Résumé du contenu de la page N° 1
USA & Canada
(800) 421-1587 & (800) 392-0123
(760) 438-7000
Toll Free FAX (800) 468-1340
www.linearcorp.com
INSTALLATION AND
OWNER’S MANUAL
AUJ-S & AUH-S
AU SERIES WITH SOLID STATE CONTROL CIRCUITRY
JACKSHAFT COMMERCIAL
VEHICULAR DOOR OPERATORS
107172
Serial #:
READ THIS MANUAL
Date Installed:
CAREFULLY BEFORE
Your Dealer:
As of date of manufacture,
INSTALLATION OR USE
meets all ANSI/UL 325
Safety Requirements for
Vehicular door operators.
SAVE THESE INSTRUCTIONS !
Résumé du contenu de la page N° 2
TABLE OF CONTENTS 2 Product Features........................................................................................................... 3 Jackshaft Operator Applications ................................................................................. 3 Preparation .................................................................................................................... 4 Figure 1 - Component Identification Pictorial .......................................................
Résumé du contenu de la page N° 3
PRODUCT FEATURES 3 Momentary Contact To Close: Standard operating mode. Requires a photo-beam as described above or one of the Miller The purpose of this booklet is to provide assembly, installation Edge family of Door Edge devices as described on this page to and operation information concerning Model AUJ-S & AUH-S be properly installed on the door and connected to the Commercial Vehicular Garage Door Operators and related operator. See Page 12 for the entrapment protection Accesso
Résumé du contenu de la page N° 4
PREPARATION 4 verify that it is the correct model for the intended application WARNING and that the voltage and phase are in accordance with electrical power provided at the job site. If the operator was ELECTRIC DOOR OPENERS ARE DESIGNED ordered with the optional chain hoist, ..H.. suffix, see that it is FOR DOORS IN GOOD WORKING CONDITION, so equipped. A chain hoist CANNOT be added in the field. PROPERLY COUNTERBALANCED AND Warning: Rope off the area to keep personnel and PROP
Résumé du contenu de la page N° 5
IMPORTANT INSTALLATION INSTRUCTIONS! 5 TO REDUCE THE RISK OF SEVERE WARNING INJURY OR DEATH: READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS! • Install only on a properly operating and balanced • Install the door operator at least 8 feet or more garage door. A door that is operating improperly above the floor if the operator has exposed moving could cause severe injury. Have qualified service parts. personnel make repairs to cables, spring assemblies • Do not connect the opener to
Résumé du contenu de la page N° 6
INSTALLATION INSTRUCTIONS 6 SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE USED TO BALANCE YOUR GARAGE DOOR ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SEVERE INJURY OR DEATH IF DISTURBED. WARNING DO NOT ATTEMPT ADJUSTMENT. construction of the surface supporting the operator or noticeable Figure 4, page 8 illustrates several positions suitable for deflection of the door shaft, it is advisable to install a shaft mounting the operator; right hand or left hand, either wall mo
Résumé du contenu de la page N° 7
INSTALLATION INSTRUCTIONS 7 DIRECT COUPLING MOUNTING CHAIN HOIST AND FLOOR DISCONNECT INSTALLATION Figure 4, page 8 illustrates several positions suitable for mounting the operator including center mount with direct If the operator is furnished with a chain hoist (Model AUH-S), pass coupling to the torsion shaft. Direct coupling may also be the hand chain over the chain wheel and through the chain guides used in a side mount installation. Operators intended for on the operator clutc
Résumé du contenu de la page N° 8
FIGURE 4 - OPERATOR MOUNTING POSITIONS 8 Center Right Side Left Side Mount Mount Mount Direct Ceiling Couple Mount Ceiling Mount Wall Mount Wall Mount 100719 Figure 4
Résumé du contenu de la page N° 9
FIGURE 5 - OPERATOR DIMENSIONS - MODEL AUH-S 9 7.75 107173 Figure 5 NOTE: Dimensions for Model AUJ-S are similar to above, Model AUJ-S is not provided with a chain hoist.
Résumé du contenu de la page N° 10
FIGURE 6 - OPERATOR DIMENSIONS - MODEL AUJ-S 10 15 7.75 107173 NOTE: Dimensions for Model AUH-S are similar to above, Model AUH-S is provided with a chain hoist. Figure 6
Résumé du contenu de la page N° 11
INSTALLATION INSTRUCTIONS 11 4) Depress the limit nut retaining Plate (D) so it disengages WARNING from the slots in the limit nuts. Turn the OPEN limit nut (E) on the shaft until it engages the Open Limit Switch (A). You will need to listen for an audible click. Release the retaining plate TO AVOID RISK OF ENTRAPMENT AND and be sure that it engages in slots of both limit nuts. POSSIBLE DAMAGE TO THE DOOR AND OPERATOR THE LIMITS MUST BE ADJUSTED 5) Manually lower the door to approx.
