Résumé du contenu de la page N° 1
Use & Care Guide
Manual de Uso y Cuidado
English / Español
Models/Modelos: 148.16154210
Item / Artículo: 640-03838917-7
Kenmore®
Liquid Propane Gas Grill
Parilla a gas de propane liquido
P/N 2818-2T-Manual
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
www.kmart.com
TM
Résumé du contenu de la page N° 2
If you smell gas: For residential use only. Do not use for commercial cooking. 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. Open lid. Installation Safety Precautions 4. If odor continues, keep away from the • Use grill, as purchased, only with LP (propane) gas and the appliance and immediately call your gas regulator/valve assembly supplied. A conversion kit must be purchased for use with natural gas. supplier or your fire departm
Résumé du contenu de la page N° 3
TABLE OF CONTENTS For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in ® the U.S.A. call 1-800-4-MY-HOME For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 2 Grill Service Center. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 WARRANTY Product Record Information . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Symbols. . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 4
USE AND CARE LP Cylinder • The LP cylinder used with your grill must meet the following requirements: ` • Use LP cylinders only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. • NEVER store a spare LP cylinder under or near • LP cylinders must be constructed and marked in accordance the grill appliance or in an enclosed area. with specifications for LP cylinders of the U.S. Department of Transportat
Résumé du contenu de la page N° 5
LP Tank Exchange Connecting Regulator To The LP Tank •Many retailers that sell grills offer you the option of replacing 1. LP tank must be properly secured onto grill. (Refer to your empty LP tank through an exchange service. Use only assembly section.) those reputable exchange companies that inspect, precision 2. Turn all control knobs to the OFF position. fill, test and certify their cylinders. Exchange your tank only 3. Turn LP tank OFF by turning OPD hand wheel clockwise to for an OPD
Résumé du contenu de la page N° 6
Leak Testing Valves, Hose and Regulator 1. Turn all grill control knobs to OFF. 2. Be sure regulator is tightly connected to LP tank. 3. Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off Hold coupling nut and regulator immediately. There is a major leak at the connection. as shown for proper connection Correct before proceeding by calling Sears for to LP tank valve. ® replacement parts at 1-800-4-MY-
Résumé du contenu de la page N° 7
Safety Tips Before opening LP cylinder valve, check the coupling nut for tightness. When grill is not in use, turn off all control knobs and LP For Safe Use of Your Grill and to Avoid Serious cylinder valve. Injury: Never move grill while in operation or still hot. • Do not let children operate or play near grill. Use long-handled barbecue utensils and oven mitts to • Keep grill area clear and free from materials that avoid burns and splatters. Maximum load for
Résumé du contenu de la page N° 8
5. If ignition does not occur in 5 seconds, turn the burner Burner Flame Check control off, wait 5 minutes for gas to clear away, and repeat •Remove cooking grates and heat diffusers. Light burners, the lighting procedure. rotate knobs from HIGH to LOW. You should see a smaller 6. To light other burners, repeat step 4. flame in LOW position than seen on HIGH. Perform burner NOTE: If ignitor does not work, follow Match Lighting flame check on sideburner, also. Always check flame prior
Résumé du contenu de la page N° 9
•Stainless steel surfaces: To maintain your grill’s high quality Cleaning the Burner Assembly appearance, wash with mild detergent and warm soapy water Follow these instructions to clean and/or replace parts of and wipe dry with a soft cloth after each use. Baked-on burner assembly or if you have trouble igniting grill. grease deposits may require the use of an abrasive plastic 1. Turn gas off at control knobs and LP cylinder. cleaning pad. Use only in direction of brushed finish to av
Résumé du contenu de la page N° 10
Indirect Cooking thermometer to ensure proper internal food temperatures. Poultry and large cuts of meat cook slowly to perfection on the Chill: Refrigerate prepared foods and leftovers promptly. grill by indirect heat. Place food over unlit burner(s); the heat For more information call: USDA Meat and Poultry Hotline from lit burners circulates gently throughout the grill, cooking at 1-800-535-4555 (In Washington, DC (202) 720-3333, 10:00 meat or poultry without the touch of a direct flame
