Résumé du contenu de la page N° 1
HOME CINEMA CONTROL CENTER
RX-F10S
INSTRUCTIONS
LVT1163-007A
[B]
cover_RX-f10[B]_f.p65 3 04.2.13, 16:42
Résumé du contenu de la page N° 2
Warnings, Cautions and Others IMPORTANT for the U.K. Caution–– STANDBY/ON button! Disconnect the mains plug to shut the power off completely. DO NOT cut off the mains plug from this equipment. If the The STANDBY/ON button in any position does not plug fitted is not suitable for the power points in your home or disconnect the mains line. The power can be remote the cable is too short to reach a power point, then obtain an controlled. appropriate safety approved extension lead or consult your dea
Résumé du contenu de la page N° 3
Caution: Proper Ventilation To avoid risk of electric shock and fire and to protect from damage. Locate the apparatus as follows: Front: No obstructions open spacing. Sides: No obstructions in 10 cm from the sides. Back: No obstructions in 15 cm from the back. Bottom: No obstructions, place on the level surface. In addition, maintain the best possible air circulation as illustrated. Spacing 15 cm or more RX-F10S Front Wall or obstructions Stand height 15 cm or more Floor G-2 safety_RX-F10[B]_f.p
Résumé du contenu de la page N° 4
SAFETY INSTRUCTIONS “SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. Do read the operating instructions before you attempt to use the equipment. Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are pro
Résumé du contenu de la page N° 5
Table of Contents Parts identification ................................................ 2 Getting started ...................................................... 4 Before Installation .................................................................. 4 Checking the supplied accessories ....................................... 4 Putting batteries in the remote control ................................... 4 Connecting the FM and AM (MW) antennas ......................... 5 Connecting the speakers ...
Résumé du contenu de la page N° 6
Remote control See pages in parentheses for details. Parts identification 1 TV DIRECT button (14) 2 Standby/on buttons (12, 14, 36 – 40) AUDIO, DVR/DVD , VCR , STB , TV 3 Source selecting buttons (12, 14, 25, 36, 38, 39) DVR/DVD, VCR, VIDEO, TV, DVD MULTI, FM/AM 4 TV VOL (volume) +/– button (36, 38) 5 CHANNEL +/– button (36 – 40) 6 • Operating buttons for video components (36, 37, 39) 4, 3, ¢, 1, 7, 8, ¡ • Operating buttons for tuner (25, 26) ( TUNING, FM MODE, TUNING 9, MEMORY 7 • Operating b
Résumé du contenu de la page N° 7
See pages in parentheses for details. Front panel 1 2 3 4 5 6 RX-F10 HOME CINEMA CONTROL CENTER SOURCE MASTER SELECTOR VOLUME / MULTI JOG DVD MULTI DVR/DVD VCR VIDEO TV FM/AM STANDBY / ON TV DIRECT SETTING ADJUST SURROUND SET/TUNER PRESET PHONES 7 8 9 p q w 1 STANDBY/ON button and standby lamp (12, 14) 7 TV DIRECT button (14) 2 Display window (see below) 8 SETTING button (18) 3 Source lamps 9 ADJUST button (22) DVD MULTI, DVR/DVD, VCR, VIDEO, TV, FM/AM p SURROUND button (35) 4 • SOURCE SEL
Résumé du contenu de la page N° 8
Putting batteries in the remote control Getting started Before using the remote control, put two supplied batteries first. 12 3 1 Press and slide the battery cover on the back Before Installation of the remote control. 2 Insert batteries. General precautions Make sure to match the polarity: (+) to (+) and (–) to (–). • Be sure your hands are dry. • Turn the power off to all components. 3 Replace the cover. • Read the manuals supplied with the components you are going to connect. If the range or
Résumé du contenu de la page N° 9
Connecting the FM and AM (MW) antennas AM (MW) loop antenna (supplied) If FM reception is poor, connect an outdoor FM antenna (not supplied). Snap the tabs on the loop into the slots of the base to assemble the AM (MW) loop antenna. FM 75 AM LOOP FM antenna (supplied) If AM (MW) reception is poor, COAXIAL AM EXT connect an outdoor single vinyl- ANTENNA covered wire (not supplied). NOTES AM (MW) antenna connection • If the AM (MW) loop antenna wire is covered with Connect the AM (MW) loop anten
Résumé du contenu de la page N° 10
Connecting the speakers Speaker Layout Diagram C Center speaker (C) LR SW CAUTION: SPEAKER IMPEDANCE 6 ~ 16 LS SB RS FRONT CENTER SURROUND SURROUND SPEAKERS BACK RIGHT LEFT RIGHT LEFT SUBWOOFER OUT Powered subwoofer (SW) Right front speaker (R) Left front speaker (L) Surround back speaker (SB) Right surround Left surround speaker (RS) speaker (LS) Connecting the speakers Connecting the powered subwoofer By connecting a subwoofer, you can enhance the bass or Turn off all components before mak
Résumé du contenu de la page N° 11
DO NOT use a TV through a VCR or a TV with a built-in Connecting video components VCR; otherwise, the picture may be distorted. SCART connection You can enjoy pictures and sounds from playback components Turn off all components before making connections. simply by connecting with the SCART cable. • Illustrations of the input/output terminals are typical • If your video components have digital output terminal, also examples. When you connect other components, refer also connect them using the dig