Résumé du contenu de la page N° 12
INSTALLATION INSTRUCTIONS - ELECTRICAL WIRING 12 WARNING WARNING RISK OF ENTRAPMENT THAT MAY TO PREVENT THE RISK OF PERSONAL INJURY OR DEATH : RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DISCONNECT POWER TO THE • DISCONNECT POWER AT THE FUSE BOX OPENER BEFORE AND DURING BEFORE PROCEEDING. • ELECTRICAL CONNECTIONS MUST BE MADE INSTALLATION OF AN ACCESSORY REVERSING DOOR EDGE OR BY A QUALIFIED INDIVIDUAL. PHOTOELECTRIC DEVICE. DO NOT • OBSERVE LOCAL ELECTRICAL COD
Résumé du contenu de la page N° 13
DOOR EDGE and PHOTOELECTRIC INSTALLATION 13 Note: See the door edge manufacturer‟s installation instructions for the complete installation procedure. See Figure 9 for connecting the edge to the operator. See Page 17 for proper setting of the selector switches. These switches must be properly set and an approved photo- electric device or approved door edge device connected to the operator to obtain B2 Mode of Operation, Momentary Contact to Close. Figure 8 Door Edge Device Door Edge
Résumé du contenu de la page N° 14
OPEN CLOSE STOP TB1 INSTALLATION INSTRUCTIONS 14 ENTRAPMENT PROTECTION DEVICES WIRING INSTRUCTIONS Note A: Connect only one (1) approved entrap- ment protection device to terminals “Photo” and Any Miller Edge ME, MT/MU, and CPT “Com”. If additional entrapment protection is desired family of edges, must be connected to the connect additional photoelectric and door edges devices SM-102 Edge Module, Recognized by UL as per UL325 2010 on 08-29-2010. to “NC REV”, “NO REV” and “COM” termi
Résumé du contenu de la page N° 15
3/SINGLE BUTTON STATION / INTERLOCK FIELD WIRING 15 R5 D3 R57 R25 R65 RADIO MOTOR C24 C10 R84 R2 24V D2 D8 R3 COM U5 MOTOR CONTROL C25 RM3 RM2 PB1 PB2 PB3 CONTROL RM1 BOARD D12 VCC P7 R38 BOARD R54 OPEN CLOSE STOP R87 R55 R94 R56 R95 R2 R3 C25 PB1 PB2 PB3 D12 OPEN CLOSE STOP Figure 10 Single 3 Button Station Multiple 3 Button Station Figure 11 R93 D1 U5 R4 R8 C21 R24 Figure 12 MOTOR CONTROL TB1 BOARD Single Button and External Interlock Wiring Note: When adding an External Int
Résumé du contenu de la page N° 16
OPERATION & ADJUSTMENT INSTRUCTIONS 16 IMPORTANT SAFETY INSTRUCTIONS FOR OWNER TO REDUCE THE RISK OF SEVERE WARNING INJURY OR DEATH: READ AND FOLLOW ALL INSTRUCTIONS! Understand all of the operating features of your door control system at the time of its installation. Your installing dealer will demonstrate them for you. NEVER let children operate or play with door controls. Keep the Remote Control (where provided) away from children. Personnel should keep away from a door in moti
Résumé du contenu de la page N° 17
OPERATION & ADJUSTMENT INSTRUCTIONS 17 SETTING THE SWITCH SELECTABLE OPERATING MODES Changing the Switch Selectable Operation Modes Settable P4 The following modes are selected by setting the on-board dip Switches switches, Figure 20 at right shows where the switches are Location K5 K3 K4 K2 located on the operator control board. For each Operational HIGH VOLTAGE K6 Mode, the switches are set to either ON or OFF according to the P1 TR3 POWER STATUS MO4 SW1 MO3 table at right below. F
Résumé du contenu de la page N° 18
OPERATION & ADJUSTMENT INSTRUCTIONS 18 Mid-Stop: Activation stops an opening door; momentary contact will reactivate the auto close timer or reset the auto close timer of open button at mid stop will restart door to full open position; when the door is at the mid-stop or open limit. if door is moving open, constant pressure on open button will T Operation, Dip-Switch Setting bypass mid-stop. Open Button: Momentary activation; open override of closing Auto Close Timer: N/A door. Close But
Résumé du contenu de la page N° 19
OPERATION & ADJUSTMENT INSTRUCTIONS 19 After moving the door to the close position and temporarily Mid-Stop Limit Setup setting the switches to the appropriate settings in the table, This features provides a timing function to stop a door as it is pressing STOP will clear and turn off the auto close timer. traveling open at a Mid Stop position instead of the full open Every time OPEN is pressed, 5 seconds is added to the time. position. The door can then be moved to the full open posi
Résumé du contenu de la page N° 20
OPERATION & ADJUSTMENT INSTRUCTIONS 20 CLUTCH ADJUSTMENT RUBBING AGAINST THE DOOR STOPS OR DEFECTIVE OR MISADJUSTED SPRINGS. ANY WARNING SERVICE REQUIRED TO THE DOOR, DOOR SPRINGS OR DOOR OPERATOR MUST BE PREFORMED BY A RISK OF ENTRAPMENT THAT MAY RESULT QUALIFIED PROFESSIONAL DOOR INSTALLER. IN SERIOUS PERSONAL INJURY OR DEATH. DISCONNECT POWER TO THE OPENER The clutch pad will wear during normal operation and should be replaced when it becomes difficult or impossible to suffi
