Résumé du contenu de la page N° 1
R
E
B
E
W
Owners Guide
DANGER
Liquid Propane Gas
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open lid
4. If odor continues, keep away from the
®®
appliance and immediately call your
gas supplier or your fire department.
Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death, or damage to property.
WARNING
1. Do not store spare liquid propane
cylinder within 10 feet (3m) of this
appliance.
2. Do not store or use gasol
Résumé du contenu de la page N° 2
DANGER Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. WARNINGS Do not store a spare or disconnected liquid propane cylinder under or near this barbecue. Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual. After a period of storage, and/or nonuse, the Weber Gas Barbecue should be checked for gas le
Résumé du contenu de la page N° 3
Warranty Weber-Stephen Products Co. (Weber) hereby warrants There are no other express warrants except as set forth to the ORIGINAL PURCHASER of this Weber Gas Grill herein and any applicable implied warranties of that it will be free of defects in material and merchantability and fitness are limited in duration to the workmanship from the date of purchase as follows: period of coverage of this express written Limited Warranty. Some regions do not allow limitation on how Aluminum Castings, lifet
Résumé du contenu de la page N° 4
Contents Danger & Warnings ................................ A-2 Warranty ................................................. A-3 General Instructions ............................... A-5 Exploded View ........................................ A-6 Parts List ................................................ A-9 Assembly Instructions ............................ B-1 Installing Features .................................. C-1 Operating ............................................... D-1 Lighting.........
Résumé du contenu de la page N° 5
Storage General Instructions • The gas must be turned OFF at the LP cylinder Your Weber Gas Barbecue is a portable outdoor when the Weber Gas Barbecue is not in use. cooking appliance. With the Weber Gas Barbecue you • When the Weber Gas Barbecue is stored indoors, can grill, barbecue, roast and bake with results that are the gas supply must be disconnected and the LP difficult to duplicate with indoor kitchen appliances. cylinder stored outdoors in a well-ventilated space. The closed lid and Fl
Résumé du contenu de la page N° 6
1 Genesis Silver-B LP 011901 2 3 27 28 4 29 5 6 7 30 8 31 9 32 33 34 35 10 36 37 11 12 38 13 14 39 15 40 16 41 17 42 18 32 43 44 19 45 20 46 21 47 22 48 23 49 24 50 25 26 51 52 A-6
Résumé du contenu de la page N° 7
1. Hinge Pin 27. Hair Pin Cotter 2. Left Endcap 28. Right Endcap 3. Shroud 29. Thermometer 4. Handle 30. Burner Control Knobs 5. Warm-Up™ Basket 31. Control Panel 6. Warming Rack 32. Control Panel Hardware 7. Cooking Grates 33. Ignitor Button 8. Flavorizer Bars 34. Crossover Tube 9. Cooking Box 35. Front and Back Burners 10. 1/4-20 keps nut 36. Center Burner 11. Slide Out Bottom Tray 37. Manifold Hardware 12. Catch pan holder 38. Manifold, Hose and regulator (assembled) 13. 1/4-20 x 1/2 inch bol
Résumé du contenu de la page N° 8
© 2001 Weber-Stephen Products Co., Weber, the silhouette, and the kettle configuration are registered trademarks ® of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL, 60067-6266, U.S.A. This product is covered by one or more United States patents and patents in other nations globally. Printed in the U.S.A. A-8
Résumé du contenu de la page N° 9
® ® ® ® ® You will need: Left Frame - 1 Screwdriver Phillips screwdriver Right Frame - 1 Hammer Wheel Frame - 1 7/16 open-end or an adjustable wrench Caster Frame - 1 Pliers Frame Connectors - 2 Block of wood Left Trim - 1 Lid - 1 Right Trim - 1 Work Surface - 1 Cooking Box - 1 Swing-Up Work Surface - 1 Hinge Rod - 1 Bottom Shelf - 1 Cooking grates - 2 Warming Rack - 1 Control panel - 1 Warm-Up Basket - 1 Flavorizer Bars - 5 A-9
Résumé du contenu de la page N° 10
Cylinder Panel - 1 Burner Control Knobs - 3 Hinge Pins (1/4 x 1 1/2 inch clevis pin) - 2 Wrap-Around Trim Piece - 1 2 inch bolts (1/4 x 20 x 2 inch bolts) - 5 1 3/4 inch bolts (1/4 x 20 x 1 3/4 inch bolts) - 2 Bottom tray - 1 1/2 inch bolts (1/4 x 20 x 1/2 inch bolts) - 8 Catch Pan Holder - 1 Keps Nut (1/4 x 20 Keps Nut) - 1 Catch-Pan - 1 Wing Nut (1/4 x 20 Wing Nut) - 2 Disposable Drip Pans - 2 Nylon Washers - 15 Thermometer - 1 Hair Pin Cotter - 2 Wheels - 2 Hubcaps - 3 Control Panel Hardware
Résumé du contenu de la page N° 11
Addendum Sheet You may have a different style manifold bracket and Spider Stopper Guard listed in your instruction manual. If you do, please follow these steps below in place of the steps included in the manual. Assembly Instructions * See Section B * Install manifold bracket You will need: manifold bracket Hook the bracket(2) onto the manifold at the center * See Section A * burner valve. Place your hand underneath the bracket. Lift the manifold and cooking box slightly, then hook the tab of th
