Résumé du contenu de la page N° 1
Any Surface
24 inches
(61 cm)
24 inches
(61 cm)
Any Surface
®
SUMMIT
PLATINUM D4 , D6
BUILT-IN LP GAS GRILL INSTALLATION GUIDE
THIS GAS APPLIANCE IS DESIGNED
FOR OUTDOOR USE ONLY.
42369
LOCATING YOUR GRILL
®
When determining a suitable location for your Summit gas grill installation, give attention to concerns such as exposure to wind, proximity to traffi c paths, and
®
keeping any gas supply lines as short as possible. Never locate the Summit gas grill in a garage, breezeway, shed, under an
Résumé du contenu de la page N° 2
2 BUILT-IN CUTOUT DIMENSIONS GENERAL CONSTRUCTION DETAILS ® Summit Built-In unit and all other accessory units should be on site before construction begins. 1 All dimensions have a tolerance of plus or minus (+/-) / inch (.635 mm). 4 The grill frame rests directly on the Island Structure top fi nished surface. Make sure this surface is level. Do not support the grill from the bottom. If the supporting structure is going to have an electrical outlet for a rotisserie, it should be on the left s
Résumé du contenu de la page N° 3
3 PARTS LIST D4 Left Door - 1 Lid - 1 Cookbox - 1 Right Door - 1 Warming Rack - 1 OR ™ Warm-Up Rack - 1 D6 Lid - 1 Right Enclosure Panel - 1 Cookbox - 1 Front Frame Rail - 1 Left Enclosure Panel - 1 Rear Frame Rail - 1 Front Vent Panel - 1 Rear Panel Assembly - 1 Rear Vent - 1 Bottom Shelf - 1
Résumé du contenu de la page N° 4
4 PARTS LIST ® Flavorizer Bars - 2 Sets Wrench - 1 x10 Sheet Metal Screws - 3 Stainless Steel Plastic Anchors - 3 Cooking Grates 1/2 inch Bolts - 2 4B (1/4 x 20 x 1/2 inch Bolt) - 8 - 3 6B #10-32 x 1/4 inch Steel Screws - 5 Bottom Tray - 1 Nylon Washer - 8 Catch-Pan Holder - 1 Handle - 2 Handle Hardware - 4 Catch-Pan - 1 Rotisserie - 1 Disposable Drip Pans - 2 Rotisserie Motor - 1 Hinge Pin- 2 Hair Pin Cotter- 2 Rotisserie Bracket - 1 Corrugated gas line - 1 Keps Nuts (1/4 x 20 Blk Zinc) -
Résumé du contenu de la page N° 5
5 EXPLODED VIEW - PLATINUM D4 ® 7740501 - Summit Platinum D4 LP Built-In 092005 1 2 3 38 39 4 40 5 41 42 6 43 7 44 45 8 46 9 47 10 48 11 49 50 51 12 52 13 53 14 54 15 55 16 56 17 18 57 19 58 20 21 59 22 23 24 60 25 26 27 61 62 63 64 65 28 66 29 67 30 68 31 32 69 70 33 71 34 72 35 73 74 36 75 37 76
Résumé du contenu de la page N° 6
6 EXPLODED VIEW - PLATINUM D6 ® 7790501 - Summit Platinum D6 LP Built-In 092005 1 2 3 42 4 5 43 6 7 44 45 46 8 47 48 9 49 50 10 51 11 52 12 13 53 54 55 14 56 15 16 57 17 58 18 19 59 20 60 21 22 61 23 24 25 26 62 27 28 63 29 30 64 65 66 67 68 31 69 32 70 33 71 34 35 36 72 73 37 74 38 75 39 76 40 77 41 78
Résumé du contenu de la page N° 7
7 EXPLODED VIEW LIST - PLATINUM D4 1. Hinge Pin 26. Control Panel 52. Rotisserie Fork Screw 2. Thermometer Hardware 27. Front Panel 53. Rotisserie Fork 3. Thermometer Bezel 28. Vent Cover Assembly 54. Rotisserie Shaft ™ 4. Warm-Up Basket 29. Front Frame Rail 55. Cookbox Assembly 5. Smoker Assembly 30. Left Rear Panel 56. Electrode Assembly (16 1/4 inch wire) ® 6. Flavorizer Bar Assembly w/ Smoker 31. Left Panel 57. Right Burner Tube 7. Smoker Box Chip Grate 32. Handle Assembly 58. Heat Shield 8
Résumé du contenu de la page N° 8
8 ASSEMBLY 2 1 1 2 1 Arrow stickers on Frame Rail (1) and Left Side Panel (2) should point toward each other (shown above). Door Stop Bracket (3) should be positioned as 3 shown (left). 2 ATTENTION! Do not fully tighten screws. Clips should slide freely when installed.
