Instruction d'utilisation John Deere OMPFP10808

Résumé du contenu de la page N° 1

iGuide
OPERA T OR’S MANUAL
iGuide
OMPFP10808 ISSUE J0 (ENGLISH)
CALIFORNIA
Proposition 65 W arning
Diesel engine exhaust and some of its constituents
are known to the State of California to cause cancer ,
birth defects, and other reproductive harm.
If this product contains a gasoline engine:
W ARNING
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer , birth defects or other reproductive harm.
The State of California requires the above two wa

Résumé du contenu de la page N° 2

Introduction www .StellarSupport.com NOTE: Product functionality may not be fully represented in this document due to product changes occurring after the time of printing. Read the latest Operator ’ s Manual and Quick Reference Guide prior to operation. T o obtain a copy , see your dealer or visit www .StellarSupport.com OUO6050,0000FB1 ­19­10AUG10­1/1 Foreword WELCOME to the GreenStar™ system of fered by John tracing the components should they be stolen. Y our dealer Deere. also needs these num

Résumé du contenu de la page N° 3

Contents Page Page Unified Inch Bolt and Screw T orque V alues ........ 40­2 Safety .......................................................... 05­1 Getting Started Theory of Operation ............................................ 10­1 Making Implement Guidance Function ............... 10­2 Accuracy ............................................................. 10­2 iGuide Activation ................................................. 10­3 Useful Buttons and Icons ....................................

Résumé du contenu de la page N° 4

Contents 1021 10 ii PN=2

Résumé du contenu de la page N° 5

Safety Recognize Safety Information This is a safety­alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury . Follow recommended precautions and safe operating practices. DX,ALER T ­19­29SEP98­1/1 Understand Signal W ords A signal word—DANGER, W ARNING, or CAUTION—is used with the safety­alert symbol. DANGER identifies the most serious hazards. DANGER or W ARNING safety signs are located near specific hazards. General precautions a

Résumé du contenu de la page N° 6

Safety Park Machine Safely Before working on the machine: Lower all equipment to the ground. • Stop the engine and remove the key . • Disconnect the battery ground strap. • Hang a "DO NOT OPERA TE" tag in operator station. • DX,P ARK ­19­04JUN90­1/1 Prepare for Emergencies Be prepared if a fire starts. Keep a first aid kit and fire extinguisher handy . Keep emergency numbers for doctors, ambulance service, hospital, and fire department near your telephone. DX,FIRE2 ­19­03MAR93­1/1 1021 10 05­2 P

Résumé du contenu de la page N° 7

Safety Practice Safe Maintenance Understand service procedure before doing work. Keep area clean and dry . Never lubricate, service, or adjust machine while it is moving. Keep hands, feet , and clothing from power­driven parts. Disengage all power and operate controls to relieve pressure. Lower equipment to the ground. Stop the engine. Remove the key . Allow machine to cool. Securely support any machine elements that must be raised for service work. Keep all parts in good condition and properly

Résumé du contenu de la page N° 8

Safety Keep Riders Off Machine Only allow the operator on the machine. Keep riders of f. Riders on machine are subject to injury such as being struck by foreign objects and being thrown of f of the machine. Riders also obstruct the operator ’ s view resulting in the machine being operated in an unsafe manner . DX,RIDER ­19­03MAR93­1/1 Handle Electronic Components and Brackets Safely Falling while installing or removing electronic components mounted on equipment can cause serious injury . Use a l

Résumé du contenu de la page N° 9

Getting Started Theory of Operation Implement Harness(s) for receiver (quantity may vary) • Implement GPS Bracket and receiver • iGuide is a passive implement guidance system which Compatible only with GreenStar™ 2 2600 display (GS2) • allows a machine to be driven in such a way as to keep and GreenStar™ 3 2630 (GS3) the implement on its desired track. It is able to do this with a StarFire™ GPS receiver on both the machine and Software and Settings: the implement. Update StarFire receiver softwa

Résumé du contenu de la page N° 10

Getting Started Making Implement Guidance Function NOTE: Make sure AutoT rac is properly setup and Implement Guidance will work with pull type implements adjustments are completed prior to using iGuide. only . NOTE: iGuide performance is contingent upon the ability The following criteria are required: of the machine to compensate for the implement. If In iGuide mode, both receivers must have the same • the machine is not weighted properly or slippage is receiver level (R TK) excessive, iGuide pe

Résumé du contenu de la page N° 11

Getting Started iGuide Activation iGuide Order Number • GreenStar display Serial Number • See GreenStar Display Operator Manual for activating. GreenStar display Challenge Code • T o activate iGuide, please visit www .StellarSupport.com or call our Customer Contact Center with the following items in hand: CZ76372,00001CB ­19­12OCT10­1/1 PC8663 —UN—05AUG05 Useful Buttons and Icons The MENU Softkey allows access to all display applications. The MENU Softkey will be on every display screen. MENU So