Résumé du contenu de la page N° 12
For TV and video format For T-V LINK This receiver cannot convert the video signals. When the video • You can use the T-V LINK function if you connect a T-V LINK signal of one video component is different from that of the other compatible TV and VCR to this receiver with a fully wired (for example, one is S-video, the other is Composite), you may SCART cables. For details on T-V LINK, refer also to the not see the pictures appropriately. In this case, unify the video manuals supplied with the TV
Résumé du contenu de la page N° 13
When you connect a DVD player with its analogue discrete output jacks (DVD MULTI IN): This connection is the best connection method for enjoying DVD Audio sounds. When a DVD Audio disc is played back, the original high- quality sounds can be reproduced only using this connection. Turn off all components before making connections. Monaural audio cable AUDIO VIDEO VIDEO S-VIDEO COMPONENT Åı (not supplied) DVD player VIDEO IN CENTER DVR/DVD White SUB- IN WOOFER MONITOR OUT DVD MULTI IN ÇÎ Red RIGHT
Résumé du contenu de la page N° 14
7 Connecting another video component to the VIDEO IN jacks If your video components have S-video (Y/C-separation) and/or component video (Y, PB, PR) terminals, connect them using an S-video cable (not supplied) and/or component video cable (not supplied). By using these jacks, you can get better picture quality in the order: Component video > S-video > Composite video To enjoy the playback from the component connected to these jacks, select “VIDEO” as the source (see page 12). Turn off all compo
Résumé du contenu de la page N° 15
Digital connection Connecting the power cord This receiver is equipped with three DIGITAL IN terminals—one digital coaxial terminal and two digital optical terminals. When all the audio/video connections have been made, connect To reproduce the digital sound, use the digital connection in the AC power plug to the wall outlet. Make sure that the plugs are addition to the analogue connection methods described on pages inserted firmly. The standby lamp lights in red. 7 to 10. CAUTIONS: Digital coax
Résumé du contenu de la page N° 16
2 Select the source to play Basic operations On the front panel: Turn SOURCE SELECTOR until the source name you want appears on the display. The source lamp corresponding to the selected source lights in red. • As you turn SOURCE SELECTOR, the source changes as follows: EQ C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE PL LPCM L C R ATT DOLBY D NEO : 6 HP S . WFR LFE DTS AAC DSP 3D MHz LS SB RS 96 / 24 AUTO SR kHz 1 2 3 DVD MULTI DVR/DVD (DGT) VCR (DIGITAL)
Résumé du contenu de la page N° 17
3 Adjust the volume Selecting the digital decode mode If the following symptoms occur while playing Dolby Digital or DTS To increase the volume, turn MASTER VOLUME software with “DGTL AUTO” selected (see page 12), follow the control clockwise (or press VOLUME + on the procedure below: remote control). • Sound does not come out at the beginning of playback. • Noise comes out while searching for or skipping chapters or To decrease the volume, turn MASTER VOLUME tracks. control counterclockwise (or
Résumé du contenu de la page N° 18
Activating TV Direct TV Direct enables you to use this receiver as an AV selector while the receiver is turned off. When TV Direct is activated, the pictures and sounds go from the video components such as DVD player to the TV through this receiver. Thus, you can use the video components and the TV as if they were connected directly. • This function takes effect for the following sources—DVR/DVD, VCR, and VIDEO. When operating the receiver To activate (or deactivate) TV Direct, follow the proced
Résumé du contenu de la page N° 19
To cancel the Sleep Timer: Press SLEEP repeatedly so that “SLEEP OFF” appears on the Turning off the sounds temporarily display. (The SLEEP indicator goes off.) • The Sleep Timer is also canceled when: From the remote control ONLY: – You turn off the receiver, or Press MUTING to turn off the sound through all – TV Direct is activated. connected speakers and headphones connected. “MUTING” appears on the display and the volume turns off. Basic adjustment of auto memory EQ C.TONE VIRTUAL SB AUDIO P
Résumé du contenu de la page N° 20
2 Press and hold SMART SURROUND SETUP until “SETTING UP” flashes on the display. Basic settings EQ C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE LPCM L C R PL ATT NEO : 6 HP DOLBY D S . WFR LFE DTS AAC DSP 3D MHz LS SB RS 96 / 24 AUTO SR kHz 3 Confirm that “SETTING UP” stops flashing, then clap your hands over your head once while “SETTING UP” still remains on the display. To obtain the best possible sound effect from Surround/DSP The receiver starts detec