Résumé du contenu de la page N° 11
Natural Gas Conversion Kit Natural Gas Connection Preparation: To purchase a Natural Gas Conversion Kit call Sears at 1. Turn off gas supply, and then remove cap on gas R ○ 1-800-4-MY-HOME supply side. 2. Recommended: Install a shut-off valve on gas supply side before installing the socket. Natural gas conversion kit 3. Socket should be installed by an authorized Kenmore Model # 10478 technician in accordance with the national fuel gas (Manufacturer Part No.: 28
Résumé du contenu de la page N° 12
Natural Gas Always protect your hand with a pot holder or cooking If your grill is for Natural Gas, it is set for a 7-in. water glove when coming into contact with a hot surface. column (WC) and is for use with Natural Gas only. Gas pressure is affected by gas line size and the length of Hood up when grilling meats, especially chicken. Hood gas line run from house gas line. Follow the down when indirect or rotisserie cooking. recommendations in the chart below. NEVER leave you
Résumé du contenu de la page N° 13
PARTS LIST Manufacturer Manufacturer Key Qty Description Key Qty Description Part # Part # 1 1 HOOD HANDLE 2818-2T-6200 31 1 RIGHT ANGLE BRACKET 2818-2T-1700 2 2 HANDLE BASE RB2818C-00-4001 32 2 CASTER,LOCKING 2518-3-8007 3 2 SCREW 1/4-20×5/8 in. 33 2 CASTER 2518-3-8008 4 4 RUBBER GASKET 3219-8082 34 1 WING-HEAD SCREW 1/4-20UNC×2 in. 5 1 HOOD 2818-2T-6000 35 1 SCREW W/SHOULDER 5/32-32×3/8 in. 36 1 MATCH HOLDER 3019L-1710 6 2 SCREW 5/16-18×3/4 in. 37 1 DOOR(R) 2818-2T-8000 7
Résumé du contenu de la page N° 14
PARTS DIAGRAM 15-1 15-2 15-3 15-4 7 8 9 10 11 12 13 14 6 16 5 4 3 17 2 18 19 1 18 20 55 21 54 53 22 40 52 51 23 50 24 25 49 26 48 27 47 46 28 45 29 44 43 42 41 30 40 39 31 38 37 36 35 34 33 32 14
Résumé du contenu de la page N° 15
UNPACKING After removing all parts and hardware pack from the top of the shipping box, and when the only part showing is the grill head, use a box cutting knife to slice down the sides of the box. Be careful of staples along shipping box edges. Remove the corner supports from the box and the styrofoam side pieces from the grill head. Allow grill head to rest on cardboard until placing grill head on cart in Step 7. Open grill lid and remove all packaged parts and packing material. WAR
Résumé du contenu de la page N° 16
Loosen the 4 screws at the corners of the bottom panel 3 to 4 turns. Place the holes in the base of each side panel over the loosened screws and slide the panel to the front until it stops. Retighten the screws. Use six 3/16-24 x3/8 in. screws to fasten the rear panel to side panels. Left Panel Rear Panel 3/16-24 x 3/8 in. Screw Qty. 6 Right Panel Bottom Panel Remove the cap and nut from the electrical igniter. Use the nut to assemble the ig
Résumé du contenu de la page N° 17
Loosen the two screws in the right and left angle brackets 3 to 4 turns. Insert the screws through the 2 holes at the base of each side panel and slide the bracket down until it stops. Attach each bracket to the bottom panel with one 3/16-24 x 3/8 in. screw. Retighten the 4 loosened screws. 3/16-24 x 3/8 in. Screw Qty. 2 Attach the beam to side panels with four 3/16-24 x 3/8 in. screws as shown. Left Panel Rear Panel 3/16-24 x 3/8 in. Scre
Résumé du contenu de la page N° 18
Attach the drip tray support to the beam and rear panel with four 3/16-24 x 3/8 in. screws as shown. Note: Tabs at front attach beneath beam upper ledge. Drip tray support Left Panel 3/16-24 x 3/8 in. Screw Rear Panel Qty. 4 Right Panel Beam Grill Head Assembly First, lock the two rear casters of the grill cart. Locate the gas pressure regulator and igniter wires under the grill head control panel. Carefully cut the tie wrap(s) from the regu
Résumé du contenu de la page N° 19
Connect the four burner ignition wires to the four sockets on the right side of the igniter. Connect the remaining wire to the remaining open socket. Place the ground wire through the slots on the side panel as shown below. Loosen one control panel screw, install the ground wire onto the screw, and retighten it to make a good connection. Ground Wire Ground Wire Install the doors For each door, insert the bottom hinge pin into the hole in the bottom panel.
Résumé du contenu de la page N° 20
Install two wing mechanisms to each wing table with four screws as shown. 3/16-24 x 5/8 in. Screw Qty. 8 Install Wing Tables Loosen the 2 screws (as shown) on each side of grill head 4 to 6 turns. Slide the slot in each wing mechanism bracket over a loosened screw. Insert one 1/4-20 x 3/4 in. screw through hole in each wing mechanism bracket and tighten to grill head. Note: Attach each wing table so that rounded edge faces front. Raise each table until it
