Résumé du contenu de la page N° 1
Use & Care Guide
Manual de Uso y Cuidado
English / Español
Models/Modelos: 146.16132110/146.16133110
Kenmore®
Liquid Propane Gas Grill
Parilla a gas de propane liquido
P/N 40200104
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
™
Résumé du contenu de la page N° 2
Installation Safety Precautions • Please read this User’s Manual in its entirety before using DANGER the grill. • Failure to follow the provided instruction can result in If you smell gas: seriously bodily injury and/or property damage. • Some parts of this grill may have sharp edges. Please wear suitable protective gloves. 1. Shut off gas to the appliance. • Use grill, as purchased, only with LP (propane) gas and the 2. Extinguish any open flame. regulator/valve assembly su
Résumé du contenu de la page N° 3
TABLE OF CONTENTS WARRANTY . . 2 For Your Safety . . . KENMORE GRILL WARRANTY . . 2 Grill Service Center. . . One Year Full Warranty on Kenmore Grill . 2 Product Record Information . . . . . 2 If this grill fails due to a defect in material or workmanship Installation Safety Precautions . . . within one year from the date of purchase, call 1-800-4-MY . . 2 Safety Symbols . . . ® HOME to arrange for free repair (or replacement if repair . 3 proves impossible). Kenmore Grill
Résumé du contenu de la page N° 4
LP Cylinder USE AND CARE • The LP cylinder used with your grill must meet the following requirements: • Use LP cylinders only with these required measurements: 12" DANGER (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) Capacity maximum. • NEVER store a spare LP cylinder under or near the • LP cylinders must be constructed and marked in accordance appliance or in an enclosed area. with specifications for LP cylinders of the U.S. Department of Transportation (DOT) or
Résumé du contenu de la page N° 5
LP Tank Exchange Connecting Regulator To The LP Tank • Many retailers that sell grills offer you the option of replacing 1. LP tank must be properly secured onto grill. (Refer to your empty LP tank through an exchange service. Use only those assembly section.) reputable exchange companies that inspect, precision fill, test 2. Turn all control knobs to the OFF position. and certify their cylinders. Exchange your tank only for an OPD 3. Turn LP tank OFF by turning OPD hand wheel clockwi
Résumé du contenu de la page N° 6
Leak Testing Valves, Hose and Regulator 1.Turn all grill control knobs to OFF. 2.Be sure regulator is tightly connected to LP tank. 3.Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding by calling Sears for replacement parts at ® 1-800-4-MY-HOME . Hold coupling nut and regulator 4.Brush soapy solution onto areas where bubbles are shown in
Résumé du contenu de la page N° 7
Safety Tips ▲ Before opening LP cylinder valve, check the coupling nut for WARNING tightness. ▲ When grill is not in use, turn off all control knobs and LP cylinder For Safe Use of Your Grill and to Avoid Serious valve. Injury: ▲ Never move grill while in operation or still hot. • Do not let children operate or play near grill. ▲ Use long-handled barbecue utensils and oven mitts to avoid burns • Keep grill area clear and free from materials that and splatters. burn. ▲ Maximu
Résumé du contenu de la page N° 8
Burner Flame Check • Remove cooking grates and flame tamers. Light burners, rotate WARNING knobs from HIGH to LOW. You should see a smaller flame in LOW position than seen on HIGH. Perform burner flame check Turn controls and gas source or tank OFF when not on sideburner, also. Always check flame prior to each use. If in use. only low flame is seen refer to "Sudden drop or low flame" in the Troubleshooting Section. HIGH CAUTION LOW If ignition does NOT occur in 5 seconds, turn t
Résumé du contenu de la page N° 9
Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burner W CAUTION ARNING assembly or if you have trouble igniting grill. 1. Turn gas off at control knobs and LP cylinder 2. Remove cooking grates and heat diffusers. SPIDER ALERT! SPIDER ALERT! 3. Remove screws and carryover tubes from rear of burners. SPIDER ALERT! 4. Remove screw and washers to disengage burner from IMPORTANT: Always ensure that the venturi burner tubes bracket on fir
Résumé du contenu de la page N° 10
Indirect Cooking Food Safety Poultry and large cuts of meat cook slowly to perfection on the grill Food safety is a very important part of enjoying the outdoor by indirect heat. Place food over unlit burner(s); the heat from lit cooking experience. To keep food safe from harmful bacteria, burners circulates gently throughout the grill, cooking meat or follow these four basic steps: poultry without the touch of a direct flame. This method greatly Clean: Wash hands, utensils, and sur
