Résumé du contenu de la page N° 1
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
®
GARAGE DOOR OPENER
For Residential Use Only
Model 1220E FS2
Model 1210E FS2
Owner’s Manual
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
■ Periodic checks of the opener are required to ensure safe operation.
■ The model number label is located on the front panel of your opener.
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Introduction Pages 2-8 Adjustment Pages 29-31 Safety symbol and signal word review........................2 Adjust the travel limits ...............................................29 Preparing your garage door ........................................3 Adjust the force .........................................................30 Tools needed...............................................................3 Test the safety reversal system.................................31 Planning
Résumé du contenu de la page N° 3
1 Preparing your garage door WARNING WARNING Before you begin: To prevent possible SERIOUS INJURY OR DEATH: • Disable locks. • ALWAYS call a trained door systems technician if CAUTION WARNING • Remove any ropes connected to garage door. garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when • Complete the following test to make sure your required. garage door is balanced and is not sticking or binding: • NEVER try to loosen, move or adjust garage door, d
Résumé du contenu de la page N° 4
• Look at the garage door where it meets the floor. Planning Any gap between the floor and the bottom of the Identify the type and height of your garage door. door must not exceed 6 mm. Otherwise, the safety Survey your garage area to see if any of the reversal system may not work properly. See conditions below apply to your installation. Additional Adjustment Step 3. Floor or door should be materials may be required. You may find it helpful to repaired. refer back to this
Résumé du contenu de la page N° 5
Slack in Chain Tension is Normal When Garage Door is Closed Planning (Continued) WARNING WARNING ONE-PIECE DOOR INSTALLATIONS Without a properly working safety reversal system, persons (particularly small children) could be • Generally, a one-piece door does not require CAUTION SERIOUSLY INJURED or KILLED by a closing garage WARNING reinforcement. If your door is lightweight, refer to door. the information relating to sectional doors in • The gap between the bottom of the garage door and Install
Résumé du contenu de la page N° 6
Planning (Continued) WARNING WARNING GATE INSTALLATIONS Without a properly working safety reversal system, persons (particularly small children) could be • It is recommended that you attach fine mesh or CAUTION SERIOUSLY INJURED or KILLED by a closing gate. WARNING screening across the inside of swinging or sliding • Activate gate ONLY when the gate is in full view and gates in order to prevent intruders from reaching free from any obstructions. through the bars and releasing the trolley from t
Résumé du contenu de la page N° 7
Carton Inventory Your garage door opener is packaged in one carton Parts may be stuck in the foam. Hardware for which contains the motor unit and the parts illustrated assembly and installation is shown on the next page. below. Note that accessories will depend on the Save the carton and packing material until installation model purchased. If anything is missing, carefully and adjustment is complete. check the packing material. Model 1220E Only Model 1210E Only Model 1210E 971-315LM ® 41A5577-1
Résumé du contenu de la page N° 8
NOTICE Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. Assembly Hardware 41A3534 Hex Bolt Washered Bolt Nut Carriage Bolt 5/16"-18x7/8" (3) Master Link (2) 5/16"-18x1/2" (2) 5/16"-18 (5) 1/4"-20x1/2" (12) (mounted in opener) Trolley Lock Nut Lock Washer Threaded Shaft (1) 1/4"-20x7/16" (12) 5/16" (4) Installation Hardware 41A3535 Hex Bolt Lag Screw Lock Washer Nut 5/16"-18x7/8" (4) 5/16"-9x1-5/8" (4) 5/16" (6) 5/16"-18 (6) Ring Fast
Résumé du contenu de la page N° 9
ASSEMBLY STEP 1 For Sectional and One-Piece Doors ONLY Assemble the T-Rail and HARDWARE Attach the Chain Pulley Bracket SHOWN ACTUAL SIZE To avoid installation difficulties, do not run the Carriage Bolts garage door opener until instructed to do so. Lock Nut 1/4"-20x1/2" 1/4"-20 1. Place the 3 T-rail sections on a flat surface for assembly. The end sections are identical. The center section must be positioned with the Nut Lock Washer Hex Bolt braces against the end sections as 5/16" 5/16"-18x7/
Résumé du contenu de la page N° 10
ASSEMBLY STEP 1 HARDWARE For Sliding and SHOWN ACTUAL SIZE Swinging Gates ONLY Carriage Bolts Lock Nut 1/4"-20x1/2" Assemble the T-Rail and 1/4"-20 Attach the Chain Pulley Bracket To avoid installation difficulties, do Nut Lock Washer Hex Bolt not run the garage door opener until 5/16" 5/16"-18x7/8" 5/16"-18 instructed to do so. 1. Place the 3 T-rail sections on a flat surface for assembly. The end sections are identical. Make sure the "arrow label" on the center section is pointing in the dir
