate fixed focal length lenses or motorized zoom lenses with or without auto-iris operation. The EH4014 and EH4018 have been engineered for indoor and outdoor use when used in accordance with the installation instructions of this manual. They are of contemporary desig
Résumé du contenu de la page N° 7
3.1 MODELS 3.2 OPTIONS EH4014 Enclosure, indoor/outdoor extruded AFW4000 Anti-fogging window aluminum construction for 2/3" cam- eras and fixed focal length lenses up BK4000 Blower kit for EH4014/EH4018, 120 to 12" long. (UL, CE) VAC, 4 watts EH4014-1 Same as EH4014 except maximum BK4024 Blower kit for EH4014/EH4018, 24 camera/lens length is 10.25" and unit VAC, 3 watts is supplied with 120 VAC heater/ blower. (UL) BK4220 Blower kit for EH4014/EH4018, 230 VAC, 4.8 watts EH4014-2 Same as EH4014
Résumé du contenu de la page N° 8
3.3 RECOMMENDED CABLE SIZE The following cable sizes are the minimum recom- mended for use with the combination of blower/heater/ CAUTION: When using a single power camera. source for both the camera and accessories, the camera power consumption must be taken into consideration when determining wire gauge. Power Model Number Input Voltage Consumption Cable Size Cable Distance EH4014-1/ 120 VAC 44 watts 22 Awg 1,013 ft (308.8 m) EH4018-1 20 Awg 1,612 ft (491.3 m) 18 Awg 2,564 ft (781.5 m) 16 Awg
Résumé du contenu de la page N° 9
3.4 SPECIFICATIONS Weight: EH4014 4 lbs. 4 oz. (1.91 kg) MECHANICAL EH4014-1 5 lbs. (2.25 kg) EH4014-2 5 lbs. (2.25 kg) Camera EH4014-3 5 lbs. (2.25 kg) Mounting: Multiple holes on camera sled EH4018 5 lbs. (2.25 kg) EH4018-1 5 lbs. 12 oz. (2.59 kg) Camera Size: Accommodates camera/lens combi- EH4018-2 5 lbs. 12 oz. (2.59 kg) nations up to: EH4018-3 5 lbs. 12 oz. (2.59 kg) 5.25" W x 3.50" H x (EH4014) 12.00" L Shipping (EH4018) 16.00" L Weight: (EH4014-1/EH4014-2/EH4014-3) 10.25" L EH4014 6
Résumé du contenu de la page N° 10
4.0 INSTALLATION 8. Replace the two (2) Phillips head screws. The following hardware is supplied with the enclosure IMPORTANT: When reinstalling the front and can be used to mount the enclosure or the camera/ or rear of the enclosure, make sure the end caps lens. are firmly seated against the enclosure to in- sure proper sealing. Quantity Item 9. Attach the enclosure to the appropriate mount or 3 1/4-20 x .500 Hex head screws pan/tilt using the instructions provided. 3 1/4 Flat washers 3 1/4 Sp
Résumé du contenu de la page N° 11
4.2 HEATER KIT INSTALLATION 4.3 BLOWER KIT INSTALLATION Refer to Section 2.4, Recommended Cable Size, to de- To install the BK4000/BK4024, perform the following termine cable size needed for installation. To install the steps: heater and/or blower kits perform the following steps (refer to Figure 2): 1. Remove the Phillips Head screws from the rear cap and slide the assembly out from the enclosure. 1. Remove the Phillips head screws from the rear cap and slide the assembly out from the enclosu
Résumé du contenu de la page N° 12
4.4 INSTALLATION PROCEDURES The following items are supplied in the heater and blower kits. Quantity Item PELCO Part No. Blower Kit Heater Kit 1 PCB and blower bracket BK40004000COMP X X 1 PCB and thermostat assy (24V/120V) PCB9000300ASSY X 1 PCB and thermostat assy PCB9100300ASSY X 4 PCB mounting screws, 6-32 x 3/8 ZH6-32X.375SPP X 4 PCB insulating washers ZH200X437X62N X 1 Heater bracket (24V/120V) HK40244000COMP 24/120 VAC models 1 Heater bracket (230V) HK2304000COMP 230 VAC model 1 Heater
Résumé du contenu de la page N° 13
4.5 SUN SHROUD INSTALLATION 5. Put the cap back on the enclosure and fasten down with the screws. The sun shroud protects the enclosure from the direct rays of the sun and reduces internal temperature by NOTE: Be sure the screws are tightened down approximately 10-15°. To install the sun shroud, per- to secure the seal between the cap and the en- form the following steps (refer to Figure 4). closure. 1. Remove the two (2) screws from the front or rear end cap of the enclosure. 5.0 CARE AND MAI
Résumé du contenu de la page N° 14
6.0 EXPLODED ASSEMBLY DIAGRAM/ PARTS LIST The following parts list corresponds to the exploded assembly diagram in Figure 5. Item Quantity Description Part Number 1 2 Gasket, front/rear (not shown) EH400010000 2 1 Front cap, black EH400010006 3 2 Gland, SL9 EH400010003 4 2 Counter nut, GMP-9 EH400010004 5 1 Sled bracket EH40004007COMP 6 1 Rear end cap, black EH400010005 7 1 Body, 14" enclosure (EH4014 only) EH40144000COMP 1 Body, 18" enclosure (EH4018 only) EH40184000COMP 8 1 Sled (EH4014) EH40
Résumé du contenu de la page N° 15
7.0 WARRANTY AND RETURN INFORMATION WARRANTY RETURNS Pelco will repair or replace, without charge, any merchandise proved In order to expedite parts returned to the factory for repair or credit, please defective in material or workmanship for a period of one year after the date call the factory at (800) 289-9100 or (559) 292-1981 to obtain an of shipment. authorization number (CA number if returned for credit, and RA number Exceptions to this warranty are as noted below: if returned for repair).
Résumé du contenu de la page N° 16
® PELCO 3500 Pelco Way • Clovis, CA 93612-5699 • www.pelco.com (559) 292-1981 • (800) 289-9100 • FAX (559) 292-3827 or (800) 289-9150 International customers call 1-559-292-1981 or FAX 1-559-348-1120 (Product specifications subject to change without notice.) 12 PELCO Manual C430M-E (1/95)