Résumé du contenu de la page N° 11
PARTS LIST Key Description Qty Part Number Key Description Qty Part Number Key Qty Description 1 Sideburner Lid 1 40200044 36 Mater Holder Bracket 1 40800129 HEAT DIFFUSERS 1 2 42 3 2 Rotate Rod, Sideburner Lid 2 40800118 37 Back Panel 1 40200052 COOKING GRATE 1 2 43 3 3 Sideburner Grid 1 40800119 38 Door Bracket 1 40200055 SWING AWAY GRATE 3 1 44 1 4 Sideburner 1 40800120 39 Right Door Pin Bracket 1 40200057 4 1 45 1 CLIP, F/ GREASE CUP 5 Ignitor Wire, Sideburner 1 40800121 4
Résumé du contenu de la page N° 12
PARTS DIAGRAM 43 43 43 44 35 42 14 42 42 12 15 24 24 17 13 37 22 22 22 23 38 16 20 39 41 31 40 21 25 34 26 30 32 29 27 33 28 36 9 29 45 11 2 1 46 3 47 10 8 6 7 12 • 16132-4200104
Résumé du contenu de la page N° 13
BEFORE ASSEMBLY READ AND FOLLOW THE INSTRUCTIONS BELOW TO CORRECTLY UNPACK GRILL PARTS FROM SHIPPING BOX. Step 1: Once you open the top of the shipping box, slice down its four edges with a box cutter. Take out the Hardware Pack, two grill side panels, back panel and bottom shelf. Next remove the door bracket, back rail and warming rack. Take the left and right doors out of protective styrofoam, but leave grill head in styrofoam until Step 2. Remove all parts from plastic bags. 16
Résumé du contenu de la page N° 14
BEFORE ASSEMBLY Step 2: With the aid of an assistant, turn grill head over on its side as shown in the first figure below, and remove the top styrofoam piece. Lay the styrofoam piece flat on the floor. With the aid of an assistant, lift the grill head out of the bottom styrofoam piece. Place the grill upright on the other styrofoam piece as shown in the second figure below. CAUTION: DO NOT place the grill head directly on the floor or the grease
Résumé du contenu de la page N° 15
BEFORE ASSEMBLY Step 3: Open grill lid, and take out the small boxes packed within the grill head. Remove all packing materials, and remove all parts from boxes as shown in the figures below. 16132-40200104 • 15
Résumé du contenu de la page N° 16
ASSEMBLY CAREFULLY READ AND PERFORM ALL ASSEMBLY INSTRUCTIONS ON THE FOLLOWING PAGES. Tools Required: Adjustable wrench (not provided) Screwdriver (not provided) 7/16” Combination wrench (not provided) The following hardware is provided in a blister pack for convenient use. M4X10 screw Qty: 20 pcs M5X10 screw M5 flat washer M5 lock washer Qty: 4 pcs Qty: 4 pcs Qty: 4 pcs M6X13 screw M6X15 screw M6 flat washer(Dia 16) Qty: 16 pcs Qty: 16 pcs Qty: 8 pcs M6 flat washer(Dia 1
Résumé du contenu de la page N° 17
Bottom Shelf □ Turn bottom shelf upside down. Attach the wheels to bottom shelf with (16) M6x15 screws, M6 lock washers and M6 flat washers(Dia 12). Note: The casters with brakes should be mounted 2 1 on the side with cutout holes. □ Turn bottom shelf right side up. Attach door magnets to bottom shelf with (2) M4x10 screws. M6X15 screw Qty: 16 pcs M6 lock washer Qty: 16 pcs M6 flat washer(Dia 12)Qty: 16pcs
Résumé du contenu de la page N° 18
Cart □ To attach side panels, align side panel leg holes with leg holes on each side of bottom shelf. Left side panel has match holder attachment. □ Attach left and right side panels to sides of bottom shelf with (4) M6x13 screws, M6 lock washers and M6 flat washers(Dia 16). (A) □ Attach back panel to bottom shelf and two side panels with (6) M4x10 screws. (B) □ Attach tank baffle bar to back panel and bottom shelf with (2) M4x10 screws. (C) □ Align door bracket holes with holes on side
Résumé du contenu de la page N° 19
Front Doors □ Remove the (4) M4x10 screws pre-assembled to the door handle ends, and use them to attach handles to doors. □ Insert the lower door pin into the hole on the bottom shelf. Push down the upper door pin, align it beneath hole in door pin bracket, and release pin so that it inserts in hole. □ Repeat this for the other door. □ Note: If the doors do not line up when closed or cannot close freely, loosen the screws on the door pin bracket. Adjust the door pin bracket as necessa
Résumé du contenu de la page N° 20
Grill Head to Cart □ This step requires two people to lift and position grill head onto cart. □ Remove the tie wraps securing regulator hose to underside of grill head. Pull hose and igniter wires out to side of grill head. □ Carefully lower the grill head onto the cart. Make sure the regulator hose and igniter wires are hanging outside the cart. Open lid and attach head to cart with (4) M6x13 screws and M6 compression washers. M6X13 screw Qty: 4 pcs M6 compression washer Qty: 4 pc