Résumé du contenu de la page N° 11
HARDWARE SHOWN ACTUAL SIZE ASSEMBLY STEP 2 For Sectional and One-Piece Doors Only Install the Trolley Lock Washer Nut 5/16" 5/16"-18 • Attach the trolley threaded shaft to the trolley with the lock washer and nuts as shown. Inner Nut • As a temporary stop, insert a screwdriver into the 5/16" Lock Washer hole in the front end of the T-rail. 5/16" Trolley Outer Nut • Slide the trolley assembly along the rail to the Threaded 5/16" Shaft screwdriver stop. Trolley NOTE: If trolley hits against any
Résumé du contenu de la page N° 12
WARNING WARNING ASSEMBLY STEP 3 CAUTION WARNING Fasten the T-Rail to the Motor Unit To avoid serious damage to opener, ONLY use bolts/fasteners mounted in top of motor unit. • Place the opener on packing material to protect the cover. For convenience, put a support under the chain pulley bracket. • Remove the two 5/16"-18x1/2" washered bolts #8x1" mounted in the top of the motor unit. Washers Hex Screws • Align the holes in the back section of the T-rail with Washered Bolt Chain 5/16"-18x1/2"
Résumé du contenu de la page N° 13
ASSEMBLY STEP 4 WARNING WARNING For Sectional and To avoid possible SERIOUS INJURY to fingers from One-Piece Doors Only moving garage door opener: CAUTION WARNING • ALWAYS keep hand clear of sprocket while operating Install the Chain and Attach the opener. Sprocket Cover • Securely attach sprocket cover BEFORE operating. Leave Chain & Cable Inside Carton to INSTALLING THE CHAIN Prevent Kinking 1. Dispense a few inches of Figure 1 chain from carton and Master Link fasten to trolley with a Keep
Résumé du contenu de la page N° 14
5-15 cm ASSEMBLY STEP 4 WARNING WARNING For Sliding and To avoid possible SERIOUS INJURY to fingers from Swinging Gates Only moving opener: CAUTION WARNING • ALWAYS keep hand clear of sprocket while operating Install the Chain and Attach the opener. Sprocket Cover • Securely attach sprocket cover BEFORE operating. Leave Chain & Cable INSTALLING THE CHAIN Inside Carton to Prevent Kinking 1. Dispense a few inches of chain from carton and fasten to trolley with a master link from the Keep Chain
Résumé du contenu de la page N° 15
ASSEMBLY STEP 5 Tighten the Chain Lock Washer Outer Nut • Spin the inner nut and lock washer down the Inner Nut trolley threaded shaft, away from the trolley. To Tighten Outer Nut • To tighten the chain, turn outer nut in the direction To Tighten shown. AS YOU TURN THE NUT, KEEP THE Inner Nut CHAIN FROM TWISTING. • When the chain is approximately 13 mm above the base of the T-rail at its midpoint, re-tighten the inner nut to secure the adjustment. Sprocket noise can result if chain is either too
Résumé du contenu de la page N° 16
INSTALLATION STEP 1 Finished Vertical Ceiling Determine the Header Bracket Centerline 38 mm Header Location Board Structural Wall Supports WARNING WARNING To prevent possible SERIOUS INJURY or DEATH: • Header bracket MUST be RIGIDLY fastened to CAUTION WARNING structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall. Vertical • Concrete anchors MUST be used if mounting header Centerline of Garage Door bracket
Résumé du contenu de la page N° 17
ONE-PIECE DOOR WITHOUT TRACK Unfinished Ceiling 1. Close the door and mark the inside vertical centerline of your garage door. Extend the line Structural onto the header wall above door, as shown. Vertical Supports Header Wall Centerline If headroom clearance is minimal, you can install 38 mm Board the header bracket on the ceiling. See page 18. 38 mm Board If you need to install the header bracket on a OPTIONAL 38 mm board (on wall or ceiling), use lag screws CEILING MOUNT FOR (not provided
Résumé du contenu de la page N° 18
INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall Wall Mounting Holes above the garage door, or to the ceiling. Follow the CEILING MOUNT ONLY instructions which will work best for your particular The nail hole is for positioning only. requirements. Do not install the header bracket You must use lag screws UP over drywall. If installing into masonry, use to mount the header bracket. concrete anchors (not provided). WALL HEADER BRACKET INSTALLATI
Résumé du contenu de la page N° 19
INSTALLATION STEP 3 Attach the T-Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a Header Wall protective base. NOTE: If the door spring is in the way you’ll need Header Bracket help. Have someone hold the opener securely on a temporary support to allow the rail to clear the Chain spring. Pulley Bracket • Position the rail bracket against the header bracket. • Align the bracket holes and join with a clevis pin as shown. • Ins
Résumé du contenu de la page N° 20
WARNING WARNING INSTALLATION STEP 4 CAUTION WARNING Position the Opener To prevent damage to garage door, rest garage door opener rail on 38 mm board placed on top section of Follow instructions which apply to your door type as door. illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 38 mm board is convenient for setting an ideal 38 mm door-to-T-rail distance. Header Board Rail Bracket • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough
