Résumé du contenu de la page N° 1
2005 Hutchison Harbour Ring Enterprises Limited This device complies with Part 15 of the FCC Rules.
All rights in this publication are reserved and no part may Operation is subject to the following two conditions:
be reproduced without the prior written permission of (1) this device may not cause harmful interference, and
i.Tech Clip V
the publisher. The contents of this publication are (2) this device must accept any interference received,
believed to be correct at the time of going to pr
Résumé du contenu de la page N° 2
Table of Contents Voice Dialing from Your Headset ..................................................................................................................... 11 i.Tech Clip V Overview ...................................................................................................................................................... 1 Last Number Redialing from Your Headset ................................................................................................... 12 Getting
Résumé du contenu de la page N° 3
i.Tech Clip V Overview Getting Started 1 1. Microphone 6 2 2. Volume Key 3. Status Indicator 3 7 To use your i.Tech Clip V (“the headset”), please follow 4. Built-in Buzzer these simple steps: 5. Charging Socket 5 4 6. Built-in Rechargeable Battery Charge your headset 8 7. Multi-function Button (MFB) Pair your headset with a Bluetooth-enabled mobile handset 8. Earphone 01 02
Résumé du contenu de la page N° 4
Charging Your Headset Charging Your Headset Connect the charger to an AC wall outlet (mains socket) and the charger plug to the headset’s charging socket (fig.1). The LED will be red while charging. IMPORTANT Charging indication will be delayed for a few seconds if the headset has not been used for a long time or the battery is drained. Charging Time Charging the battery fully is normally within 3 hours. When the battery is fully charged, the LED will turn blue and The Headset comes with a
Résumé du contenu de la page N° 5
Low Battery Turning Your Headset On and Off When the headset is on and the battery becomes low, the status indicator flashes red and the headset emits a beep every 1 minute. Please recharge the battery as described above. If you are setting up the headset and your mobile phone in a noisy environment, we advise you to put on the earphone first so that the beep will be more audible. Turning Your Headset On and Off Turning Off the Headset Press and hold the MFB for approximately 3 seconds until y
Résumé du contenu de la page N° 6
Pairing Your Headset Pairing Your Headset The headset only works with Bluetooth-enabled mobile phones. Prior to using and pairing your 1. Place the headset and the mobile handset no more then 1 meter apart and ensure there is nothing in between. headset for the first time, please check if your 2. Ensure the headset is OFF. mobile phone is Bluetooth-enabled. 3. Press and hold the MFB approximately 8 seconds until the headset status indicator alternately flashes blue and Up to 1 metre
Résumé du contenu de la page N° 7
7. Press “Return” to go back to your mobile handset’s main menu. For certain mobile handset models, a headset Ending a Call icon will be shown on the screen. You should now be able to make and receive calls using your headset. Press the MFB to end your call or end the call via your mobile handset in the normal way. IMPORTANT If the pairing cannot be completed within 2 minutes while the pairing mode is activated, the headset status indicator flashes purple followed by 3 beeps and the headset
Résumé du contenu de la page N° 8
Using Your Headset Last Number Redialling from Your Headset Short press the MFB on your headset twice. Muting the Microphone IMPORTANT The above functions are only applicable to mobile handsets with Bluetooth Handsfree Profile. You can put a call on hold by muting the microphone. Functionality varies depending on the mobile handset model you have. Please refer to your mobile handset user Press and hold the volume key for two seconds until status indicator flashes Red to mute built in Micropho
Résumé du contenu de la page N° 9
Adjusting the Volume Care and Maintenance Press the Volume Key repeatedly until you reach the desired volume level. The listening volume may be affected Headset by the volume setting of the caller’s phone as well. Re-adjust the listening volume again when necessary. • Consider turning your headset off before placing it in your pocket or bag. If the MFB is accidentally depressed, your mobile handset may place an unintended call. • Do not expose the headset to liquid, moisture or humidity as it
Résumé du contenu de la page N° 10
Safety Information Built-in Battery • Check local laws regarding use of a mobile handset and headset whilst driving. If you use the headset while • Do not attempt to replace the headset’s battery yourself as it is built into the headset and is not changeable. driving, ensure your attention and focus remain on the road and you drive in a responsible and safe manner. • Charge the battery in accordance with the instruction supplied with this user guide. • Never allow children to play with the h
Résumé du contenu de la page N° 11
Troub l esh o oting Troub l esh o oting If you are unable to connect your headset with your mobile handset or Bluetooth enabled device, please try the following: • Ensure your headset is turned on and is properly charged. • Ensure the headset is paired with your mobile handset. • Ensure your mobile handset’s Bluetooth feature is activated.Please refer to your mobile handset user guide for specific instruction. The i.Tech Clip V Headset is compliant with and adopts the Bluetooth Specification
Résumé du contenu de la page N° 12
Product Specifications Declaration of Conformity ( DoC ) We, i.Tech Dynamic Ltd., declare that the following product: Bluetooth Specification: Version 1.2 Class 2 Product Name: i.Tech Clip V Bluetooth Profile Supported: Headset and Handsfree Model No.: C51-A05054-XX Range of Frequency: 2.4GHz Spectrum Is in conformity with the following essential requirements of Council Directive 1999/5/EC ( referred to as Talk Time*: up to 6 hours R&TTE Directive ) : Article 3.1a, 3.1.b and 3.2. and the