Résumé du contenu de la page N° 9
9 ASSEMBLY 3 4
Résumé du contenu de la page N° 10
10 ASSEMBLY 5
Résumé du contenu de la page N° 11
24 inches 24 inches (610mm) (610mm) 11 ASSEMBLY ® CAUTION: Use two people to lift and install the Summit Built-In frame assembly. a.) Lift the frame assembly into the “island” structure opening. Make sure the frame is resting level on the fi nished surface of the structure. 6 b.) Adjust the Front Vent to rest squarely on ground. c.) Apply a bead of silicone sealant (1) around the perimeter and front edges of the grill that are in contact with the “island” structure. This will prevent moistur
Résumé du contenu de la page N° 12
12 ASSEMBLY 7 D4 D6 (1) (2) (3)
Résumé du contenu de la page N° 13
13 ASSEMBLY 8 D4 D6 (1) (2)
Résumé du contenu de la page N° 14
14 ASSEMBLY D4 D6 9 a b Match Holder c
Résumé du contenu de la page N° 15
15 ASSEMBLY 10 1/4" Drill Bit 11
Résumé du contenu de la page N° 16
16 ASSEMBLY 12 13 14 15
Résumé du contenu de la page N° 17
17 GAS SUPPLY BUILT-IN GAS LINE LOCATIONS TYPICAL BULK PROPANE GAS SUPPLY INSTALLATION Note: Leave an access in the “island” structure for gas supply and regulator We recommend that this installation be done by a LICENSED professional. ® service that is not inside the grill structure. Weber has a gas line and General Specifi cations for Piping regulator access door (part # 36311) available from your dealer or call Note - Contact your local municipality for building codes regulating outdoor Custo
Résumé du contenu de la page N° 18
18 GAS SUPPLY GAS LINE PIPING TYPICAL 20 LP PROPANE GAS SUPPLY INSTALLATION Refer to the piping chart at the bottom of previous page. ® We strongly recommend that you use the Summit Built-In The corrugated gas line from the manifold is 58 inches long. Do not Tank Cabinet (#21280) for installations using a 20 lb LP cylinder, mounted extend the gas line. remotely in an “island” structure. We have provided the means to make an SAE 45° fl are connection. Do ® The Summit Built-In Tank Cabinet
Résumé du contenu de la page N° 19
19 GAS SUPPLY c). If the remote LP cylinder enclosure has four sides, a top and a bottom, DANGER and is intended for installation in a built-in “island” enclosure; 1). At least one ventilation opening (a hole or group of holes, for the Use of any other hose and regulator assembly could be purpose of ventilation) needs to be on one side of the enclosure dangerous, and may not provide adequate gas supply that communicates with the outside of the “island” structure. If a gas ® to the Summit
Résumé du contenu de la page N° 20
20 GAS SUPPLY VENTILATION CONNECT GAS SUPPLY A 58 inch corrugated gas line is supplied with the grill. This line needs to WARNING: Air holes must be provided in the structure pass through the gas inlet opening to the main gas supply. at the top and bottom to provide ventilation in the event of 1) Connect the corrugated gas line to the manifold located on the right a gas leak. hand side of grill under the control panel. Use the 1/2” fl ared gasket (1) to ensure proper seal. Air holes can be