Résumé du contenu de la page N° 12

Getting Started PC9966 —UN—09FEB07 Use the ST ARFIRE IMPLEMENT Softkey to setup the implement Receiver and start the TCM calibration for this receiver . The Serial Number of the receiver is shown on this button. NOTE: The implement receiver must be a StarFire iTC. ST ARFIRE IMPLEMENT Softkey CZ76372,00001CC ­19­12OCT10­5/1 1 PC12947 —UN—12OCT10 Press the GUIDANCE Softkey to input required information on desired Guidance Operation. Guidance Softkey CZ76372,00001CC ­19­12OCT10­6/1 1 PC12948 —UN—12

Résumé du contenu de la page N° 13

Getting Started PC10846 —UN—07DEC07 Use Of fset T oggle button to toggle lateral of fset from left to right and vice versa. Offset T oggle Button CZ76372,00001CC ­19­12OCT10­10/1 1 Machine icon on guidance screen represents the location of the machine. Implement icon on guidance screen represents the location of the implement. Guidance reference point on guidance screen represents the location of the guidance point for the system. A— Guidance Screen C— Implement Icon Guidance Screen Icons B— Mac

Résumé du contenu de la page N° 14

Setup Getting Started Guidance Setting—T racking mode, Implement • Guidance Mode, and iGuide settings T o make iGuide function, the following criteria are required to be setup: These items can be set up separately or the Setup Wizard Machine setup and of fsets can be used by checking the Implement Guidance option • Implement setup and of fsets (M). T o access the Setup Wizard, select Softkey (F) • Machine GPS receiver settings under StarFire softkey (GreenStar). • Implement GPS receiver settings

Résumé du contenu de la page N° 15

Setup PC8663 —UN—05AUG05 Machine Setup MENU >> GREENST AR >> EQUIPMENT allows access to MACHINE and IMPLEMENT setup screens. MENU Softkey PC12685 —UN—14JUL10 GREENST AR 3 Softkey PC12948 —UN—12OCT10 EQUIPMENT Softkey Continued on next page CZ76372,00001CE ­19­12OCT10­1/2 1021 10 15­2 PN=15

Résumé du contenu de la page N° 16

Setup Machine T ab A— Machine T ab D— Machine Model Drop­Down G—Machine T urn Radius J— Recording Source Drop­Down B— Implement 1 T ab Menu Input­Box Menu C— Machine T ype Drop­Down E— Machine Name Drop­Down H— T urning Sensitivity Input­Box K— Record/Pause Button Menu Menu I— Change Offsets Button L— Enable Monitoring W ithout F— Connection Point Drop­Down GPS Check Box Menu NOTE: Machine name must be defined in order to ­ Rear Pivot Drawbar change offsets. All offsets will be saved under ­ Rea

Résumé du contenu de la page N° 17

Setup PC8663 —UN—05AUG05 Machine Offsets Change Offsets MENU >> GREENST AR2 PRO Softkey >> EQUIPMENT MENU Softkey Softkey PC12685 —UN—14JUL10 Press CHANGE OFFSET button on Machine Setup screen. Enter machine of fsets: GREENST AR 3 Softkey PC12948 —UN—12OCT10 EQUIPMENT Softkey PC1 1204 —UN—14JUL08 CHANGE OFFSETS Button Continued on next page CZ76372,00001DC ­19­12OCT10­1/3 1021 10 15­4 PN=17

Résumé du contenu de la page N° 18

Setup In­Line distance from non­steering axle to GPS receiver (B) will be Row crop tractors—rear axle • Articulated tractors—front axle • T rack tractors—rear axle • NOTE: Offset (B) for track tractors should be measured from the receiver to the pivot point. Of fset T oggle button (E) toggles the receiver from the left side of machine to the right side. V erify that the correct connection point is selected and measure from the center of non­steering axle to the center of connection point (Exampl

Résumé du contenu de la page N° 19

Setup PC8663 —UN—05AUG05 Implement Setup NOTE: The implement setup should be verified before operating iGuide. MENU button MENU >> GREENST AR >> EQUIPMENT >> Then press PC12685 —UN—14JUL10 Implement T ab GREENST AR 3 Softkey PC12948 —UN—12OCT10 EQUIPMENT Softkey Continued on next page CZ76372,00001CF ­19­12OCT10­1/2 1021 10 15­6 PN=19

Résumé du contenu de la page N° 20

Setup Implement T ab A— Machine T ab D— Implement T ype Drop­Down G—Change Offsets Button B— Implement 1 T ab Menu H— GPS Offsets Button C— Implement 2 T ab E— Implement Model Drop­Down I— Change W idths Buttons Menu F— Implement Name Drop­Down Menu Press Implement 1 tab to get to the implement setup page. For the implement setup, the following information is required to be populated: NOTE: All offsets including GPS offsets on the implement will be stored to the implement name. Implement T ype (