Résumé du contenu de la page N° 12
1) The smell of gas in conjunction with the burner flames the crossover tube(1) from the burners. Remove the appearing yellow and lazy. burners from the cooking box. 2) Barbecue does not reach temperature. 3) Barbecue heats unevenly. (1) 4) One or more of the burners do not ignite. DANGER Failure to correct the above mentioned symptoms may result in a fire, which can cause serious bodily injury or death, and cause damage to property. 8) To reinstall the burners, reverse 3) through 7). Replacin
Résumé du contenu de la page N° 13
R E B E W Assembly Instructions Assemble wheel frame Assemble frame You will need: axle rod, two wheel hubcaps, two You will need: left frame, right frame, two 1/2 inch wheels, wheel frame, hammer and a block of wood. bolts, two nylon washers and a 7/16 inch or adjustable Place one end of the axle rod on the block of wood (or wrench. other protected surface). Tap one hubcap onto the end Note - Work on carpeted area (on grass or one of the of the axle rod. Slide one wheel onto the axle, WEBER box
Résumé du contenu de la page N° 14
Continue frame assembly Complete frame assembly You will need: caster frame, wheel frame, four 1/2 inch You will need: partial frame assembly, two frame bolts, four nylon washers and a 7/16 inch or adjustable connectors, four 2 inch bolts, four nylon wrench. washers and a 7/16 inch or adjustable wrench. Place the caster frame onto the tabs of the left frame, Hold one frame connector between the caster frame so that the swing table locking latch(1) is to the rear. and wheel frame. Add the nylon w
Résumé du contenu de la page N° 15
Insert casters Add Wrap-around Frame Panel You will need: frame assembly and two casters. You will need: wrap around frame panel and a wrench. Push the casters firmly into the inserts in the ends of Place wrap-around frame panel in place: the caster frame. 1) The cut-out tabs should fit between the washer and the frame, as shown. 2) The square cut-out holes fit around the white plugs in the frame as shown Tighten Bolts with wrench. Turn the frame over and continue with assembly. (1) (2) B-3
Résumé du contenu de la page N° 16
Add cooking box (assembly) Your Weber Gas Grill manifold assembly, consisting of You will need: frame assembly, cooking box gas manifold, valves, hose, regulator and gas burners (assembly), 2 inch bolt, nylon washer, keps nut, pliers has been factory assembled, pressure and flame and a 7/16 inch or adjustable wrench. tested. As a safety precaution, we recommend you Uncoil the hose. check the burner alignment: Place the cooking box (assembly) in the frame 1) Are the ends of the burners under the
Résumé du contenu de la page N° 17
Install manifold brackets Install cylinder panel The manifold brackets(2) are already in place on the You will need: Cylinder panel, two 1 3/4inch bolts, two manifold between the valves. nylon cylinder glides, two nylon washers a 7/16 inch or Place your hand underneath the manifold. Lift the adjustable wrench and pliers. manifold and cooking box slightly and hook the Insert the cylinder panel tabs(1) into the slots in the manifold bracket(2) onto the frame brace(1). frame brace(2). (2) (1) (1)
Résumé du contenu de la page N° 18
Add fuel gauge Install igniter You will need: fuel gauge, two wing nuts and two nylon Note - The igniter wires are already attached to the washers. Gas Catcher Ignition Chamber and the igniter. This 1) Slip the bolts on the back of the fuel gauge was done to factory test the ignition system. through the two small holes in the cylinder panel. The igniter lock nut is on the igniter. 2) Add washers to the bolts, then wing nuts, and 1) Loosen the igniter lock nut. tighten with your fingers. 2) Inser
Résumé du contenu de la page N° 19
Fill liquid propane cylinder Check that all burner valves are off Note - The liquid propane cylinder manufacturer is You will need: burner control knobs. responsible for the materials, workmanship and Valves are shipped in the OFF position, but you should performance of the cylinder. If the cylinder has a check to be sure that they are turned OFF. Put the defect, malfunctions, or you have a question regarding knob on each valve. Check by pushing down and the cylinder, call the cylinder manufactu
Résumé du contenu de la page N° 20
One series of tanks mount with the valve facing front. Check for gas leaks The other tanks mount with the valve facing away from DANGER the fuel scale. These types of tanks are illustrated Do not use an open flame to check for gas below. leaks. Be sure there are no sparks or open Hook the liquid propane cylinder onto the fuel gauge. flames in the area while you check for Loosen the cylinder lock wing nut. Swing the cylinder lock down. Tighten the wing nut. leaks. Sparks or open flames will re
