Résumé du contenu de la page N° 1
Basic Useful
Introduction Quick Start Setup Connections Appendix
Operation Features
MULTIMEDIA PROJECTOR
MODEL
XG-MB55X
XR-20X/XR-20S
XR-10X/XR-10S
OPERATION MANUAL
Résumé du contenu de la page N° 2
IMPORTANT • For your assistance in reporting the loss Model No.: or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this Serial No.: information. • Before recycling the packaging, please ensure that you have checked the con- tents of the carton thoroughly against the list of “Supplied accessories” on page 10. SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorpo
Résumé du contenu de la page N° 3
iii
Résumé du contenu de la page N° 4
The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian, Dutch, Portuguese, Chinese and Korean. Carefully read through the operation instructions before operating the projector. Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch, Italienisch, Niederländisch, Portugiesisch, Chinesisch und Koreanisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durc
Résumé du contenu de la page N° 5
Introduction Before using the projector, please read this operation manual carefully. Introduction ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of
Résumé du contenu de la page N° 6
INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. However, there is no guarantee that
Résumé du contenu de la page N° 7
Introduction Useful Features How to Read this Operation Manual The specifications are slightly different, depending on the model. However, you can connect and operate all models in the same manner. • In this operation manual, the illustration and the screen display are simplified for explanation, and may differ slightly from the actual display. Using the Menu Screen ENTER button Adjustment buttons (P/R/O/Q) MENU/HELP button Adjustment buttons (P/R/O/Q) MENU/HELP button ENTER button Buttons use
Résumé du contenu de la page N° 8
Contents Preparing Introduction Setup How to Read this Operation Manual .... 3 Setting up the Projector ...................... 18 Contents ............................................... 4 Setting up the Projector ....................... 18 Standard Setup (Front Projection) ....... 18 IMPORTANT SAFEGUARDS ............... 6 Ceiling-mount Setup ............................ 18 How to Access the PDF Operation Projection (PRJ) Mode ......................... 19 Manuals ................................
Résumé du contenu de la page N° 9
Introduction Reference Appendix Connecting Pin Assignments ............. 53 RS-232C Specifications and Command Maintenance ....................................... 47 Settings ............................................ 54 Maintenance Indicators ...................... 48 Computer Compatibility Chart ............ 58 Regarding the Lamp ........................... 50 Troubleshooting .................................. 59 Lamp ..................................................... 50 For SHARP Assista
Résumé du contenu de la page N° 10
IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing. 1. R
Résumé du contenu de la page N° 11
Introduction 15. Overloading 19. Replacement Parts Do not overload wall outlets, extension cords, or When replacement parts are required, be sure integral convenience receptacles as this can the service technician has used replacement result in a risk of fire or electric shock. parts specified by the manufacturer or have the same characteristics as the original part. 16. Object and Liquid Entry Unauthorized substitutions may result in fire, Never push objects of any kind into this product electr
Résumé du contenu de la page N° 12
Observe the following safeguards when setting up your projector. When using the projector in high-altitude Caution concerning the lamp unit Potential hazard of glass par- areas such as mountains (at altitudes of ticles if lamp ruptures. In approximately 1,500 meters (4,900 feet) case of lamp rupture, contact or more) your nearest Sharp Autho- When you use the projector in high-altitude rized Projector Dealer or Ser- areas with thin air, set “Fan Mode” to “High”. vice Center for replacement.
Résumé du contenu de la page N° 13
Introduction When turning off the projector, the cooling fan Using the projector in other countries runs to decrease the internal temperature for The power supply voltage and the shape of a while. Unplug the power cord after the cool- the plug may vary depending on the region ing fan stops. The period the cooling fan runs or country you are using the projector in. will vary, depending on the circumstances and When using the projector overseas, be sure the internal temperature. to use an appr
Résumé du contenu de la page N° 14
Accessories Supplied accessories Two R-6 batteries RGB cable Lens cap (attached) Remote control (“AA” size, UM/SUM-3, (10' (3.0 m)) CCAPHA024WJSA RRMCGA398WJSA HP-7 or similar) QCNWGA045WJPZ DIN-D-sub RS-232C adaptor 57 (5 /64" (15 cm)) (Only supplied with XG-MB55X) QCNWGA015WJPZ Power cord* (1) (2) (3) (4) For U.S. and For Europe, For U.K. and For Australia, New Canada, etc. except U.K. Singapore Zealand and Oceania (6' (1.8 m)) (6' (1.8 m)) (6' (1.8 m)) (6' (1.8 m)) QACCDA007WJPZ QACCVA011WJP
Résumé du contenu de la page N° 15
Introduction Part Names and Functions Numbers in Z refer to the main pages in this operation manual where the topic is explained. Projector Top View Power Lamp indicator 27, 48 27, 48 indicator Temperature warning 48 indicator STANDBY/ON 27 button For turning the power on and Volume buttons 30 putting the (–O/Q+) projector into For adjusting the speaker standby mode. sound level. INPUT button (P/R) 30 ENTER button For switching input mode 37 For setting 1, 2, 3 or 4. items selected or adjusted o
Résumé du contenu de la page N° 16
Part Names and Functions (Continued) Numbers in Z refer to the main pages in this operation manual where the topic is explained. Rear View Terminals Refer to “INPUT Terminals and Connectable Main Equipment” on page 21. OUTPUT (INPUT 1, 2) AUDIO (INPUT 1, 2) 23 25 terminal terminal (Shared for 24 (Shared computer RGB and INPUT 1 and 2) component signals output terminal for INPUT 1 and 2) Terminal for connecting a monitor. INPUT 1 and 23 INPUT 2 terminals 24 INPUT 3 terminal Terminals for 24 Termi
Résumé du contenu de la page N° 17
Introduction Numbers in Z refer to the main pages in this operation manual where the topic is explained. STANDBY button ON button 27 27 For putting the For turning the power on. projector into the standby mode. MENU/HELP button 37 For displaying adjustment KEYSTONE button 31 46 and setting screens, and For entering the help screen. Keystone Correction mode. RETURN button 37 Adjustment buttons 37 For returning to the (P/R/O/Q) previous menu screen • For selecting menu items. during menu operation
Résumé du contenu de la page N° 18
Part Names and Functions (Continued) Inserting the Batteries Press the P mark on the cover and slide it in the 1 direction of the arrow. Insert the batteries. 2 • Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment. Attach the cover and slide it until it clicks into place. 3 Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below. Caution • Danger of explosion if battery is incorrectly repl
Résumé du contenu de la page N° 19
Introduction Usable Range Remote control sensor The remote control can be used to control the projector within the ranges shown in the illustra- tion. Note • The signal from the remote control can be re- flected off a screen for easy operation. How- ever, the effective distance of the signal may differ depending on the screen material. 30° When using the remote control • Ensure that you do not drop, expose to mois- Remote ture or high temperature. control signal • The remote control may malfunct
Résumé du contenu de la page N° 20
Quick Start This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example. 3 STANDBY/ON STANDBY button 8 8 button INPUT button 6 ON button 3 ENTER button 4 KEYSTONE button 7 KEYSTONE 7 button ENTER button 4 INPUT 1 button Focus ring 6 4 HEIGHT 4 ADJUST lever _P. 18 1. Place the projector facing a wall or a sc
