Instruction d'utilisation PYLE Audio PDWM5300

Résumé du contenu de la page N° 1

PDWM 5300 PDWM 5300
U UH HF F P PL LL L D Div ive ers rsit ity y W Wir ire ele les ss s U UH HF F P PL LL L D Div ive ers rsit ity y W Wir ire ele les ss s
M Mic icro rop ph ho on ne e S Sy ys ste tem m w w/ / L LC CD D M Mic icro rop ph ho on ne e S Sy ys ste tem m w w/ / L LC CD D
PDWM5300 PDWM5300
OPERA OPERATION MANUAL TION MANUAL OPERA OPERATION MANUAL TION MANUAL

Résumé du contenu de la page N° 2

Thank you for buying the PDWM5300 Wireless System. Please Avoid exposure of the system to rain or moisture. read through these operation instructions so you will know how No user-serviceable parts inside the system. Refer all servicing to a qualified to operate your model properly. After you read it, put it away in a technician only. safe place for future reference. Handle the wireless system carefully, dropping or other shocks may cause failure. Avoid using the system

Résumé du contenu de la page N° 3

PARTS DESCRIPTION 1. Mesh: cartridge inside 6 2. Tube 3. Power LED indicator 4. Power and Mute switch: Switch on and off the microphone. Move the switch to middle position to mute the mic. 5. Battery compartment 6. Battery Cover + 7. CH selector ON - OFF + OPERATION 1. Unscrew the battery cover at the end of the microphone. Install the - provided 2 1.5V batteries, taking care to fit it with the correct polarity ON DIP 1234 connected. 7 2. According to frequency Chart on the battery

Résumé du contenu de la page N° 4

PARTS DESCRIPTION 1. Power Switch: Turn on power switch, the display of LCD will illuminate. 2. Power LED indicator: Turn on power switch, this indicator will illuminate. 3. SET: Press once to adjust frequency by UP/DOWN buttons. Press again to exit. 4. UP: Channel UP 5. DOWN: Channel DOWN 6. LCD Display 7. Volume control 8. Antenna A and B CH00 795.2MHz 9. Balanced output 00dB AF 10. Unbalanced output 11. 12V DC IN OPERATION 1. Connect the antennas A and B. Make sure they are vertical. 2

Résumé du contenu de la page N° 5

Using the supplied audio cable, connect from the AF OUT jack socket to the LINE IN socket on amplifier. Alternatively, you can connect an XLR cable to the XLR balanced output. Connect the mains power adaptor from "DC 12V" jack to a suitable mains power socket. Installation Location: At least 3 ft. above ground level At Least 3 ft. away from wall MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE 4

Résumé du contenu de la page N° 6

The wireless microphone is not Turn on the wireless microphone turned on. The microphone receiver is not Turn on the microphone receiver turned on. The on air and the connected audio equipment indicator does Turn on the microphone receiver The microphone receiver is not not light up connected properly. and the connected audio equipment Frequency not set correctly. Make sure mic and receiver are set to the same frequency. The battery in the wireless Replace the battery. microphone is

Résumé du contenu de la page N° 7

A. Overall System Carrier Frequency: UHF 795~805MHz Frequency Stabilization: less than 30ppm Dynamic Range: more than 90dB Total Harmonic Distortion: less than 0.5% Frequency Response: 40hz~15khz 3dB Audio Output Level: separate type:0~ 400mV Mix Type: 0~ 200mV B. Receiver Power Supply: DC 12V Consume Power: 4W Signal/Noise Ratio: