Résumé du contenu de la page N° 1
by
Bushman
LP Gas Grill
Assembly and Use Manual for:
Bushman Deluxe
Bushman Deluxe
For use with models:
7710.8.641
7710S8.641
FOR OUTDOOR HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE.
For Customer Service, call 1-800-251-7558 or visit our web site at www.aussiegrills.com
• Failure to follow these instructions could result in fire or explosion which could cause death,
serious personal injury, or property damage.
• Read and follow instructions carefully before assembly or use.
• Do not use th
Résumé du contenu de la page N° 2
I. IMPORTANT SAFEGUARDS...........................................2 2) Precautions............................................................16 3) Leak Testing............................................................17 II. Assembly Instructions.........................................................5 C) Operating the LP Gas Grill........................................17 Step 1 - Assemble Wheel Leg...........................................5 1) Preparation Before Cooking.................
Résumé du contenu de la page N° 3
18. DANGER! If you see, smell, or hear the hiss of 7. WARNING! If your grill catches on fire: escaping gas from the LP cylinder: • If the fire is in the grill portion and you can safely A. Get away from the cylinder. reach the control knobs, then turn them off by turning B. Do not attempt to correct the problem yourself. knobs clockwise. If you cannot safely reach the C. Call your local fire department. control knobs, call the fire department. • If the fire involves one of the hoses, and you
Résumé du contenu de la page N° 4
30. Use of this LP gas grill other than for the intended use, 37. Never store an LP gas cylinder indoors (empty or filled). or alteration of LP gas grill in any way may not be safe If storing the gas grill indoors, disconnect LP gas cylinder and will void any warranty. and store it outdoors out of the reach of children. 31. Never attempt to repair the LP gas grill or cylinder 38. Never leave an LP cylinder inside a vehicle which may yourself. Contact the manufacturer for information become ove
Résumé du contenu de la page N° 5
Step 1 - Assemble Wheel Leg Tools: •Assemble Cylinder Slide Bracket to left leg using 4 M6 x 15mm Screws. •Assemble the Cylinder Slide Lock to the Cylinder Slide Bracket using 2 Wing Bolts. Notice orient holes closer to this edge. Cylinder Screw Wing Bolt Slide Lock M6 x 15mm M6 Cylinder Slide 2 pcs 4 pcs Bracket Threaded holes Left Orient Leg. Right Notice two holes to the front. •Assemble wheels and cylinder support to wheel leg using 2 axle pins and 2 cotter pins. Orient Cylinder Support wit
Résumé du contenu de la page N° 6
STEP 3 - Assemble Cart Screw Screw Nut M6 x 35mm M6 x 50mm M6 4 pcs 4 pcs 4 pcs •Assemble Rear Brace to wheel leg and fixed leg using 4 M6 x 35mm Screws and 4 M6 Nuts. •Assemble the 2 Cart Braces to the wheel leg and fixed leg using 4 M6 x 50 mm Screws. Rear Brace Cart Brace 6
Résumé du contenu de la page N° 7
STEP 4 - Attach Flavor Activator Pins, Grease Cup Hanger, Burner & Heat Shield Follow the steps in order below. Refer to the step numbers below and beside the images. 1. Assemble 2 flavor activator Mounting Studs and two Fiber Washers to the bowl using 2 M6 nuts. 2. Insert Grease Cup Hanger into bowl. 3. Insert Burner Venturi tubes down through holes in bottom of grill bowl toward front of grill. Also insert igniter wire through hole in bottom of bowl. From underside of bowl, insert 2 ST 4
Résumé du contenu de la page N° 8
STEP 5 - Attach Bowl to Cart Screw M6 x 45mm 4 pcs Heat Shield Fiber Washer 4 pcs Cylinder Slide Bracket Bowl Spacer 4 pcs Fiber Washer Nut M6 4 pcs Bowl Spacer Screw M4 x 10mm 2 pcs Wing Nut M4 2 pcs •Assemble bowl to cart using 4 M6 x 45mm Screws, 4 Fiber Washers, 4 Spacers, and 4 M6 Nuts. •Make sure heat shield is resting on top of cylinder slide bracket. •Secure heat shield to cylinder slide bracket using 2 M4 x 10mm Screws and Wing Nuts. 8
Résumé du contenu de la page N° 9
STEP6 - Attach Control Panel Screw Nut M6 x 50mm M6 4 pcs 4 pcs •Insert valve tips on back of control panel into burner venturi. Secure control panel to cart using 4 M6 x 50mm Screws and 4 M6 Nuts. Valve Valve Confirm the valve is inserted into the burner venturi. Venturi STEP 7 - Attach Igniter Wire •Attach Igniter Wire : Push electrode connector at end of Igniter wire onto center tab on rear of Igniter Button. •NOTE: Be sure to route electrode wire away from hot areas of the grill. 9
Résumé du contenu de la page N° 10
STEP - 8 Mounting Hood/ Bowl Hinges Hood Hinge Bolt Hood 2 pcs M6 X 15 8 pcs Fiber Washer 8 pcs Bowl Hinge Washer Nut M6 M6 2 pcs 8 pcs 8 pcs •Insert M6 x 15mm Bolt through Hood Hinge and Fiber Washer and into hole in back side of Grill Hood as shown. Install M6 Washer and secure with M6 Nut. (See Photos 1 & 2 below) Repeat for remaining holes to secure two Hood Hinges. •Insert M6 x 15mm Bolt through Bowl Hinge and Fiber Washer and into hole in back side of Grill Bowl as shown. Install M6 Was
Résumé du contenu de la page N° 11
STEP 9 - Attach Hood Cotter Pin Hinge Pin 2 pcs 2 pcs •Align Hood Hinge tabs with Bottom Hinge tabs and insert Hinge Pins from outside. Secure each Hinge Pin with Cotter Pin as shown. •Close Hood and check assembly to make sure that the hood and bowl fit properly together. Adjust hood by loosening the Hinge Bolts and retightening. 11
Résumé du contenu de la page N° 12
To reduce the risk of a laceration hazard, wear protective gloves when handling parts that have sharp edges. STEP 10 - Attach Hood Handle & Handle Shield Hood Handle 1 pc Bolt Hood M5 X 10 Shield 2 pcs 1Pc •Insert M5 x 10mm Bolt through Handle Shield, then through inside of Hood into Hood Handle. Repeat for other side of handle. NOTE: DO NOT Overtighten mounting screws. You could crack the porcelain grill coating. Step 11 - Insert Flavor Activator Note: Place protrusions toward hood. •Place Fl
Résumé du contenu de la page N° 13
Screw STEP 14 - Assemble Side Tables Table M6 x 45mm Spacer •Slide 8 side table spacers onto 8 8 pcs 8 pcs M6 x 45 mm screws. Nut M6 •Insert M6 x 45mm screws and 8 pcs side table spacers through bottom holes of side table and through leg. Secure with M6 nuts and tighten. •Insert M6 x 45mm screws and side table spacers through top holes of leg. Secure with M6 nut and tighten. •Repeat for other side table. Note: The side table folds for storage. Make sure side table is secure when locked in
Résumé du contenu de la page N° 14
STEP 16 - Insert Drip Cup •Insert drip cup into hanger clip underneath grill bowl. Drip Cup Step 17 - Attach LP Cylinder Note: Turn all control knobs and LP cylinder valve to the “Off” position. 2. Place cylinder on cylinder 3. Lower the cylinder slide support and hold in place. lock onto collar of cylinder Orient cylinder with open and tighten wing bolts. side of collar under the grill as shown. Notice not all cylinders look alike. 1. Loosen wing bolts on cylinder slide lock. Raise to highest
Résumé du contenu de la page N° 15
OPERATING AND MAINTAINING YOUR GAS GRILL · If you obtain LP gas through a cylinder exchange dealer, GAS, CYLINDER, HOSE AND make sure you are getting a safe and adequate O.P.D. REGULATOR INFORMATION cylinder. Use only a licensed LP gas cylinder dealer. This LP gas grill was designed to use propane gas. Propane · Keep children away from LP gas cylinder at all times. cylinders will supply gas all year round, even on cold winter days. · Do not use, store, or transport the LP gas cylinder where
Résumé du contenu de la page N° 16
· Never connect or disconnect LP gas cylinder or fittings Precautions while grill is in use or is hot. · When the LP gas cylinder is connected, the grill must be kept outside in a well-ventilated space. Turn off all of the grill control knobs and the LP cylinder valve · Carefully read the Important Safeguards section when grill is not in use. of this manual (pages 2 through 4). Make sure · Move gas hose as far away as possible from hot surfaces. you follow and understand all instructions
Résumé du contenu de la page N° 17
9)Check for leaks by brushing the soap solution on all LP gas Leak Testing connections and fittings (such as those shown by the heavy arrows in the diagram below.) Make sure you generously brush the locations with the soap solution, completely · Always perform a leak test before each use. surrounding the connections and fittings. · Leak test must be performed in a well ventilated 10)If “growing” bubbles appear on any of the connection points, area. then you have detected a gas leak. Immed
Résumé du contenu de la page N° 18
· Always inspect the gas hose and regulator assembly WARNING: Continued before each use. If the hose is cut, damaged, or shows · Never touch hot surfaces. Use heat resistant signs of excessive abrasion or wear, do not use the LP gloves, long-handled tongs, or cooking mitts at all gas grill. Contact the manufacturer, as the hose and times since the grill will become very hot. Open regulator assembly must be replaced with an assembly the hood carefully when cooking to avoid from the s
Résumé du contenu de la page N° 19
Manual Lighting of the Grill 4) Push in and turn the right main burner control knob counter- clockwise to the “high” position. WARNING: If the burner fails to ignite after · Open Hood before lighting the grill to prevent an following the above procedure, turn control knob to explosion from gas build-up. the off position and close the valve on the LP cylinder. · Always inspect the gas hose and regulator Wait five minutes and repeat all of the above manual assembly before each use. If th
Résumé du contenu de la page N° 20
Check Your Flame End of Cooking Session Your burner has been preset by the manufacturer for opti- mal flame performance. A blue flame, possibly with a small yellow tip, is the result of the optimal air and LP gas mix- · Never leave your LP gas grill unattended during use ture. (See diagram below) or cleaning. After each cooking session, close the hood and turn the grill burners to the “high” position and burn for five minutes. Yellow Tip This procedure will burn off cooking residue, thus making
